got issue with this few months ago- but found a way of preheating the engine and "forcing" it to eventually work using VCDS and output testing :) But eventually got sick of it and bought new part- this video made it child's play to change- enormous help! thank !!!!

Thanks for this! Was a big help. I have a 1.4 Golf TSI with the BMY engine. My car wouldn't rev past 3000 rpms. My error code was P10A0 and I replaced the air regulating module as per this video, problem fixed! One point, be very careful undoing the Torx bolts that hold the air intakes, very easy to drop them inside the engine, use a magnetic bit driver if possible. I think this job can be done in 1-2 hours by the average DIYer.

@gobyboby730

2 жыл бұрын

I have same problem will not rev past 3000 rpms but comes up with fuel pressure regulator

@Hass-Man

Жыл бұрын

I had the same P10A0 issue on my Tiguan wouldn’t go past 3000rpm stuck in limp mode and engine light on replaced this part went all away the power came back upon inspection the flap didn’t move as freely as the new one but no oil was inside as some forums stated.

@cstar4481

Жыл бұрын

@@Hass-Man part number?

@Hass-Man

Жыл бұрын

@@cstar4481 03C128063A 03C128063B not sure what the difference between both of these are but I ordered the one ending with A and it fitted perfectly and still working till today.

@inthecloudshash

Жыл бұрын

Replaced mine today, but keeps engine light on and in limp mode, do i need to do the basic settings allignment after putting in the new one?

Awesome tutorial, i'd enjoy watching a video on the signal inputs/outputs.Thanks for showing

This is absolutely brilliant mate. thank you very much

Thanks for the video, it was very informative. I bought the car from a dealership in the this state but it's also very intermittent(engine light disappears more than present) But I have experienced the loss of power just after 3000RPM (total loss of power) I think that i'll the error code read just to be extra sure that this might be my problem. Cheers for the video.

Thank you for the nice informative video. When i accelerate on to the highway it stutters in the 5th/6th en sometimes 7th gear. I think it is the throttle body. This video helps me to replace it thankyou!

@FourRingsAuto

4 жыл бұрын

Have you checked codes in VCDS? Might be worth checking misfire counters too.

@harwoods11

4 жыл бұрын

Yea.. Don't guess... Cost you far too much. I would check the charge valve on the turbo cos they fall apart. There is a modified version available now from Pierberg

Hi. Nice video. I need some help. My car has developed an error which is on VCDS intake manifold flap .. Bank 1… P2006….stuck closed. Car is 1.4 tsi 170bhp BLG engine. When engine warm , rev also goes up itself , seems like vacuum leak or faulty PCV valve .. any suggestions?? Thanks.

Cool stuff. thanks!

Thank you so much for the vid, ill definetely clean the flap even though now its summer the error has been gone. Do you know if the option to set the limits for the flap has been removed from some models? I have a 2012 variant cavd and under engine it shows me like 10 options compared to the 30 or so you got.

Thanks a lot for help. I think the gears in mine went. But the price of this part is WOW.

@FourRingsAuto

5 жыл бұрын

I know. Here in Australia it is like $500aud. Crazy money.

Finally, answers for my questions! I have one VW GOLF 1.4 TSI, 1k1 engine and at 3000 rpm i have no power at all, engine light lights up. Two years ago i changed the throtle body and the problem persisted. When i turn on the car it smells a lot of petrol and with the OBD tool i foun issue P10A4 and issue P2279. When i run the car i can ear a whissle, like loosing pressure from somewhere. I need to thank you a LOT because now i now where to dig in. Many thanks, once again, from Portugal. Can you tell me, if you know, what is the VW part number that i should to find out?

@quick-shift2446

4 жыл бұрын

Has it worked well for you

thanks for the video explanation. Its really difficult to find content/info for 1.4 tsi twin charged engine compared to ea888 engine.

@FourRingsAuto

4 жыл бұрын

Thanks for your feedback. I have added all the 1.4tsi videos to a playlist on this channel.

