Thank you for this instructional video! I just obtained one of these and had the same problem. I followed your instructions and it is running great. I do not restore professionally but like to try to bring them back to life and pass on the passion for vinyl to the next generation. Thank you again!

Gotta say: really appreciate that you left in the part where you put in the plate on the motor upside down. Very relatable and real!

I'm glad to see that you protected the tone arm during your repair.

@johnsweda2999

2 жыл бұрын

Yeah not good practice and he had the weight on

@PoppinWheeliez

2 жыл бұрын

This guy is a bit of a hack

@glenharrison8882

Жыл бұрын

@@PoppinWheeliez R.A.F

Thank You! The Pioneer PL-10 from 1968 needed '"Oil" at the right places! Your video was produced by a so-called experient expert! I understood and was able to follow step-by-step! Hurray - it's running with Beates and Stones from the sixties!

I had the PL-12D MK2 - basically a manual version of this turntable. I used a Shure M75ED cartridge which is a fairly compliant pickup as the tonearm is a good quality one. You're taliking early 1970s equipment here - the start of the era of great, well-built hifi from Japan. Your PL-15R is in terrific condition for it's age.

Great video! Thanks for the in depth guide. You explained everything you were doing and made it look very simple. Subscribed! Only down side is you forgot to replace the FOAM!!!!

@TurntableGuy

2 жыл бұрын

Yeah, I did it off camera.

@aerialplatforms2053

2 жыл бұрын

@@TurntableGuy What type glue would you recommend for the foam replacement? Thanks. Btw thanks again for your videos. Better than Xanax!

@TurntableGuy

2 жыл бұрын

@@aerialplatforms2053 As long as they're not putting you to sleep. lol. Just use a small dab of crazy glue. You're gluing foam to metal, so you want something that will hold.

@aerialplatforms2053

2 жыл бұрын

@@TurntableGuy No just relaxing! Thanks for the response. I was sure if it would eat the foam so now I know!

You are awesome and you make things so easy.

Don't know why you didn't remove the counterweight; can only stress arm bearings unnecessarily.

Well Done! Thank You

Very helpful.

Good job thanks l have the same problem l alrerdy know how to fix it thanks.

great vid and you did a thorough job, btw what brand/type of oil dd you use on the spindle bearing?

@TurntableGuy

3 жыл бұрын

Shell non-detergent 30 weight oil

at3600L is the best value cart on the market and is the same as a rega carbon. 99.9% alcohol removes old belts in seconds. I restore turntables daily. The microswitch is always dirty. Deoxit or open and clean. Motor bearings clean and lube. Also....belt drive tables are trash and AC sync motor tables without pitch control are by far the worst vintage tables. The main platter bearing is always gummy and dirty. Flush and relube. Whole process takes about an hour. 2 more to wet sand a polish the dust cover. Best part of this table is the look. When taking the motor apart, dont pry it. That is not good. Flush with alcohol while spinning the spindle. It will soften the petrified grease and release. Pry and pray is going to ruin the bearing.electronics stores sell swabs thst do not shed fibres. Qtip in a bearing will work, but risks leaving behind fibres that will negatively effect bearing performance. This guy is ok, but a bit ham fisted.

@TurntableGuy

2 жыл бұрын

Thanks for your opinions. I also restore turntables daily for the last 30 years. I have never had a stuck motor bearing before and can assure you that my prying was pretty gentle and did not ruin anything. But, you know, I'm rather "ham-fisted".

Thank you very much for the video, it was very didactic. I have a question, my PL15-R, sometimes, when it comes back the arm does not stop turning, which component is wrong and needs to be replaced?

I had the same problem but I fix it thanks to you now I got problem beacause stop doesn’t work any sugestions?please help

Please, what kind of oil do you use for the motor ? THX..

@TurntableGuy

2 жыл бұрын

3-in-1 electric motor oil

@benoitbrule1893

2 жыл бұрын

@@TurntableGuy Ok Thanks ! 😉👍

Hi. Done the same. But now the motor is stick he don't want turning and have a strange sound

@TurntableGuy

Жыл бұрын

Maybe you put the motor back together incorrectly?

No you should use grease on that type of bearing silicon carbide greece

@TurntableGuy

2 жыл бұрын

Thank you for your comment, but no, I disagree. We're not talking about an automotive bearing here that's spinning at 3000 rpm. With regular oil changes, that bearing will be quieter and smoother with the lubricant shown in the video.

Hello friend! the engine of my PL15R is weak. Did I find a new engine that works on my TT? I'm from Brasil.

you need to remove the rubber motor bushes and soak them in warm soapy water rinse them off and reinstall

@TurntableGuy

2 жыл бұрын

And why is that?

@4evaclapham

2 жыл бұрын

@@TurntableGuy if you do not know the answer to that then you are not a turntable guy

@TurntableGuy

2 жыл бұрын

@@4evaclapham Oh ok. 30 years experience, but you know better.