Great video im happy I got this machine and u have like every single thing I need to do to maintain it and fix problems as they come.

Good video! Very informative great teaching through all steps thank you for the time you took to show all the steps and information needed 👍🏼

Just found your channel and subscribed like how you explain things i bought two to hopefully make one will be checking out all your vids.

@MrFixit1

9 ай бұрын

Welcome to the channel!

Just picked up a 94 off a friend who was afraid to run straight gas in it, fouls out the plugs every half tank, now I know how to check everything, thanks bud!

@eagle777dh

3 ай бұрын

I prefer oil injection. Back in the 70's I spent a lot of time in a Kawasaki shop. In hundreds of bikes that went thru it only one had a true oil pump failure. The other dozen or so that came in with problems with oil pump problems were owners messing with them and not knowing what they were doing. Simple and easy to adjust and pretty much bulletproof. The oil injection on other things like outboards are vacuum operated and not even close to the gear driven ones like this one. Had to call a guy out at the shop one time cause he said the oil pump failed when he let the tank go empty.

You are truly a professional. I admire your training skills and delivery. I tinker and understand the oil injector system way better now. Thanks I have a 1998 Polaris explorer 300 two-stroke. Thought about selling her, but I’m going to work through it

@MrFixit1

6 ай бұрын

Thank you! Have fun stay dirty!

@WagsAutomotive

4 ай бұрын

I'm getting my Polaris Sportsman 400 together. I noticed that there are vent tubes on both the engine and the transmission. I assume the transmission one vents to atmosphere and the engine one connects to the carburetor? Is that correct? And how do I adjust the idle on the engine? Is that the adjustment on the top of the carburetor? Thanks! 😊

@MrFixit1

4 ай бұрын

@tomotive !!ALL vent tubes vent to atmosphere!! Two on the carb (one overflow one bowl vent). one on engine (balance shaft compartment) one on transmission, one on gas tank, one on oil tank. ALL Vent to atmosphere! Small thumb screw on right side of carburetor adjusts Idle speed.

@WagsAutomotive

4 ай бұрын

@@MrFixit1 ok thanks! 👍

Great video. Nice job

Imma share this on the Polaris page

I have the same exact quad !!!

Really love your video. You are about my only source of information for this machine. The nearest Polaris dealer is 1 hr and 30 minutes away and they don't want to help me because the ATV is to old. My question is what transmission fluid should I use? Also is it bad to use automatic type f transmission fluid to fill the front AWD on demand hubs?

@MrFixit1

7 ай бұрын

I use Lucas Primary chain case lube in the transmission and Don't use ATF in the hubs. I use Polaris Demand Drive Fluid in the hubs. Polaris AGL gear case & transmission fluid is what is recommended for the trans.

I am looking for a coil pack and cdi box for this machine. Does anybody have a good link? I have no problem fining one for 96-01, thanks in advance

Great video, how about changing out the oil supply line? They can break/disintegrate with age.

@MrFixit1

11 ай бұрын

Sure anything can degrade with time.

Great video, whats the best way to check if the oil lamp is working?

@MrFixit1

9 ай бұрын

drain the oil tank

i just serviced the oil pump after premixing the gas for years. Now i have oil dipping from the under side of the pump housing. It looks like something might have put a small hole in the housing. It doesnt appear to be coming from the bleeder screw, could a seal gone bad causing oil to leak into the housing. I did get a steading flow of oil to the check valve when running the with the line unhooked from the valve. thanks

@MrFixit1

Жыл бұрын

OK there is supposed to be a hole in the housing from the factory for this reason. Possibly a seal failed but I would check the plastic line at the pump end for a leak. The bleed screw plastic seal would be the next culprit. It is also possible that the feed line is leaking into the housing. I haven't disassembled a pump yet to see what's inside so if you feel adventuress and you take it apart, maybe you could let us know what you found. Thanks.

@thatmodshop7160

4 ай бұрын

Why would you bother if premix has been working for years lol

Hi thanks for the videos. I bought the exact same quad a year or so ago. Only 450 miles on it. I've never heard the cooling fan kick on. I started to take the front plastics off and gave up. I saw that it does have a temperature light. My question is how often does your fan kick on? Thanks in advance

@shelbywilson114

Жыл бұрын

I did trace wires and they are connected

@shelbywilson114

Жыл бұрын

I have a 4 stroke sportsman 800 and the fan comes on a lot on it

@MrFixit1

Жыл бұрын

My fan only comes on when I work it hard like haul firewood up the hill, doesn't really come on much, takes quite a bit of riding on a hot day for my fan to come on.