@DanielRevay

Жыл бұрын

@@FourRingsAuto thanks so much. I have twincharged 1.4 TSI BMY too. Great engine and great sounding too.

Replaced mine today, but keeps engine light on and in limp mode, do i need to do the basic settings allignment after putting in the new one?

I have this problem and got the new part today. If I just swap it over will it work ? I don’t know how to do the programming bit. Thanks

Good video, I’m subscribed 👍🇦🇺

Thanks for the video, can basic setting/adaptation be done with vag can pro? If so, can I know how its done?

Hey mate, Mine is doing the same thing. Is it meant to energise closed when you turn the key to ON?

Hey, Any assistance in resolving the P10A0 Electrical Malfunction Fault for the Regulating Flap? Flap was replaced twice, wiring to the flap checked, all was fine. I'm afraid the issue might be my ECU. Any guidance would be appreciated.

have a golf mk5 tsi 1.4 i change water pump but supercharger is not working i have a fault code p10ad .any suggestions?

Is it open before starting the engine? and close After running the engine؟؟ Or how this work.. after moving the car

Long shot question/confirmation. I’ve diagnosed mine as faulty as well, but I’m kind of worried if I swap it for the new one. That I have to calibrate/code the new one. What’s the process of this?

I have changed the flap but still the code appears does it have to do with faulty ecu or wiring parts? I need ur help

Which ignition coils do you use and why? And spark plugs also :D Ive got Oil in the air intake are, its not much and every 3 months I fill it up a bit, do you can Suggest what It can be? I already checked the turbo but there was nothing leaking, It comes from something further, I also checked the crankcase ventilation and it was okay...

What brand pod filter setup is that ? Looks good 👌

Hi there, Please could tell us if this valve should be closed when ignition on and off and only open up after 3k rpm. Does it need load to close or can you have car stood still?

@wiseguy0103

Жыл бұрын

I need the same answer for my Scirocco, won't come up above 3000rpm

Where did you find this wp intake ?

How long would it take to do this job?

всем привет хочу поделится своей радость наконец-то моя борьба с моим автомобилем закончилась целый год боролся я победил в 2015 году купил vw jetta 1.4 tsi 150 сил катался три года все было отлично пока не загорелся чек обороты не поднимались больше 3000 ( а должны в положении коробки Р до 4000) при резком нажатии педали газа скорость не поднималась выше 40км или 60 км поехал к знакомому диагносту результат ошибка (Р10А4 будь она не ладно я эту ошибку на всю жизнь запомнил) ошибка выскачила на пробеге около 50000км диагност предложил почистить дроссельную заслонку на впуске процедура точно такая же как рассказано выше процедура обошлась 2000-2500 т.р. собрали заслонку машина поехала как раньше на пробеге 58000км опять та же история та же ошибка (Р10А4 сука сколько она мне крови Выпила) принял решение заменить заслонка обошлась 15000т.р. поменял сам руки растут с того места подумал все но хрен там на пробеге 85000км как вы догадались Р10А4 мразь первая мысль продать нахрен машину и больше с вагом не связываться но здравый смысл взял верх дело оказалось ЧТО ВИНОВАТ( Клапан регулирование давление наддува) ЦЕНА ВОПРОСА 1600 РУБЛЕЙ ПОМЕНЯЛ САМ МАШИНА ЕДЕТ КАК РАНЬШЕ НОМЕР ЗАПЧАСТИ 03C906283B ПОСТАВИЛ НЕ ОРИГИНАЛ Pierburg 70258804050 ВСЕ ТЕПЕРЬ ОХРЕНЕНО ОБОРОТЫ ЕСТЬ РАЗГОН ЕСТЬ СКОРОСТЬ НАБИРАЕТ Я ЛЮБЛЮ СУКА ВАГ КОРОТКО ГОВОРЯ ЧИСТКА ПОМОГАЕТ ВРЕМЕННО МНЕ ПОМОГЛА НА 8000КМ ПОСЛЕ ЗАМЕНЫ ВСЕ БЫЛО ХОРОШО 23000 КМ ПОМЕНЯЛ КЛАПАН ВСЕ ТЕПЕРЬ КАК НАДО ПОСЛЕ ЗАМЕНЫ КЛАПАНА РАЗОБРАЛ ЕГО В НЕМ НИЧЕГО ЭЛЕКТРИЧЕСКОГО НЕТ ПОЭТОМУ ДИАГНОСТИКА ЕГО НЕ ПОКАЗЫВАЛА . ВСЕМ УДАЧИ НЕ ЛОМАЙТЕСЬ

