You have high Carbon Cr Mo V drill string pipe there cobber, then you have a 6010 hydrogen rich filler rod. Now you have the classic case of H2 delayed cracking, to a tee. This fault is nothing to do with magnetism it is everything to do with a high carbon equivalent and hydrogen. Preheat 95 Deg C and use a properly preconditioned E7018, clean the INSIDE of the pipe too. Wait two days for it to crack. If it doesn't you are good to go for loading it with beefies.

If it really cold outside it can do that. Never happened to me, but I’ve heard of it happening on the pipeline.

Metal expands in heat and subtract in cold weather drill holes in the bottom of the pipe to relieve the pressure.

It was a hard piece of pipe. That simple. Hi mag or hi chrome

Switch to lo-hy (7018). Either cold cracking or brittle material, or both. Peen your welds. Read up on lamellar cracking in the HAZ.

Were you using new rods or old ones? 7018 with moisture in it possibly? Ive welded lots of pipe but ive always used t-11 wire but 6011 with really rough pipe.

I’ve see it happen a couple of times. I’ve had luck welding it with 7018 and it not cracking but I also had one that would split the pipe after a 7018 weld. It’s a gamble with used pipe.

@godwinwelding7172

8 ай бұрын

Yes I have learned it does what it wants to. Thanks for watching

Thats why i use 6011 on ac mostly on pipe fence .... sometimes you cant tell theres magnetism and 6010 dc or 7018 will lay on it just fine uphill running hot but it will crack sometimes ... could be a bunch of things .... on gates and such i do 6011 ac then 7018 usually heating it up with the first pass will get rid of the magnetism enough to lay some 7018

Heat the pipe 1st then weld it. 7018 rod use a temp stick try 250f

I'm a machinist with heat treat experience that also welds. I would say that particular pipe is probably high carbon and other alloying elements. Your weld heated the steel enough to harden it, and then when it cooled and contracted the stress was enough to start a crack in the heat affected zone. Grind a v in the crack, heat it with a torch, weld it, then heat again with the torch. Check the hot zone with a magnet. Once it's no longer magnetic, critical temp has been achieved and it should be slow cooled to prevent it from hardening again. Personally, I'd probably wrap it with a welding blanket to keep it from cooling too quickly. If the ambient temperature is above 80F or so, and there's no wind, you can probably get by without that.

@godwinwelding7172

3 ай бұрын

That’s exactly what we did to fix it!

@godwinwelding7172 - I saw something like that year ago, not in a fence, but a piece of flat steel. Engineer told me it was something to do with the magnetic signal properties in metal . Didn't really understand all that he was talking about but, I would say you are spot on talking about the pipe being magnetized and causing the crack. I wonder if welding on the AC side would make a difference if you switched to 6011 instead of 6010?

@godwinwelding7172

10 ай бұрын

That’s interesting 🤔 I’m gonna have to give it a try. Thanks

@SegoMan

9 ай бұрын

@@godwinwelding7172 Couple of ways to deal with magnetized pipe. 1 - Smack it with your BFH to knock the magnetization out of it prior to the arc. 2 - 5 opposing wraps of the leads on either side of the weld

@user-jf2nc2xk1h

5 ай бұрын

​@@godwinwelding7172 Мы такие трубы варим электродами LB 52U,

It looks like it’s acting like cast iron does and pulling too much carbon into the heat affected zone, maybe a good preheat ??

@sashagertzina5558

7 ай бұрын

в этом металле много углерода . нужен предварительный нагрев

It's induction hardened pipe it does that. You need to get it slightly red let it cool weld and post heat it slowly.

@godwinwelding7172

7 ай бұрын

Thanks for the info. We will have to try that next time!

Magnetism has nothing to do with this. It only causes arc blow during welding. You have gotten hold of some very highly alloyed pipe and the heat of welding plus hydrogen in the rod has made the heat affected zone hard and brittle. You are gonna have to pre and post-heat and use a low hydrogen rod, properly conditioned in a rod oven. I have successfully welded a leaf spring on a farm trailer by pre and post heating and using that MG600 rod. It's deathly expensive but it can get you out of a jam.

@godwinwelding7172

7 ай бұрын

Thanks 🙏

That's drill rod isn't it? It's work hardened and magnetized. You need to get it blazing hot, let it cool a bit, and weld it while it is still pretty hot. And use 7018.