Just bought a project 97 sportsman. Come to find out there is 3 holes in the case exposing the gear on the oil pump. Any idea how that would happen? Should o just delete the oil injection?

@MrFixit1

Жыл бұрын

Hole in the case Exposing the gear? Thats doesn't sound good. Wear exactly is the holes. The Oil pump gets lubricated from the balance shaft and if this oil is leaking it will cause major engine damage.

Question, just for a quick confirmation that the pump actually works, could you just pull the output hose while engine running, give throttle and check for oil coming out? That is just to check it’s working

@MrFixit1

5 ай бұрын

Yes, you can do that. Just don't let it run long because there will be no oil going into the engine. Unless you are running mix in the tank.

i have a Polaris 400Lhaving a ground issue any ideas what to look for and where,

@MrFixit1

Жыл бұрын

I'm going to need a bit more info before I can help.

Question for you. Oil pump does not spring back like yours. I replaced the spring behind it cleaned what I could see. With the cable on it or off it doesn’t have that fast snap back yours has. It get caught open slightly I believe and quad won’t start. If I push the rotating piece back to idle position it starts and runs fine. I have a spare pump it’s just nearly impossible for me to get in and work on it. I did the cable with my phone just to be able to see in there

@MrFixit1

Жыл бұрын

I'm sorry I don't understand your question.

@user-qm6kq8qf5f

Жыл бұрын

@@MrFixit1 in your video the part that the cable attaches to snaps back to closed when you let go of it. I put a new spring on mine as it wasn’t turning. It now turns but does not always go back to the idle space. I’ve found that it won’t start with the oil pump in anything other than the idle (basically fouling the plug). The not springing back is the question. Does that indicate that the pump needs to be replaced after replacing the spring

@MrFixit1

Жыл бұрын

@@user-qm6kq8qf5f If you have a replacement pump then I would replace it. You may want to take the bolts out of the fender where it mounts the floorboard and remove the Air tube that has the coolant overflow tank to get more access to replace the pump. Not much room there to work.

great video my machine is useing way to much oil. cant believe the smoke.would that be the check valve you talked about?

@MrFixit1

8 ай бұрын

Check the valve for proper function but may be something else like the cable not adjusted correctly. The more you advance the cable the more oil you get.

@davidferency3339

8 ай бұрын

@@MrFixit1 Copy that I had to replace the throttle sensor. I will check that gap that you recommend

So, I have a trail boss 350L doing my first ever top end job on it, it lost compression kind of wondering if the oil pump stopped working. I was thinking of removing the oil pump, but how do you get these Phillips screws off the pump enclosure with the lower half of the engine still in the machine?

@MrFixit1

10 ай бұрын

Try a Phillips bit and an extension on a ratchet. NOTE: Re-moving the oil pump will allow the balance shaft oil to flood into oil pump cavity and out of the oil pump housing.

@redddave

10 ай бұрын

I was going to just remove the drive and reinstall the pump to block up the opening. I try the ratch... those things are on tight!@@MrFixit1

@MrFixit1

10 ай бұрын

@@redddave There is a special tool called and impact screwdriver. You use a hammer and strike the end of the tool. Search on the net or local part stores.

I know this video is old but I got s question for you. I have a 1995 big boss 400l and took the plastics off to paint them since i had most of them off to replace the coil and cdi. I started it a couple times over the couple days i was putting it together and it ran fine and smoked like normal. Once i had everything together i started it up and took it down the street and went to park it. It died on me suddenly and i started it back up then it revved all the way up and died then sounded funny cranking and was cranking hard(couldnt use the pull start either. I pulled the plug and cranked and it sounded fine. I put it back together and now it wont start. Any ideas?