I got a replacement a2c59511700 replacement. There is a sticker with a warning that it needs coding. I guess it's not a DIY change :( I have an ODBeleven can that code it?

Hi. I have a Seat ibiza 1.4 TSi 6j cupra, BocaNegrA version with 180hp. Original. I m doing the replacement of that throttle. But I also have to replace the other one behind . Exactly behind of that black plastic throttle, theres another metal throttle. So How can I differentiate the alignment from the plastic throttle to the metal throttle with VCDS and vagcom??

not having same issue but i thought it was the same, i got error code P2015 and it says something along the lines of "intake manifold runner position sensor/switch circuit range/performance bank 1a" im guessing now that it can be the intake manifold sensor next to the supercharger and i hope thats the problem because that is easier to fix than the other 3 sensors. Feel free to speculate with me about my problem, VW Golf 1.4 BMY 2008

PLEASE HELP ME IVE GOT A P2006 FAULT CODE “INTAKE MANIFOLD RUNNER CONTROLLER BANK 1” STUCK CLOSED. ANY HELP ??!!!!

Does it cause smoking from the exhaust?

I tried benchmark coil packs and one caught fire. Are the R8 longer than the standard ones and how do you know what which wires to change around in the plugin connectors (female). Thanks

@FourRingsAuto

4 жыл бұрын

R8 and 2.0tsi coils are longer. You would need to know the way each is wired with a wiring diagram and then change the pins over. It's something i'm considering doing a video on. I also have some Bentley Continental W12 coil packs that look similar in size to the 1.4tsi ones that I'd like to try also.

What group is this flap basic settings in vcds?

Hi...do you know the 5 wire pin out for the inlet air regulator flap. I strongly think my ecu is messed up

Hey mate changed mine as well did adaptation but car still doing the same thing not going over 3000

Doit on le programmer après son remplacement ?

Great

Is the static noise meant to stay on for longer than a minute? I have a TT 1.8T and it doesn't adapt for as long as my 1.4Tsi golf. The golf just electrically whines forever until I take the key out

@kostabizetic9353

10 ай бұрын

did you get an answer to this? also wondering the same thing.

Hello, You can help me with P0800 on a 1.4 gti. The engine is shaking and like misfire cilinder 1 also give a code p0101. I can’t drive normal anymore

good day These are my problems with limp mode/start stop error/engine light/epc light/taillight led gone 2674 - Angle Sensor 2 for Throttle (G188) P0222 00 [175] - Signal Too Low MIL ON - Confirmed - Tested Since Memory Clear 2676 - Angle Sensor 2 for Throttle (G188) P0221 00 [032] - Implausible Signal Intermittent - Not Confirmed - Tested Since Memory Clear 2761 - Throttle Actuator (J338) P1579 00 [096] - Adaptation Not Started Intermittent - Not Confirmed - Tested Since Memory Clear 2762 - Throttle Actuator (J338) P1564 00 [096] - Under-Voltage during Basic Setting Intermittent - Not Confirmed - Tested Since Memory Clear 20572 - Intake Air Temp. Sensor (G42) P0113 00 [237] - Signal too High MIL ON - Confirmed - Tested Since Memory Clear 4166 - Manifold Pressure / Boost Sensor (G31) P0238 00 [175] - Signal too High MIL ON - Confirmed - Tested Since Memory Clear

Vw 2012 went through water and is giving epc light when sudden acceleration is applied and not accelerating

Hello, your video is very helpful for me! I recently changed flap at dealer but still I have the same issue no power over 3000rpm. So, now I suspect wiring malfunction. Is there anything I can verify the problem? Also, what is the procedures changing wires?

