Part 1: 42RLE non VLP teardown. Removed from 2006 Jeep Wrangler 4.0L
Автокөліктер мен көлік құралдары
I have rebuilt several of these transmissions, yet this is the first time I have seen one behind the good ole 4.0L I6 engine. Most of them I have done were out of wranglers, yet had the 3.8L V6 engine. Interesting how they took the A606 and modified it for a RWD/4x4 platform. Note the many similarities, and subtle differences. Make sure to watch snapring locations!! Also save yourself a lot of headache and use your slide hammer and adapter for pump removal to remove the output shaft extension. And you're welcome. Ill do a case build-out, drum and pump, and Valve body vids on this as well. Note this is a non VLP transmission, the later I believe starting around 2007 had the gov pressure solenoid and transducer for main line pressure control.
Пікірлер: 33
Gosh.. I wish he would load the next videos in this series. He did such a great job on this one.
Where part 2? Best video I've found for this transmission. Thx for the video
@gunterding_performance9558
2 жыл бұрын
I have over a hundred I need to upload. Ill try and get to it
Love watching Journey men rip apart a transmission 🤙🏽🤙🏽tanks bra!
I have a 42RLE in my 2009 Challenge SE. Ive been having issues where its telling me it has an error immediately after shifting which i found is usually associated with a gear ratio error, which in my case is 3rd gear. So I believe it put itself into limp mode and will stall out at slow speeds (typically 30-35mph). Lots of what I read online pointed to the solenoid pack being the cuplrit when it starts to go bad so I decided I will do my first ever service on a transmission, only to pull the pan down and see large metal chunks of what appears to be a snap ring. Was super intimidated to even drop a trans but after seeing this im feeling much more confident
@gunterding_performance9558
Жыл бұрын
they are notorious for breaking snap rings! the drum is the only thing that is 'difficult'. as you pull a snap ring keep it with the plates and clutches it holds down. makes reassembly easier
Great video thank you so much for presenting this in the way that you did it seems to be old hat for you I've worked on a lot of manual transmissions mostly for race cars and most of that formula race cars and never really had a need to worry about automatic transmissions but as you get later in life you tend to want things easier in your day-to-day so automatic transmissions become more of a regular thing and with that the need for the knowledge... Thanks again
What happened to the rest of the video parts? Would much like to see the valve body tear down and the complete rebuild.
Great vid got all the info I need ! Gonna do a couple bong hits and crack my 42rle open !
Excellent video, really informative. To remove the front pump do you have to remove the valve body before?
@gunterding_performance9558
Жыл бұрын
No
I am presently having a lost of prime dtc for one of these transmission it will suddenly slips and vehicle will rev out as if in neutral. This only happens on a steep incline.One the flat there is no issue. Any idea what would cause that to happen? Thanks
Are you in Florida? I could go for some guidance.
Great tear down video, what's the status on the valve body and the rebuild video, getting ready to do this on my jeep
Have you ever dealt with code P1745 Line pressure too high too long
Hello dear man! I am writing to you from Russia. I have a Dodge Nitro 3.7L automatic transmission 42 rle. I lost reverse speed, sometimes it’s there, sometimes it’s not. please tell me what is the reason for the lack of speed? I will be very grateful to you.
Are you hiring for transmission rebuilder
I got a customer car in went into limp mode. Found someone installled 2005 rle withouth vlp into this 2010 chrysler 300 with vlp. Can i mod something to run it or is do i just tell this guy to buy another trans and have me install it.
My input shaft has play in the splines should I order both the shaft and the hub
@gunterding_performance9558
2 жыл бұрын
Thanks for question, and sorry for delay. Ive seen several with some play be normal. Unless excessive no concern.
Any opinion on just replacing the torque converter when the TCC code P0740 is caught early? I can diy the torque converter for about $150 and the transmission performs great otherwise.
@gunterding_performance9558
2 жыл бұрын
perhaps but the teflon seals are on the input shaft and seal of inside of stator, also if material from lock up clutch is shed will need to other unit issues.
@Matt-nq4du
2 жыл бұрын
@@gunterding_performance9558 Thanks for the info. The converter will be $150 since I can do it myself vs $2500-3000 for a rebuilt transmission. So I’m going to run it and see what happens haha
@gunterding_performance9558
2 жыл бұрын
@@Matt-nq4du worth a shot for sure
@Matt-nq4du
2 жыл бұрын
@@gunterding_performance9558 Well I installed the new converter and the shudder under moderate load in lockup is gone, now how long will she last is the question haha
@rudybishop9089
Жыл бұрын
@@Matt-nq4du keep laughing and keep hummer in’ it !
Hey, what is the part number of this transmission ?
@gunterding_performance9558
2 жыл бұрын
Dealer part number I am not sure. Sorry
Im getting a "p0706 transmission range sensor rationality" after rebuilding this tranny help!
They don't make transmissions like they used to.
@gunterding_performance9558
2 жыл бұрын
They surely do not! Thanks for comment
Just too annoying to watch with him comparing every nut and bolt to a 606. Who cares?