@MrFixit1

9 ай бұрын

Hard to say. I'm just speculating here but revving wildly is a sign of a vacuum leak. check the crank seal behind the drive clutch for a leak I have seen this seal back itself out of the engine before also the intake and cylinder base gasket could have blown out. Also check the crank case drain bolt. It could be something else but, that's where I would start. Hard cranking sounds like something bad. Hopefully no engine damage occurred. Might want to pull the carb or exhaust to inspect the piston. 2 stroke engines are always on the brink of destruction.

@pizzamangametime9773

9 ай бұрын

@@MrFixit1 I was looking at it this morning and discovered that there was no oil supply to the oil pump I believe it ran out of oil and committed self delete of function

@MrFixit1

9 ай бұрын

@@pizzamangametime9773 This is sadness

Ive deleted oil injection on both my xplorer 400L quads reason being is that the pump box no matter what I do to seal it, it fills up with water causing the cable to sieze, lots of guys drill holes in the plate to allow water to flow out but it honestly makes no difference. I simply dont put oil im the reservoir mix gas and go never had my mix cuase an issues years later, also take a jerry of mixed gas and regardless always have 2 stroke oil with you like you do riding a 2 stroke anyway .. Ive done the same thing with my 98-2004 RMK700 motors 🤷

@MrFixit1

4 ай бұрын

There is a rain hole in the bottom of the housing. I have not had this problem although that would be super annoying. I don't blame you for your decision. Happy riding!

@thatmodshop7160

4 ай бұрын

@@MrFixit1 man your channel is super awesome, great knowledgeable content and a wealth of information! That weed wacker gas tank/coolant reservoir idea is genius and I will be doing the same to both mine I actually found 2 new ones I hope work, do you mind of mind personally contacting me so I don't spend the $80 on tanks for nothing lol

@MrFixit1

4 ай бұрын

@@thatmodshop7160 This is my email: can1tb3fixed@gmail.com

Would letting that run dry and just filling the gas tank with pre mix cause any issues?

@MrFixit1

8 ай бұрын

I don't think so. A lot of people have done that without any issues.

@cbossplayz3555

6 ай бұрын

i personaly oppend up the pump housing and pulled the drive gear off the pump by tapping the pin out and just installed it just to be safe

Can you tell me what the override button is for on that machine?

@MrFixit1

5 ай бұрын

The "Override Button" is to bypass the reverse rev-limiter and allow AWD in reverse.

@WagsAutomotive

5 ай бұрын

@@MrFixit1 Ok my 4wd doesn't work so it's not gonna do anything for me.

@MrFixit1

5 ай бұрын

@@WagsAutomotive It will allow full power in reverse

Question: is there a way to bypass the electric hubs on the front wheels and make it full time 4wd?

@MrFixit1

5 ай бұрын

This is a bad idea but yes. Hook the gray wires from the hubs to the red/white port on the circuit board. A better way to do it is to connect the gray/white wire from the AWD switch to the red/ white, that way you can turn it on and off.

@WagsAutomotive

5 ай бұрын

@@MrFixit1 What I meant is can I eliminate the wires altogether? Is there a way to make the hubs be engaged without any power going to them?

@MrFixit1

5 ай бұрын

@@WagsAutomotive Not possible. You could get struts, hubs and axels from a 2005 Sportsman 500 shaft drive and maybe make it work. The Hillard clutch is electromagnetic, will not work without electricity. Although it would be very hard to drive this way with a solid rear and locked front. You will need arms of steel.

@WagsAutomotive

5 ай бұрын

@@MrFixit1 ok then I guess it's 2wd. Good thing I have a winch! 😁

@MrFixit1

5 ай бұрын

@@WagsAutomotive You can replace the magnet coils if that is the problem.

The problem I have is it's injecting too much oil! Is there a chance the cable is hanging up or the return spring has failed?

@MrFixit1

26 күн бұрын

Yes, there is a good chance of the happening.

@gregnapert9231

26 күн бұрын

@@MrFixit1 Thanks - will check it out.

So the oil of the engine need to full it in the front where sais oil?

@MrFixit1

3 ай бұрын

The 2 cycle oil goes in the front by the head light.

@alansgarage03

3 ай бұрын

@@MrFixit1 thats the oil of the engine ?

