You got that right. People buy aftermarket parts and think they’re bolt n go. I learned the hard way, they’re for skilled installers to instal and look good. I have learned a lot recently and things are looking way better. Much thanks to Channels like yours.

Brother your skills shine! Love that you’re showing your work step by step. I’m learning new shit every time I watch one of your video’s . You a bad man!

@MakeItKustom

3 жыл бұрын

Thanks Christopher I appreciate the feedback!

Very good - thanks so much for sharing what might seem like a basic bit of knowledge! For DIY people it's something that doesn't get shown on TV or KZread.

A little tip. When aligned at factory, the rear end of the front piece should be some bit further out than the next piece behind the space between. This will prevent from windnoices. How much the "further out" depends on how wide the crack. A friend of mine worked at Volvo in Gothenburg painting. Before paint they checked the alignment. The space between panels and doors before were mostly quite accurate, but the "output" (lay down a ruler between the parts and one should be in air) on the backend of the fenders towards the doors not always... If even, it will occur a swirl in the crack between and this vibrates the panel in rear of it. Note that this output measures differ depending on where on a car. The air is passing the body slower when its in the back due to all whirls building requiring less and less "out" Good luck!

@MakeItKustom

2 жыл бұрын

Thanks for that interesting tip!

Everything you say in your videos makes sense. An amateur like me understand perfectly thanks to your way of explaining stuff. This is how they should teach metal work everywhere. 👌 🌟

@MakeItKustom

2 жыл бұрын

Thanks so much for your feedback!

Thank you for this TIP. It is an issue , that I had never seen addressed on any metal working / body work forum. I appreciate your expertise & abilities. Stay Real. Rick

@MakeItKustom

3 жыл бұрын

Thanks Rick I am also curious why it’s not more widely covered in fact until very recently I did not think that this was how bodies were lined up. When I had my eureka moment I thought man I bet a lot of people could benefit from this

Very clear explanation and demonstration Mike

@MakeItKustom

3 жыл бұрын

Thanks for the feedback mike!

Holy smokes, this is gold---the doors on my '48 DeSoto are completely misaligned. Some jackalope "fixed" the rh door misalignment by BENDING (smashing) the vertical edge of the door in, by at least 1/8 in. I was wondering how I'd go about fixing this. Thanks again for another super helpful video!

You certainly are the MAN! What great understanding and patience!

your in trouble for giving away the secrets.. LOL This is the first time I've ever seen a video on this. Great job. Keep it up.

@MakeItKustom

3 жыл бұрын

Haha I have no problem in sharing what I’ve learned. Sharing is caring! I’m happy to help. Glad you enjoyed the video!

First time I’ve seen it done. 👍

@MakeItKustom

3 жыл бұрын

That's awesome!

Grate demonstration on fixing uneven spaces with panels

So happy I found your channel.

spot on and much the same principle as still done in car plants all over the world. In some plants a tool called the 'Saarlouis Hammer' is used to 'whack' the corners and other troublesome spots back into shape....if you hunt around, the name might give you a clue as to which major OEM came up with that...

Great stuff. Working on a 67 mustang and almost ready to get the doors back in. This will be in my future!

I watched this the 1st time on Instagram, but now I've watched it again on KZread! And I don't even do bodywork!

@MakeItKustom

3 жыл бұрын

Haha right on! Thanks for supporting! 👊👊👊

Fantastic brother

Picked up another little diamond tip from you that I'll be using on my pickup, when I get to that point. Thanks again...

I use my slapper for a dolley often. Slappers have many jobs. Great video.

this was the first time i had heard about this. great explanation and how to. realy enjoying your videos. entertaining and educational thanks!

@MakeItKustom

3 жыл бұрын

Thanks so much! I’m glad that you found value in the video!

Great channel I've watched a bunch of your videos there is a lot of good info. People do need to be aware that doing this can sometimes cause a buckle at the end of the door. Another thing is don't be afraid to slice the panel next to it and but weld it in the right position. I'm sure you know this and it was not the right call for this job but sometimes it's required. I've done autobody since the late 80s. I've done a some chops, a rear wheel drive conversion swap, a sectioned car, a convertible conversion on a 40 Packard And a bunch of other stuff. Most of the cars I've cut were after the 60s so a lot of things are different to do than older ones.

