I have the same table with Pioneer 3700 Amp and also own 2 sets of Dynaco A25 and love them, also have A30, vintage audio is the way

Just finished refurbishment of one of these, new belt, cleaned and oiled. Different cartridge, mine has an ortofon OM10. Sounds excellent.

@Thirdfish

3 жыл бұрын

I'll ask you too. Inherited the Pioneer PL-120 in good condition too, but it runs a tad over 33/3 and 45, new belt too, cleaned the capstan with Isopropyl Alcohol and it hasn't altered at all. Is there a screw or something to tweak the belt speeds? Be a shame not to have it playing again.

No surprise there are still PL-12D's out there. They made and sold SO many of these tables between 1973 and 1975...they were the Toyota Camry of turntables. When you walked into Pacific Stereo in California, they would have these stacked up at the door. Buy a Receiver and speakers, get the $99.00 PL-12D for free...

@braindeadtoo

6 ай бұрын

I bought mine in '74 for £36 in London. No free offers:o(. They were excellent decks, especially when compared to what was on offer by British manufacturers at a similar price.

@joey1127

6 ай бұрын

@@braindeadtoo Heck yes. Same in the States. Over here, they were a budget wonder table. When you lusted after a Thorens, Dual, or Linn but you only had $100 for a turntable, the PL-12D was a given. As I said, at Pacific Stereo, they would give you a PL-12D when you bought a Receiver and Speakers. When the PL-12D II came out and the price went to $120, it kinda lost it luster over here...the PL-10 was introduced at that time as the NEW $100 table...but wasn't as good as the original 12-D.

Thank you for this. Picking up one of these tomorrow and it's nice to know what I'm dealing with before hand.

@kendrickbyron9116

3 жыл бұрын

Dunno if you guys gives a damn but if you guys are stoned like me during the covid times then you can watch pretty much all the latest movies and series on instaflixxer. Have been binge watching with my girlfriend for the last days =)

@kingstoncristiano5837

3 жыл бұрын

@Kendrick Byron yea, I have been using InstaFlixxer for years myself =)

@rubenbrixton620

3 жыл бұрын

@Kendrick Byron yea, been using instaflixxer for years myself =)

Thanks man 👍 that was super helpful.

I love this TT. My only problem is I can hear the motor through my speakers. I already took it apart and and cleaned it and lubed it but it's still noticable. My only guess is I have to replace the foam inside

@braindeadtoo

Жыл бұрын

Hi, have you taken out the transport screws that fix the deck to the base? The deck should spring up and down when you push on it.

Hi I've just bought a pioneer pl12-d and what amplifier would you recommend to pair it with? Thanks:)

@braindeadtoo

7 ай бұрын

Assuming you have a moving magnet cartridge installed, any amp with a phono input will work. I used a Trio KA2000A with mine, which sounded great with my B&W D5 speakers, however it was only 16W per channel. If you're looking for a second hand amp, Rotel, NAD, Arcam, Cambridge all do decent amps.

Could you show how to balance the arm? Thank You

@braindeadtoo

3 жыл бұрын

Sorry I no longer have the PL12D. However here is a good vid that shows how to balance your arm. kzread.info/dash/bejne/daKnza5xgMicls4.html I hope this helps.

Inherited the Pioneer PL-120 in good condition too, but it runs a tad over 33/3 and 45, new belt too, cleaned the capstan with Isopropyl Alcohol and it hasn't altered at all. Is there a screw or something to tweak the belt speeds? Be a shame not to have it playing again.

@braindeadtoo

3 жыл бұрын

No adjustment to my knowledge. The deck comes with two capstans, for 50Hz and 60Hz power supplies. Maybe you don't have the correct one fitted for your country?

Hello, what is the size of the platter drive belt for this turntable?

@braindeadtoo

Жыл бұрын

I'm sorry, I don't remember. I searched on ebay for PL12D replacement belt and they sent me the correct one.