@MrFixit1

3 ай бұрын

@@alansgarage03 OK, I think there is a language barrier here. Just to clarify. The engine is a 2 cycle engine. The engine runs on a mix of oil and gasoline. The oil injection system uses Polaris Blue 2 cycle injection oil and gets injected into the air intake. The engine also has 100cc of 10w-30 motor oil in the balance shaft compartment to lubricate the balancer shaft. I hope this helps. Bien, creo que aquí hay una barrera del idioma. Solo para aclarar. El motor es un motor de 2 tiempos. El motor funciona con una mezcla de aceite y gasolina. El sistema de inyección de aceite utiliza aceite de inyección Polaris Blue de 2 ciclos y se inyecta en la entrada de aire. El motor también tiene 100 cc de aceite de motor 10w-30 en el compartimiento del eje de equilibrio para lubricar el eje de equilibrio. Espero que esto ayude.

looksw like on your bench setup u have some maybe marvel mystery oil cans laying horizontal w the side cut out staked on top of one another to use as storage bins/trays-am i right???

@MrFixit1

9 ай бұрын

I'm not sure what came in the cans, very well could have been Marvel Mystery Oil.

Wya i need my polaris serviced and a bayou 220 revived from the half working LOL

what year is this bike?

@MrFixit1

9 ай бұрын

1994

How much oil needs to be in the front reservoir?

@MrFixit1

4 күн бұрын

Holds two quarts keep it topped off.

@StarshipFab

4 күн бұрын

@@MrFixit1 thank you!!

Is it a bad idea maybe put couple table spoons of oil in the gas just in case oil pumps not working so it dont wreck nothing curious on ur thoughts I don't think Mines bad I just don't want to blow it up if its not getting the oil it needs?

@MrFixit1

Жыл бұрын

Really, a couple tablespoons of oil will not be near enough oil to add any safety.

@highlifegoodlife5400

Жыл бұрын

Well like half a cup or would it be bad because the carb would be get to much oil

@highlifegoodlife5400

Жыл бұрын

How often do u fill the oil tank in the front?

@MrFixit1

Жыл бұрын

@@highlifegoodlife5400 Might start fowling the spark plug at that point. Note: if it isn't smoking something is wrong. So that will be an indicator, also it will overheat and will struggle to idle.

@MrFixit1

Жыл бұрын

@@highlifegoodlife5400 I fill my oil tank once maybe twice a year but I don't ride a lot. something like every 4 or 5 gas tank full for 1 oil tank full.

Hi! I recently bought a Polaris Sportman 400 2-cycle four-track vehicle. The oil injection pump is disconnected. What mix ratio would be the best for the engine to work? Also, is it harmful for the oil injection pump to be disconnected? Thank you very much for your help!

@MrFixit1

Жыл бұрын

32-1 would be a safe ratio. As for the pump I would think it would be ok but I can't say for sure if it will cause damage running it dry. I'm sure many people do.

@luisacolon-sanchez1276

Жыл бұрын

@@MrFixit1 Thanks! Also, why does the vehicle lose power after a short time of using it?

@MrFixit1

Жыл бұрын

@@luisacolon-sanchez1276 I can't really help with that unless I had more information. Could be a lot of things.

@luisacolon-sanchez1276

Жыл бұрын

@@MrFixit1 the engine is not accelerating well. Do you happen to know what spark plug number does that engine require?

@MrFixit1

Жыл бұрын

@@luisacolon-sanchez1276 I believe it's a NGK BR8ES

What can I do in the even that it is pumping too much oil

@MrFixit1

Жыл бұрын

If you have the pump set up correctly and it is pumping too much oil, then the pump may be damaged.

@soren4869

Жыл бұрын

@@MrFixit1 If that’s the case would you just recommend a block off

@MrFixit1

Жыл бұрын

@@soren4869 Of course I recommend fixing the issue not deleting the pump

@soren4869

Жыл бұрын

So how can I turn the pump down?

@MrFixit1

Жыл бұрын

@@soren4869 if you set up the pump correctly and you are having problems replace the pump.

I've been robbing so many parts from my parts machines.for my buggy lately saves lots of time and money

Diesel mechanic here: I put new ones on customers cars, but an old timer showed me you can sand them down with a little 600grit wet sand paper, and reuse them many many times. I have done it on many of my own diesel motors with I'm sure much higher psi behind them, with not a drop dripped, hah.