GOOD TIP...I WILL USE THIS FOR SURE...

@MakeItKustom

3 жыл бұрын

Thanks man! Glad it was helpful!

Interesting tip this was a great learning experience. Thanks Karl

@MakeItKustom

3 жыл бұрын

You’re so welcome!

Great video. I'm doing a frame off on a 53 Chevy pickup. My first project on this level. Thanks.

@MakeItKustom

3 жыл бұрын

Thanks! That sounds like an awesome project! Good luck with your build! You got this 👊🏼

Just join been watching you for few episodes. Your explanation is very clear very nice way to explain the characteristic of metal during formation and assembly. Great video thank 😊

@MakeItKustom

3 жыл бұрын

I’m so glad you like it! Thank you very much cheers!

Good info! Thanks

You are a genius!!!

Awesome stuff

Awesome tips Thanks

@MakeItKustom

3 жыл бұрын

You’re most welcome thank you!

More solid tips bro great work

Thanks, you are a good teacher.

Crazy stuff brother. Love it. God bless.

@MakeItKustom

3 жыл бұрын

Thanks so much man cheers!

Excellent finesse-Thank you! ✅👍

Wow - seems so simple. This tip really opens my mind of what’s possible. 👍👍😎👍😎

@MakeItKustom

3 жыл бұрын

That's wicked!! Glad it was helpful

Now THAT will come in handy! Thanks.

@MakeItKustom

3 жыл бұрын

Some Bill glad to hear it!

Amazing and nice work, like always,

Excellent tip

Wow great trick, thanks for sharing your knowledge!

@MakeItKustom

3 жыл бұрын

You’re very welcome glad you liked it! Cheers

I am getting ready to start working on my Camaro. I have notice the passenger’s side door is like this! THANK YOU for showing me how to fix this!!

@MakeItKustom

3 жыл бұрын

You’re welcome Jim! Good luck with the repair cheers!

Great tip. Thank you.

Awesome video, very informative. Thank you

@MakeItKustom

3 жыл бұрын

You’re so welcome Mike I’m glad you liked it! Thanks for being here cheers

Great tip, thank you

Nice early hardtail z50!

Awesome, always wondered how this was done! Is it possible to, say, reduce the vertical gap between door skin and rear quarter. I just can't visualise how this would be possible without welding on additional material? 🍻 from Australia

@MakeItKustom

3 жыл бұрын

In many cases if the door gap is too wide for your liking and many people do this, add material to the edge of the door. All cars that you see with really tight super crisp door gaps have had this done

Great job! So much better than bondo. So many car restore videos even Foose spread bondo over every square inch and block it flat for days.

@MakeItKustom

2 жыл бұрын

Although all high end paint jobs get a complete coat of filler I do know exactly what you’re talking about one of the things I hate the most is seeing a car with obviously thick edges. It’s not necessary

3:37 I knew autobody guy every time he said he had to do a bump he ran to the bathroom. Now I know what he meant.

Thanks bro

Do you have a video of a quarter panel and trunk lid fitting

nice work. love your videos. too bad that many cars would be caked with 1/4" worth of bondo lol

im doing a 70 k5 Blazer thanks man!

@MakeItKustom

3 жыл бұрын

Welcome!!!

Awesome tips!

@MakeItKustom

3 жыл бұрын

Glad you like them!

Wow, great Job👌

@MakeItKustom

3 жыл бұрын

Thanks man!

I am wondering if I can do this to my 72 k5 without damaging the paint?

What can be done to fix a door that is sticking out too much? Like an 1/8th inch but the door hasnt been replaced. Is there a way to adjust that outside edge without hammering? Striker isn’t adjustable. Already tried that.

How do you do it the opposite way, where you have to move the skin inwards?