I have a pl12 motor works fine but I have a lot of noise when I connect it to the speakers any idea why? I changed the cables, I connected gnd, changed outlets, rotated the power cord on outlet. Does the earth wire needs to be connected to the outlet wire?

@braindeadtoo

3 ай бұрын

The earth wire must be connected to the earth terminal on your amp. If there is no terminal, them place it inder a screw that holds on the case. Make sure you scrape of any paint that might be under the spade connector.

@miguelmacedo935

3 ай бұрын

@@braindeadtoo I have both a preamp and active speakers do I need to connect the gnd wire to the speakers as well?

@braindeadtoo

3 ай бұрын

@@miguelmacedo935 that's a question I can't answer. I've only used a record deck with an amp and passive speakers. Do you get any noise when the preamp is connected to the speakers with the deck disconnected? If you don't, then hopefully you only need to connect the earth to the preamp.

I noticed on the net that some models have red and white cables, what would they be?

@braindeadtoo

2 жыл бұрын

Probably because they are mk1s. If there's a handle on the front of the dust cover, it's a mk1. A mk2 has no such handle.

@salvatore4388

2 жыл бұрын

@@braindeadtoo in the end I got it mk1 with the handle and red and white cables ... it's unique, and I'm satisfied with it. now just to complete it I would like to look for the arm with the brush that is mounted at the top left of the plate

@braindeadtoo

2 жыл бұрын

@@salvatore4388 I've never seen this on a Pioneer PL12D. Maybe it was a headshell from a different manufacturer. BTW it is generally thought that the headshell should be as light and rigid as possible, so adding a brush is not such a good idea. For this reason, some people also remove the handle. I used to have a lightweight SME headshell on my deck.

What do you use to lubricate the center stick where the platter is turning? :)

@braindeadtoo

4 жыл бұрын

I use 3 in 1 multi purpose oil.

@KeyzerSoze99

3 жыл бұрын

I've read sewing machine oil, but I couldn't get any, so I used oil designed for an electric hair trimmer. It came out fine.

@gimble8638

2 жыл бұрын

@@KeyzerSoze99 way better idea than 3 in 1, its way too thick and attracts too much atmospheric dirt

Did you sell it?

@braindeadtoo

4 жыл бұрын

Yes I did. Thank you for asking.

@coyote5.02

3 жыл бұрын

@@braindeadtoo mind if I ask how much.

@braindeadtoo

3 жыл бұрын

@@coyote5.02 £115 on ebay.

🤣🤣🤣

Nothing about the arm/tracking/anti skating!

@braindeadtoo

Жыл бұрын

Sorry about that. I never intended to keep this on KZread. I made the video, to assist whoever bought my deck assemble it correctly, after it was unpacked because I didn't have the original user manual. However, because it has had so many views, I guess it was a help, so I've left it on. I did not mention the setup of the arm and anti skating adjustments because they were already set up correctly.

I just bought this off of Craigslist list for 100 dollars. I hope I didn’t spend to much.

@braindeadtoo

3 жыл бұрын

I sold mine for £115 with the original box and packing. A dealer bought it, so I guess he was going to sell it on for more, so it looks like you got a good deal. BTW it cost me £36 in 1974

@coyote5.02

3 жыл бұрын

@@braindeadtoo wow

@Sladovsky1

Жыл бұрын

@@braindeadtoo The question is was it a lot back then? Ł36 now seems nothing, but back then?

@braindeadtoo

Жыл бұрын

@@Sladovsky1 that's about £400 in today's money, so a similar price to a good quality entry level deck today.

@Sladovsky1

Жыл бұрын

@@braindeadtoo Ł400 in today's money is quite a lot for a TT. You can get a very good quality entry level deck. I paid for my PL-12D last year about Ł60, but I bought a pre-owned original Pioneer headshell + brand new AT-VM95E cart with a stylus + a new belt + dust cover polishing cost +cleaning, lubrication, setting up everything correctly by myself. The parts + polishing were about another Ł60, so in total it was about Ł120.