No video
Pitbike head and piston change (YX 160)
We had some valve issues and we decided to update head to HC.
New engine snapped the valve and that lead to smashed piston and head so we decided to order new piston and cylinder with head (high compression).
Parts were ordered for YX 160 engine.
Part list:
Head - www.sport-toys....
Piston - www.sport-toys....
Disfigure - Blank
KZread - • Disfigure - Blank | Me...
NCS Spotify: spoti.fi/NCS
Download / Stream: ncs.io/blank
By NoCopyrightSounds
Jo Cohen & Sex Whales - We Are
KZread - • Jo Cohen & Sex Whales ...
NCS Spotify: spoti.fi/NCS
Free Download / Stream: ncs.io/jcswweare
SirensCeol & Reaktion ft. The Eden Project - Let You Know
KZread - • SirensCeol & Reaktion ...
NCS Spotify: spoti.fi/NCS
Stream here: ncs.io/letyouknow
Пікірлер: 24
Done this but when spinning the flywheel enough it comes to a complete stop won’t budge but turn it the other way goes for abit then won’t budge again?
That bike is not running correctly, the rpms are floating. And are you sure there isnt any metal parts that flew to to the cases when the bike blew up? Might cause some damage in the future.
@handsomefingers7759
3 жыл бұрын
there was air leak in rubber intake manifold and it made rpms float. and yes i am sure that there isnt any metal parts ir crankcase.
@kursutin2446
3 жыл бұрын
@@handsomefingers7759 Ok nice :)
Great video I didn’t think you could rebuild the pit bikes and sold mine when the compression went low now I see i made a mistake selling it saving for a mx bike tho
@handsomefingers7759
3 жыл бұрын
yeah and it is much cheaper choice than mx bike.
do you remember the 2 bolts inside the head you forgot to put it back on ? I lost them, do you know how long they are? Thanks !
Hello, i have a 160 but the carb hits the tensioner, were do you get that intake rubber boot from and how do you fit?
@handsomefingers7759
3 жыл бұрын
hi, you can get it from ebay or aliexpress. Rubber boot mounts on intake with screws, but depending on intake you can use silicon hose in necessary diameter.
@brotherkhan2885
3 жыл бұрын
@@handsomefingers7759 do u have facebook
How did u do the timing chain and know when it’s perfect just ordered new head for my yx160 and have no clue about the timing
@handsomefingers7759
3 жыл бұрын
turn magneto that T mark is aligned with notch in case, cam sprocket turn that lines align with notch in head.
@handsomefingers7759
3 жыл бұрын
and then put on chain
@yorkshireriding3260
3 жыл бұрын
@@handsomefingers7759 oh thankyou I’ll take a screenshot off that and let you know on day when it’s done aha
@somtingwongwai7194
3 жыл бұрын
@@yorkshireriding3260 This guy explains step by step how to do that in the video link below. should be Same principal as mention above kzread.info/dash/bejne/lnicqdCRqpjfe6w.html&lc=UgxYdWmnW-mJ1a9xrhx4AaABAg.9OXC1LK6nbH9O_HH8qb3sI
Can I have the old head?
Did you hone the cylinder or anything?
@handsomefingers7759
2 жыл бұрын
nop, cylinder didnt haave any damage
mofleta para súper cub kzread.info/dash/bejne/dWqW0cmEfKmzcaQ.html
Not one bolt tighten to spec lol
@handsomefingers7759
Жыл бұрын
And engine still runs.
@gala83filmstaylorg7
Жыл бұрын
@@handsomefingers7759 surprising