@ExoticzJr

3 жыл бұрын

Same problem here me too after changge still doesnt work... Did u already normally ur cars sir ?

@kobayashinaoki6088

3 жыл бұрын

Michael Ryan I get my car checked at dealer and somehow they bypassed some wires to make it right. But they said this was the malfunction they have seen. Sorry for not being much help

@ExoticzJr

3 жыл бұрын

@@kobayashinaoki6088 lastes diagnosis the mechanic say the troble is in eccu lol... Eror p10a0 need to changge eccu for fix it ???

@kobayashinaoki6088

3 жыл бұрын

Michael Ryan I am not 100% sure but the same error code. When I asked another dealer to check my car, he said misfiring is happening and needs to change #3 plug and coil. Hope your problem fixed!

@victorbalboa7301

2 жыл бұрын

@@kobayashinaoki6088 reported missfire on cylinder 3 seems to be a common issue with this engine

HI did you do a video of dismantle /repair of the unit?

@FourRingsAuto

4 жыл бұрын

Yep. Look through my videos. Called the fault code with "fixed for free"

Would standard packs make the engine a bit rough at idle. Not bad but little sputter here and there???

@FourRingsAuto

4 жыл бұрын

Possibly, but so could things like carbon clogged inlet ports, or dirty injectors.

I have this same issue haven't diagnosed it yet but it's intermittent would it require a new flap?

@FourRingsAuto

5 жыл бұрын

Best thing would be to read the codes. If the P10A4 fault is there, then it's likely you need to replace the flap. Of course, I'd recommend checking the wiring is ok. If the issue is no power below 3000rpm, then you may have an issue with the supercharger clutch on the water pump.

@2trilltochill

5 жыл бұрын

@@FourRingsAuto I have power up to 3000 and that could showed up with descriptor actuation regulating flapper intake air electronic malfunction

@FourRingsAuto

5 жыл бұрын

@@2trilltochill remove the flap and turn on the ignition. If it doesn't move properly it's likely that it needs replacement.

My car goes over 3000rpm but feels like there’s no power/ turbo engagement .. could this part be the issue still?

@toccoultra

8 ай бұрын

Yes thats the issue.

Hi I’ve had my air regulator replaced came back with fault then guy said was full of oil. He replaced again and now I’m getting same fault. So with out checking he’s saying motor on way out but car doesn’t blow smoke plus I only on 100’000kms. Is it possible he given me another faulty air regulator???

@FourRingsAuto

Жыл бұрын

Sounds like you need a new mechanic as the first step here!

Hi, you know how u say it needs calibrating, how do i do that? Where do i put that 15:35 setting in to? Thanks in advance

@FourRingsAuto

5 жыл бұрын

You need VCDS from ross tech or a similar capable obd tool.

@effdon642

5 жыл бұрын

I have someone with VCDS but he asked me to ask u what he needs to do

Howsit mate, please can you assist me with telling me where i can locate my map sensor on 1.4 tsi GTI DSG CTH engine. Please please

I HAVE SOME problem. I HAVE Touran 2014 1.4tsi cng. My problem is P10a5 i chamge the flap but same problem i u can help me.. Position sensor in take air regulating flap Signal is too high

@Portuga_97TV_

3 жыл бұрын

Same problem, how do you resolve?

@deanpowell3341

Жыл бұрын

@@Portuga_97TV_ Me too! Did you solve it?

@Portuga_97TV_

Жыл бұрын

@@deanpowell3341 yes, in my case I changed the flap but the problem was still there. so I changed the part number 03C103175 and the air pressure sensor after the flap, recalibrated the flap and problem solved.

My car gave me a P10A0 code it’s electrical but there is nothing wrong with the harness itself , any suggestions??

