Polaris snowmobile Clutch Rebuild. P85 drive primary clutch Vintage Polaris Snowmobiles. ATV SXS UTV
Автокөліктер мен көлік құралдары
Polaris Snowmobile Clutch Rebuild.
Shirts and stickers are here: nutters-speed-shop.myspreadsh...
Want to support the channel? Go To Nutter's Speed Shop Patreon Page: / nuttersspeedshop
or
Send beer and pizza funds through Pay Pal to nuttersspeedshop@gmail.com. No questions about sleds will be answered by e-mail. Leave a comment. Comments help the channel, e-mails don't.
or
Want to send Farley dog treats or send something to Nutter's Speed Shop?
P.O. Box 241
Stacy Mn 55079
My favorite (almost) universal tether. Works on all vintage Polaris amzn.to/3LLn3gm
99502H 2RS bearings - oddball smaller bearings used in some Polaris skids. amzn.to/3D9yLfO
Rivnut tool we use in the shop: amzn.to/3H98pNp
The O-rings for Polaris TX carbs amzn.to/3wc25hG
Shoe Goo -- Fix your sled seat! amzn.to/3XAJfgc
Shake and Break! The Ultimate Philips impact driver! amzn.to/3CcJgyk
62052RS bearing I have been using. Cheap, but seem OK for my use: amzn.to/3h2ZimS
Wix 33001 1/4" Fuel Filter for sleds: amzn.to/3zs1x9A
Brass 3/4" hose barbs: amzn.to/3Fvrjh4
Spring Compressor - right size for sleds: amzn.to/3MU5Jo1
Really deep 12mm socket for above compressor: amzn.to/3uIDyjE
9/16 6 point socket, 1/4" drive: amzn.to/3EYDQcF
Mayhew Dominator Pry Bar set: QUALITY!!! amzn.to/3yvg0B6
Genuine Hella H4 headlight for wedge Indys: amzn.to/3LjQOmq
Insulation for belly pan near pipes: amzn.to/3DqyOEU
7PSI lever lock radiator cap for Vintage Polaris (large cap) amzn.to/3BhUjVN
1/4-20 flat nuts for vintage Polaris: amzn.to/3qGa18e
9mm hose clamp for fuel lines: amzn.to/3xBS51Q
Three Bond 12-11: amzn.to/3JVU4CM
Ultrasonic cleaning solution that I use: amzn.to/3scP7PX
Heavy Duty Voltage Regulator: amzn.to/3sY1m1W
LED light that fits TX and TXL: amzn.to/3Hcb2vE
Пікірлер: 28
Want to support the channel? Go To Nutter's Speed Shop Patreon Page: www.patreon.com/nuttersspeedshop
I bet that unit will come in handy at some point, thanks for sharing!!
@nuttersspeedshop
10 ай бұрын
You bet
Thanks for posting. After watching I’ve decided to hose it with dry graphite spray and hope for the best. Just needs to be good enough to pull a toboggan. Cheers!
Looks like me last week doing the same job, crocks and shorts! Have a good one
@nuttersspeedshop
10 ай бұрын
Rock on!
I’ve only rebuilt one primary clutch ever at my dads shop last winter for a guy’s race sled. We never used a lathe we just had screw drives and sockets to pound out and in new bushings and we used scotch bright to clean up all the surfaces. Clutch turned out great! I have a “clean” junker sled I bought last winter and the clutch has 6k miles on it and it makes noises I’ve been back and forth on rebuilding it but I might just find a used one or a new one.
🇸🇪 Thank you for a helpful video. I hav that kind of clutch on a 1990 swedish Aktiv.
I agree 1000% that it's easier to look for a better primary than to pull one apart. I've seen fixtures that have been bolted to the floor and people are using 5' cheater bars to get the spider off.
@nuttersspeedshop
10 ай бұрын
Right on. I've broken spiders too. Sometimes they just can't be saved, no matter how big of a cheater bar you have :)
Nutter that's why I buy all the p85 and p90 clutches I can new
@nuttersspeedshop
10 ай бұрын
Me too!
Should you rebuild clutches is the question. I deal with Comet clutches, but the basic design is similar. If you buy all the new parts over the counter, when you add it up, you may not be saving much. If you have acquired NOS parts considerably cheaper than the current prices, it can make sense to rebuild. I have had clutches that were too far gone to rebuild, if the fixed sheave and shaft is worn there is no way to bring things back to new specs. I have bought clutches off ebay that turned out to be very lightly used, and with a clean up and installation of application correct arms and spring, worked very well. I know guys who are willing to work on anything on a sled, but only buy new clutches, so it definitely can be a personal preference.
@nuttersspeedshop
10 ай бұрын
Right on.
@BigBenn2775
3 ай бұрын
Usually this is said by someone that’s unable to rebuild a clutch, More money then brains lol
Nutter believe it or not I've seen those fall out , I rebuilt one and it came out with in twenty minutes
@nuttersspeedshop
10 ай бұрын
Bushing fell out?
@larrywarner9314
10 ай бұрын
Yeah
Im not gonna attempt primary rebuild 😮
@jesserousseau2481
6 ай бұрын
It's very easy
i have same clutch,and i rebuilt itwith , all new rebuild parts. and bought the new movable sheave bushing, With steel retaining ring. that fiber bushing went in with a little effort. ( prior cleaned with emery , etc. and cleaner) but when i tried to install spider on the fixed sheave , it will no way slide down on the fixed shaft, two men and a boy to try to get it to slide. is it a tapered bushing? no where do i see it only goes one way. i already wrecked the first bushing with chain saw file trying to get it to slide gracefully. what the ? any info is appreciated
@davidhmurphy1619
7 ай бұрын
also, the belt surface is very clean and shiney no rust did emery cloth that too.
@nuttersspeedshop
7 ай бұрын
You did the thing I would have suggested in polishing the stem. As you discovered you can't open up the clearance or it wrecks the bushing. Make sure there's a tiny chamfer on the lead in on the stem and push it on and work it around and spin it and try to seat the bushing. If it won't loosen up I don't know what to say except polish some more and then try to push it on and work it in. They are always tight at first, but I have always been able to get them to move free by polishing and working them in.
@davidhmurphy1619
7 ай бұрын
@@nuttersspeedshop i did forget to say i did polish the shaft with emery prior to placing the spider. and yes, the tiny chamfer is there and everything looks good. thanks Man , for your input. the first one , i filed bushing w/chain saw file, ruined it. cant even push it on.
Are those steel toe crocks???
@nuttersspeedshop
9 ай бұрын
You bet LOL!
How many miles would it take to wear a clutch that bad?
@nuttersspeedshop
3 ай бұрын
I'm just guessing because the hood had been changed so the speedo was probably not giving correct mileage on that sled. Probably 5000 miles + of pure neglect.