@godwinwelding7172

9 ай бұрын

Thanks I have had to do that ina different situation before

@mperry2384

9 ай бұрын

What? Bro travel speed was too fast. A few beads were seated in there with only hopes and wishes touching the parent metal. Fit up was bad or u tacked all horizontals and by the time u got to the top it spread that bad. Next time there's a loud pop when welding grab a square and poke around for a few

@mperry2384

9 ай бұрын

Cracks cleaner than mine. Lol gap was to big and arc force was focused on the vertical post. Gotta weave when gaps bigger than rod....

@mp-xt2rg

7 ай бұрын

​@@mperry2384he's right what you are suggesting is not correct.

@mperry2384

7 ай бұрын

​@@mp-xt2rgI expressed my opinions. How about you tell me what I'm wrong about and we can discuss it. I haven't the free time to give you a weld clinic that will fall on deaf ears

Magnetized plate and pipe will do that best way around that is an AC stick welder but not too many people use those anymore

@godwinwelding7172

7 ай бұрын

Thank you

@derekbryant6137

7 ай бұрын

@@godwinwelding7172 you're welcome my great-grandfather taught me that he was a stick welder when there was no flux on the rod he was born in 1907 and died in 99 worked on the WPA he was from Tennessee and he taught me I'm 42

I believe its a combination a few of the conditions mentioned in prior coments. Also how long is the fence, too much cooling/ contraction would add another condition to failure. There is a coment in here about high carbon content from comination of the pipe alloy an electrode type. High carbon to me in simple terms means brittle material. But the distance between the crack and weld points to brittleness in my opinoin. Weld on yall. My the weld hold you

I remember when I was in the academy , the cheif use to put some of the pieces that he hd just welded in the oil directly after welding , he said the reason why cause this type of metal , is combined with other elements , it shrinks by the high heat , then it expands after the piece cool down , thats why it crack need to stay in hot temperature till it cool down slowly to not crack , thats why he put the peice welded in oil cause it guard the temperature ,

Everybody in here telling you pre and post heat is correct, but you don't need blankets and all that fancy garbage. Just anneal it with a torch (assuming you run one) and weld that bastard hotter than normal. You'll be good if you get at least 3 inches annealed wherever your connection is

@wildnfree223

3 ай бұрын

You know to properly anneal you must slow cool it right ? ...... heat above upper critical (loses magnetism) and slow cool

Stress Crack. Right at the edge of the heat effected zone. It appears like the horizontal pipe was much cooler than the vertical pipe. The horizontal pipe sucked the heat away too fast, and that is why it cracked. The way I have seen this done that I think is better is weld a stub on the vertical pipe slip the horizontal pipe on it leaving about 2 inches of slip. When the heat is up or down it allows the horizontal growth to not effect the vertical posts.

@godwinwelding7172

3 ай бұрын

🤔🤔🤔 this is interesting. Thanks for sharing

@Hjfvvdst

3 ай бұрын

@@godwinwelding7172 just my thoughts.

You need to warp your ground around the pipe a bunch of times to get rid of the magnetic charge in the pipe .

Magnetism. We run into it once in awhile. Usually happens more when it starts getting colder at night and hotter in the day, towards fall time of the year. But magnetism is your culprit. A chain can fix it. There’s a couple other ways too.

@godwinwelding7172

9 ай бұрын

Yeah we have tried all kinds of old school myths with not much luck on magnetic pipe. I’ve just never seen it crack that far away from a weld before. Crazy stuff.

@RockinLOutfitters

9 ай бұрын

@@godwinwelding7172 there’s a bunch of stuff you could do. But that’s your culprit.

@acecoors

9 ай бұрын

@@godwinwelding7172have you tried running your root on AC? That’s the only way I’ve found that works consistently

6013 and an AC buzz box

Drill pipe. Heat it up, wrap leads around it. Either way it sucks.

@godwinwelding7172

6 ай бұрын

I agree

Adjust your flux capacitor ⚡️

@godwinwelding7172

2 ай бұрын

🤔 that’s a genius idea. Thanks!

Hydrogen, windy out ? 70 18 is all you need, tough man , happens to all of us at some point , do the best you can . It will work out .

@godwinwelding7172

7 ай бұрын

Thanks for the pep talk. We all need one from time to time. ✌️

Better to just cut the hole in the pipe instead of saddling

Drill stem pipe will always crack

😂😂😂 with all these professionally opinionated welder geniuses commenting on here….. not a single one of these bozos have any content to prove their big ol opinion. That’s what’s wrong with our country a bunch of know it all key board warriors. Much respect😎

@_hector__

6 ай бұрын

Thanks for providing your insightful advice

@fittergrips2010

4 ай бұрын

look up specs on the tensile strength of drill stem. it is a lot higher than the rods suggested . Rod has to fit the tensile strength and metal properties . then have weld procedures to fit

You could always purge it and tig it.