@michaelwillette5837

3 ай бұрын

I was going to ask this also ! ! Glad you did. @Makeitcustom - wish I would have found this video last weekend. I gave up on my door while putting a vehicle all back together. I'm going to try the reverse method for moving it inwards.

This is the most frustrating thing in the world.. how many restorations have you seen that have a somewhat lifted bonnet on one side or a door that doesn’t shut.. but it has a new paint job so fixing it is going to be impossible.. answer.. too many!

@BeefandEggs

22 күн бұрын

So it’s better the fix the panel gaps first and then paint the car?

another great tip thx

@MakeItKustom

3 жыл бұрын

You’re welcome and thank you very much for being here!

Nice work

@MakeItKustom

3 жыл бұрын

Thanks!

So what do you do when the door over exceeds the body frame it seems yours was the opposite

Cool build. You both get free tattoos for life. Nice job for both of you. Just an FYI note: when laying up sheet goods, you can place dowels between items that you are glueing. Position things the way you want them and one by one you can slide out the dowels. Voila. Ps. Nice tip about the silicone/bronze. Pps. Is that a BC lilt (accent) that I hear?

@MakeItKustom

3 жыл бұрын

Wow you were good with your accent identification! Yes we are from BC! Thank you very much for the tips cheers Andrew!

@Andrew-qo6br

3 жыл бұрын

@@MakeItKustom . When I was 18 (I'm 57 now) I spent the summer out in the boonies by Parson... 30 miles from Golden in BC. Certain words you use have "THAT" sound. You have some BC mannerisms too. I'm not crazy, my mother had me tested 🙂. Keep on keeping on. And to Christina, thank you. Karl is great BUT remember, he might be the head but you are the neck. Nothing can happen without you.

So the outer skin is just folded over the inner skin, then seam sealer? No welds? I have never skinned a door, work on hundreds as a tech. I have thick metal skin on my 1967 C10 and trying to fix panel gaps. I was lucky as the truck had very little rust and all of it was on the drivers side. I got a tough one though. The tailgate was destroyed so I got a GM certified (Not to fit) tailgate from a KC company, put it on and found later, the passengers side is 3/16” thicker on the top 7-8”. So it stick out, go inside the tail light pocket in the bed, it looks like new. I think it will have to split the top of the bedside inside the tail light pocket where the tailgate jamb is. Move it out to be flush then weld in a splice. Not only is this leave no room for bodywork, filler or a way to make it flat and look right, but makes me mad to mess up a clean in-damaged area. The bedside wraps around and spot welded with the tail light pocket stamped in it. I see no way to make the top of the tailgate thinner. Geeesh! This truck is for me. A daily driver that came here by my son, who wanted to pull at trailer to mow yards. I did engine stuff, electrical and welding. He was trying to do body work. I bought a lot of parts, then he gave up, give me the truck & walked away! At 13, I spent $150 for a 1965 C10 Apache. So first and last very close. 38+ years in a shop, 12 year on the family farm, but between elbows and back, forced into retirement. Thanks for the videos and info. ASE Master since 1978 - Retired

@MakeItKustom

3 жыл бұрын

Wow man the fitment of aftermarket panels never ceases to amaze me at how inconsistent they are! Sounds like you have a good idea on how to tackle the misalignment. Always a shame to have to cut up new parts but sometimes it’s the only way. Yes some outer skins are just folded around and not welded but not all. I have seen some that are spot welded into place as well. It’s best to clean them off and you will be able to visually see whether or not it is spot welded

@deankay4434

3 жыл бұрын

It truly is a crying shame to cut a perfect tail light pocket to fit the tailgate. Especially paying a lot plus shipping. I wouldn’t have bought it but for the “GM Certied” stamping advertisement from LMC out of KS City. They probably sell 100+ each year and I am stuck with mess. Oh well. As an old dude, I can appreciate the thought you put into your rat-rod-truck. Hard to describe, but your are celebrating the parts and prices that only a true automotive enthusiast could appreciate. Few know how magnetos work much less point and condenser. Nicely done and others have noticed. Remind me of the go-cart that came to our farm by cousins. A knitted rope wound on a pulley and open spring steel to flip to touch the spark plug for kill. I like the chain & sprockets used on the parking brake. It screams look at me for a minute to figure out how it works. They have “Trashing Bee’s” that show off huge steam driven monsters with 400 lb flywheels and hundreds show up for these week long events. It is like a kid in a candy shop as every moving part could kill you or pull your arm off in mid sentence. Held in summer in KS & Iowa. They are cool! Best of luck. DK, Omaha, NE.

