Outfitting Whitewater Canoe Bulkhead Saddles

In this video I go over the whole process and the tools used to outfit a factory Blackfly saddle.
Boat is an Octane 91
www.blackflycanoes.com

Пікірлер: 12

  • @andrewlederman4948
    @andrewlederman49486 жыл бұрын

    Loved this. Really helpful. About to outfit my first bulkead boat. Any tips on putting in a pump?

  • @SoffermanPerspective
    @SoffermanPerspective8 жыл бұрын

    Excellent man!

  • @williamkey9041
    @williamkey90416 жыл бұрын

    Thanks for the great vid! How do you like the 91?

  • @kendingsor

    @kendingsor

    5 жыл бұрын

    Sorry for the late resoonse, I love my 91!! Its my go to boat for most class IV-V. Being designed as a tandem (octane 92), it is a lot of boat to move around solo but for bigger folks (im 6'8") its great. It is insanely stable, surfs well, carves and holds a ferry, and is quite dry. It is such a barge, it is quite forgiving and as a result I have seen it cater to those with bad habits but that forgiveness can also be used as a tool and give you the confidence to work on the skills which may flip you in another boat if that makes sense.

  • @RobCassam
    @RobCassam5 жыл бұрын

    I have plenty of K1 experience and looking to get into a Blackfly. Is it possible to outfit this so that your knees have little pressure and the saddle seat is supporting all of your weight? (got bad knees)..

  • @kendingsor

    @kendingsor

    5 жыл бұрын

    That is the way any well outfitted bulkhead/saddle is. If you carve enough to get all of the way in you are sitting on the saddle in a kneeling position with your weight being on your butt and not your knees. Its not for everyone but a properly outfitted boat makes a big deal when it comes to c-boating and comfort.

  • @EjnerH1949
    @EjnerH19496 жыл бұрын

    What adhesive/glue/prep did you use to bond the ankle block mini cell to the plastic hull ? Thanks

  • @kendingsor

    @kendingsor

    6 жыл бұрын

    Einar Hansen I use the same weldwood red can contact cement with the same method shown for foam to foam. I just scuff up the plasric with some sandpaper and clean it good well with acetone or mek (gloves and respirator) before applying the contact cement.

  • @UguysRnuts
    @UguysRnuts3 жыл бұрын

    Your bread knife makes one helluva mess. Next time, try a Rapala filetting knife for carving foam. Keep spritzing it with water as you cut and you'll get a nice smooth surface.

  • @garry6954
    @garry69544 жыл бұрын

    Be careful not to be a Darwin award winner. Make sure you can escape a roll over!

  • @toddheil42

    @toddheil42

    3 жыл бұрын

    While these foam type pads were exactly what I was looking for, your comments just about brought about the "sweats". Certainly don't want the legs to get cramped up, fall asleep while in the midst of rapids, take a spill and get trapped. Gotta think this through.

  • @BlackflyCanoes

    @BlackflyCanoes

    3 жыл бұрын

    @@toddheil42 We've been outfitting our boats with bulkhead saddles for ten years and this has never happened to our knowledge. Most people find it harder to stay *in* the boat when they are upside down, falling out is much easier than you think. You can always contact us on Facebook to set up a demo so you can try it for yourself!