@brysonw1815

4 ай бұрын

Man would have to setup a whole umbrella and shit to tig outside , ain't nobody got time to block the wind from shielding gas , stick weld thay thing with 7018 and be done

Heat it up then weld it would help

@godwinwelding7172

8 ай бұрын

Well…. it was hot from me cutting it Pryor but I could have pre heated more I guess. I have figured out I think it’s a different kind of metal all around. It’s not rusty at all 🤔

@jimmiebowman2645

8 ай бұрын

No telling where the metal coming from now days good luck

Чем резали трубу ? Как вырезать такое седло в таком количестве ?

@godwinwelding7172

7 ай бұрын

I use my victor cutting torch. Using oxygen and acetylene as the fuel Thanks for watching

Interesting

@godwinwelding7172

8 ай бұрын

It’s kinda unpredictable using this old drill pipe. Some spots are magnetized real bad others not. Some spots are rusted and worn very thin others look brand new. Thanks for watching

I've never seen anything like that either maybe it's the pipe or the type of rod try a different rod on a few of them leave it for a couple hrs and see

@godwinwelding7172

10 ай бұрын

We always use 6010 and haven’t had any problems so far. This was weird because even the pipe cracked. It was very magnetized though. I wonder if that’s the problem? 🤔

@treetop5752

10 ай бұрын

​@godwinwelding7172 hey friend it's the pipe, you need to preheat

@godwinwelding7172

10 ай бұрын

@@treetop5752 thanks I will try that

@hubertrobinson8825

10 ай бұрын

@@treetop5752 OK there's always something odd with our welding jobs I thought maybe it was magnetic too

@treetop5752

10 ай бұрын

​@hubertrobinson8825 it will crack from being magnetic but usually IN THE WELD this looks like old drill pipe that has been hardened down hole

Drill Rods do That . I try to take all our old drill steel home and make things from it and re purpose it and it usually will crack .... Crazy I can beat it to hell in a Hole but I can't use it for anything else 😂.

@godwinwelding7172

7 ай бұрын

It’s really rare for me to run into anything breaking when I’m done lol. Thanks for watching

@cupwalker24.7

7 ай бұрын

Yeah man. Very puzzling to me ... I have been on both sides of the industry welding and drilling . So I get to see it actually happen .....and I absolutely despise welding any Drill steel. . Unless it's just hard facing or something . But if someone brings you a scrap pile of Drill steel I would run away in less its my own project for home .... And that's sad because it's such heavy wall and great steel for things l you would think 🤔 🤔but it doesn't have the same metallurgy i guess . It will look strong but a lot of it is Chinese so its to far gone ;)

@godwinwelding7172

7 ай бұрын

@@cupwalker24.7 yeah bud the pieces that cracked were not rusty at all and clean on the inside. 2 7/8” They had a slight coating on the outside that reminded me of galvanized but not quite as bad.

Drill stem Has a tensile strength over 100,000 psi. using a 11018 would help with a preheat over 212 f degrees . remember drill stem tensile strength can be higher Your weld metal tensile strength as a rule of thumb should be higher than your parent metal

@godwinwelding7172

4 ай бұрын

😎thanks for that information. Very helpful

@fittergrips2010

4 ай бұрын

can send you some specs if you want @@godwinwelding7172

Wrap your ground lead around your work

@godwinwelding7172

8 ай бұрын

Yes! That is something we do also.

@heftylefty4054

5 ай бұрын

Buncha know it alls

I think its the material you using I was kinda thinking maybe that could be 1 1/4 chrom or higher I don’t think it’s from being magnetized Though it will weld kinda wild, not wanting to tie in right and may leave porosity if it’s magnetized I think that material is not one hundred percent carbon steel You see chromo gotta be preheated and cooled slow by wrapping in with K-wool or some sort Or it will crack most definitely

@godwinwelding7172

8 ай бұрын

Yeah I think your right about that. It looks different from the other sticks

You werent holding your mouth right.

@heftylefty4054

5 ай бұрын

Hell yeah you already know!!😂

Stop using cellulose rods use low hydrogen

@godwinwelding7172

9 ай бұрын

In the last few cases it’s the pipe that cracks not the weld

@williamthomas9463

9 ай бұрын

That’s a crying shame but a 7018 might help sure enough because of having better elongation properties.

@heftylefty4054

5 ай бұрын

I can tell this guy Jason cousins 😂😢😅has never built a pipe fence from old used drill stem.