@FourRingsAuto

3 жыл бұрын

Have you checked to see if it's full of oil?

@johnhorgan5313

Жыл бұрын

@@FourRingsAuto I also have P10A0, I have drilled the inlet regulating flap and cleaned with brake cleaner. It was not oily, but the brake cleaner came out black to start with. I tested the operation with obdeleven and the flap open and closed continuously, until I stopped the test. The mil only comes on occasionally, I am going to check the wiring to the ecu, do you have any other suggestions ? For example could an air leak cause this fault ? John

@briankibia6903

10 ай бұрын

​@@johnhorgan5313 did you get to solve it

Hi, I have the exact same engine and I have noticed that sometimes the car has no power and will not rev above 3000 rpm! Do you know what the problem could be?????

@FourRingsAuto

4 жыл бұрын

I have various videos on the 1.4tsi that discuss this.

@FourRingsAuto

4 жыл бұрын

Check out my playlist 1.4tsi common problems.

I have problem with this flap, after replacing the flap still the same, do you have the the solutions?

@D3nn1s

2 жыл бұрын

Any updates? Also did you programm the new flap and clear the error codes?

What should the flap do if I turn the ignition on? In the video he shows that it doesn't moves but should it move on a working flap?

@neyem9656

4 ай бұрын

Dis you have the answer ? I have the same error code

Is this the throttle body?

Bu parça p2004 hatası verirmi

Can this stop the car from start

Can you do the settings with vsds lite?

@FourRingsAuto

4 жыл бұрын

I haven't used the lite version, only the full.

hi i have same issues but my car is 1.4 golf mk7 tsi i dont see this unit on the car or has it been moved same same issues as you described on all other videos i checked throttle body, pedal sensors car goes to limp mode as soon as it reaches operating temperature before that its all fine

@FourRingsAuto

3 жыл бұрын

Different engine in the mk7

@yongamasotondoshe7518

3 жыл бұрын

@@FourRingsAuto any ideas how i can solve my problem prior to this the error that came was my LED tail light left outer failure i am not sure if changing these can solve this. i checked Throttle body, gas pedal and oil separator no issues now i am stuck

@FourRingsAuto

3 жыл бұрын

@@yongamasotondoshe7518 fault codes?

@yongamasotondoshe7518

3 жыл бұрын

@@FourRingsAuto i get the P codes around actuator sensor problem i will have to look it up in the morning and save the data

@yongamasotondoshe7518

3 жыл бұрын

@@FourRingsAuto maybi please have you email to send scan results

Where can I purchase one

I have replaced the air intake regulator flap but I have the issue, the light remain and no going over 3000 rpm

@abisekchand392

Жыл бұрын

How did you fix it

Hi guys. Hope everyone is well. I'm having an issue with my Polo gti Cav 2014 cthe. It has a low idle. Start up 1000rpm then after 30 seconds or soo 700rpm. Slight engine vibration due to lack of rpm. Also a stutter when giving it gas. Any ideas? I changed the battery and sparl plugs. Thanks in advance.

@benaves3462

7 ай бұрын

My scirocco with the same engine also idles at 700 is that not normal for these?

@nashlingovender1992

7 ай бұрын

@@benaves3462 Howsit bud. I have seen a few other vehicles with the 700rpm. Seems normal. I ended up selling the car about 3 months ago.

would this cause power loss my golf feels like 120 hp instead of 170

@D3nn1s

2 жыл бұрын

I guess only if the flap were stuck in the closed position. What was the issue?

Can you help me and tell me the Serial number for golf mk5 1.4 tsi? Thanks for help

@FourRingsAuto

5 жыл бұрын

Serial number? Do you mean part number?

which version of VCDS has this adaptation info?

@FourRingsAuto

4 жыл бұрын

Not sure what you mean. If you have a genuine vcds cable you should be able to do this.