My truck just came back from the body shop. The front grill, lights, bumper, and left fender were replaced. The problem I noticed the next day is the bumper is aligned flush to the outside of the fender flare on the right side but on the left it looks like they aligned it flush with the fender then put the flare on. It looks odd because it is in about a half inch more on the left side than the right. Is there a way to adjust this? Or not?

@megaman4201

2 жыл бұрын

No one would be able to accurately answer without looking at it. Your best bet is to take it back to the shop.

Looks good 👍

@MakeItKustom

3 жыл бұрын

Thanks Freddie!

I have a ripple dent about the size of two silver dollars in my 2013 GMC on the left rear panel. Since it is two layers , how do I repair it ?

@MakeItKustom

2 жыл бұрын

A body shop would use a dent puller There are many different kinds but a Uni spotter is pretty common you can look them up. Otherwise you would be separating the panel fixing it and reinstalling it

If you push it too far, can you knock it back using the same method? And is there a risk of damaging the paint if so?

@MakeItKustom

Жыл бұрын

You can move it around quite a bit without damaging paint. It’s crazy to see what the PDR guys can do. (Paint less dent repair)

Do we get to see more of the blazer

@MakeItKustom

3 жыл бұрын

Sorry man no more Jimmy in the shop

If you were ever in the military you will know what this is but you got to love those BCGs (Birth Control Glasses) like the ones issued to every private in Basic Training LOL

@MakeItKustom

3 жыл бұрын

HAHA we just call them 80s Perv glasses.

👍

Nice!

@MakeItKustom

3 жыл бұрын

Thanks!

I have a door gap that needs to go the other way. The door is stick out past the quarter panel.

@MakeItKustom

2 жыл бұрын

That’s a door adjustment for sure

@ajd5363

2 жыл бұрын

@@MakeItKustom I have it adjusted as much as I can at the striker and hinge. It lines up at the window and front fender but there is a section that is out from the rear quarter. I'm thinking I screwed up the dog leg repair or something is up with the door. Dude, I would love to send you a pic.

Apparently Ford forgot to do that on my SuperDuty as the stock panels look Horrible on my new truck.

What about when door sticks out too much. I.e the opposite of your problem?

@MakeItKustom

2 жыл бұрын

If that’s not adjustable in the door hinges then there is only so much you can do with the door edge but there should be a little bit that can be massaged in with the door edge but this is a tricky and careful thing because you don’t want to see the inside panel through the outer skin

@rezashefa2643

2 жыл бұрын

@@MakeItKustom i do fitment adjustments a bit different. In both cases i would play with the striker that the door latches to

No need to worry... Just the tip and only for a second...😇

👍👍👍

@MakeItKustom

3 жыл бұрын

🙏🙏🙏

Karl is on point with this one, but I can't help but point one thing out... When we get our i-car cert., they teach us about positive and negative fitment. As in, the fender to the door and the door to the quarter should all stick out a tiny bit to allow wind to flow over all panels and reduce wind noise in the vehicle at higher speeds. That's all. I'll shut up now.

Nice 1k 👍s up

Good Tip But You Didn't Show Fender Side!!

Fantastic tip, you make it look too easy though......

@MakeItKustom

3 жыл бұрын

It is a simple task if you know what you’re looking for!

👍👊

@MakeItKustom

3 жыл бұрын

Thanks Michael 🤙

Just a tip

Just the tip ha ha ha ha ha hahaha

@MakeItKustom

3 жыл бұрын

Ha ha Ha ha ha

Short and usefull! Thx a lot ... greatings from Germany BR ... Insta: 4x4mech

@MakeItKustom

3 жыл бұрын

Awesome! Greetings!