@moldovanstefan1219

4 жыл бұрын

@@FourRingsAuto theres are people ....how have ..can protocol ...like me .i have golf 6 tsi 1.4 2009 year ...this car not support uds protocol . only can ....and we don't have in basic setting that list ....only group ... if someoane know the group for calibrating flap compressor please ...tll us

Hi got the part and changed it out not to difficult job to do. just one question I there was an oil residue in the vale not a lot but you can feel there is oil. what does it mean?

@FourRingsAuto

5 жыл бұрын

The oil is from the breather system. The intake manifold usually has oil in it too. Try taking the intercooler hoses off to see if you can drain any oil off from there as it's the lowest point. Does your car burn oil? These engines were known to have issues of using too much oil.

@gerhardkriel2179

5 жыл бұрын

@@FourRingsAutoAuto no not a lot of oil there is no smoke. it does use oil but not more than 500ml to 5000km.

@FourRingsAuto

5 жыл бұрын

Yeah don't worry about it Drain the intercooler.

@harwoods11

4 жыл бұрын

@@FourRingsAuto Do you not find that the turbo induction tends to drag oil through the intake system. I find this on most petrol and diesel turbos. Never a problem unless excessive obviously.

Alguna, puede decirme donde compro esa admisión?

Hello I have a 1.4 tsi 122 when the car gets hot it's turn off by its self and it's start one second then turn off can you help me ?

@FourRingsAuto

3 жыл бұрын

Have you checked codes

@djamel_bijoux

3 жыл бұрын

@@FourRingsAuto it's said low fuel pressure

@FourRingsAuto

3 жыл бұрын

Check fuel pressure from in tank pump and put the car under high load

What diagnostic cable, vcds version and security code

@FourRingsAuto

2 жыл бұрын

Genuine vcds

11:50 what's the beeping noise?

@FourRingsAuto

3 жыл бұрын

The ignition is on. The motor is duty cycle controlled. That's the sound of the motor on low duty cycle in its park position.

What coil packs do you use?

@FourRingsAuto

5 жыл бұрын

They are Okada Projects plasma direct coil packs. They are quite expensive though. They claim theu can output up to 4x the amount but not sure if it's proven or just marketing. I personally would put either 2.0T or R8 coil packs into it if it were my money doing it. These were in it when I bought the car (APR Stage 2) and I haven't had anything bad to say about them, just wouldn't pay the price over readily available parts from the VAG parts bin. To fit the 2.0 or r8 coils, the wiring plugs need a couple of the pins moving in the plug too.

@harwoods11

4 жыл бұрын

@@FourRingsAuto have you had your car remapped? I got my sons up to 210 on std injectors with good fuel mileage too. An incredible engine.

@FourRingsAuto

4 жыл бұрын

Stage 2 apr. 210bhp at the wheels.

@fionnan2811

4 жыл бұрын

Did you have problems with the standard coil packs. Mine keep failing 😩

@FourRingsAuto

4 жыл бұрын

@@fionnan2811 the car is running a lot more power and the standard coil packs are weak. You can also upgrade to 2.0tsi coil packs or r8 coils, and just have to change the pins on the wiring plugs around.

Best solution: remove and derivate de crancase ventilation to stop vapor oil in to admission air.

Same problem here but after i changge new one still dosnt work why... :(

@FourRingsAuto

3 жыл бұрын

What fault code

@ExoticzJr

3 жыл бұрын

@@FourRingsAuto p10a0 sir but after i changge on dealer VW still doesnt work still stuck on 3000rpm me use mk6 2011

@FourRingsAuto

3 жыл бұрын

P10a0 may be a wiring issue. It should be diagnosed correctly. The wiring needs to be checked when doing output test of the intake flap.

@ExoticzJr

3 жыл бұрын

@@FourRingsAuto i think input or output hv a damage bcause after changge newone its doesnt work normally... Bcause of that i back to use the oldone... Tommorow i will try scan and repair aggaint... Very thx for explaination sir :)

@FourRingsAuto

3 жыл бұрын

@@ExoticzJr have you tried to do basic settings or output test?

16 minutes of repeating himselves on how to take it off lol

en español por favor no entiendo nada