Thankyou! tore mine apart 2 years ago and for multiple reasons couldn't get back to it. This is extremely helpfull !

Very nice video. I was happy to see you convert it back to full time. I did the same thing to mine years ago and they definitely are nicer as full time. I kept good records of fuel consumption before and after and there was zero difference.

BRAVO. this is beyond helpful.

Thank you so much! Saved me some frustration and made reassembly much easier!

@derekdrivesdodge

2 жыл бұрын

Your welcome! Glad it helped!

Thanks for the video. Have a spare case and going to rebuild it just for fun and to have it ready to go. Definately will use the video to do it. Thanks

Man thanks a ton for this video. That was great!

@derekdrivesdodge

11 ай бұрын

Glad you liked it!

Gracias, no podía dejar de agradecerte está enseñanza

@derekdrivesdodge

Жыл бұрын

You’re welcome

just did mine with your video. Thanks!!

@derekdrivesdodge

11 ай бұрын

Glad it helped!

Great video!!!

Very nice video showing all the important aspects of reassembly.

@derekdrivesdodge

2 жыл бұрын

Thanks!

@jamesford2942

2 жыл бұрын

@@derekdrivesdodge I'm working on an NP203/NP205 6x6 transfer case. It will use the range box from the 203 mated to the 205. The input shaft of the 205 with be modified. I will use the intermediate 203 shaft and differential parts on the upper rear output. I will move the original 205 output to the lower side. The 205 gear will be driven by the upper chain shaft. It will take some custom machine work. I don't have a Dodge 203 yet so watching your video made things much more clear.

@jamesford2942

2 жыл бұрын

@@derekdrivesdodge does the range box share oil with the chain section on the original 203?

very helpful! thank you so much!

25:22 so those washers or whatever they are aren't needed when putting it back together with the stock full time differential? Or did you do some kind of measurement and determine that your particular application didn't need them? If so, how do you determine if you need them, and how many you need? Never done this before, complete start to finish videos of rebuilding the 203 are non existent, this is the closest one I've been able to find. Thanks for the upload.

Almost done putting mine together watching this video. Question, what were the torque specs when bolting it together? Thanks

Just went through my np203 but my shift linkage rod is extremely stiff, can’t even move it back and forth with a wrench. Any ideas?

does anyone know where the rectangle foam pad thing with the hole in the middle go? Mine fell out during disassembly and i don't remember where it came from.

Your video is gold man! One question though, on the output tail housing how do you keep the oil pump seal from popping out during installation?

Need a disassembly version

@derekdrivesdodge

11 ай бұрын

That seems to be the east part 😆

@davainemattis9743

4 ай бұрын

Right

I'm in the process of rebuilding my NP203 and your video is by far the most complete and informative. I think my case is missing the oil trough. Do you have any info on how it mounts? I might try to fabricate one. It just looks like a U shaped piece of sheetmetal.

@derekdrivesdodge

2 жыл бұрын

Hey, glad you liked the vid. I’m not professional for sure but it seems like a few people are finding it handy! I am not sure which trough you are referring to though.

What was the vendor you used for the rebuild kit and any other misc. Parts like a gear or shaft in need of replacing?

@derekdrivesdodge

3 жыл бұрын

I used a USA Standard Gear kit ZTBK203G. It does not come with the needle bearings for the differential and most thrust bearings/plates. Basically anything that did come with this kit I re-used or replaced with another unit I parted out. The one I was overhauling had the part-time kit installed and I swapped it out with a full-time diff I had from that unit. I didn’t source any other parts from a vendor, just parted out another one for this build.

Like the video most detailed one but out of curiosity are you putting any gasket sealant on your paper gaskets and if so what are you using?

@derekdrivesdodge

2 жыл бұрын

Just an oil is fine. I’ve been using an assembly lube with success but no sealant is required.

How do you clean it all up like that? Do you media blast it and paint? Also, what rebuild kit do you use?

@derekdrivesdodge

11 ай бұрын

I had it media blasted and the prime/paint like you would an engine. The kit I used was a USA Standard Gear kit ZTBK203G

Hi do you know if the input bearing and the output bearing can be replaced without disassemble the whole t-case? I think my bearings are already worn out Thanks in advance!

@derekdrivesdodge

2 жыл бұрын

I mean I’m not saying it’s impossible, but I don’t think I’d waste my time trying… you’d have to remove the whole T-Case from the vehicle to do the input anyway, so for the time it would take to overhaul…

Any idea how much different the NP203 is for a GM application?

@derekdrivesdodge

2 жыл бұрын

Honestly have no idea. I know that the input and shafts will have different spline counts so those wouldn’t cross. Subsequently the yokes should be different, otherwise internally it’s plausible that many of the parts could be similar. Guess I’ll have to get one and find out…

Hey Derek what brand/part# are those snap ring pliers? thanks

@derekdrivesdodge

11 ай бұрын

They are an OTC Horseshoe Snap Ring Pliers 714

I have a 1979 Chevy Blazer K5 and it has the NP203 transfer case, I want to change the transfer case oil but I can only see the fill bolt, do you know where the drain bolt is?

@derekdrivesdodge

3 жыл бұрын

There isn’t one on any I’ve seen and the two case halves prevent it all from coming out any one spot. The inspection plate cover on the ‘range case’ half can be removed to drain most. The magnet is right there too so that’s a good time to check that out. Those bolts pass through the case so removing just the lowest one will drain that half. Then the bolts that hold the retaining plate for the chain sprocket also pass through the case so the lowest one can be removed to drain the second case further. You won’t get it all, but if you let it sit a while you get enough out. Hope this helps.

@alannguyen5050

3 жыл бұрын

@@derekdrivesdodge thank you so much, and is the proper fluid 10w30 motor oil?

@derekdrivesdodge

3 жыл бұрын

Just a standard 30 weight motor oil is fine.

@clintpike9983

2 жыл бұрын

@@alannguyen5050 The GM book and Haynes books say use automatic transmission fluid for the NP203 transfer case

@alannguyen5050

2 жыл бұрын

@@clintpike9983 Intresting, when I drained it, the fluid looked exactly like motor oil.

What about chain stretch? Does anyone produce 2” 203 chain? Great video man

@derekdrivesdodge

2 жыл бұрын

I’ve just aways re-used the chain. I have not had any success finding new chains.

@mikelang8753

2 жыл бұрын

@@derekdrivesdodge BJs off road has them manufactured by a shop and sells them on their website. They are pricy but the only place you'll find new ones.

Do you have a recommendation on sourcing a new chain?

@derekdrivesdodge

3 жыл бұрын

Sorry, no. Last search I tried produced zero result and if they were avail they would have been 2-3 times the cost of an entire used case so it didn’t seem worth it.

@derekdrivesdodge

2 жыл бұрын

See previous comment reply…

@periodicallyred8849

2 жыл бұрын

Just started making them in the past few years: www.bjsoffroad.com/NP-203-Transfer-Case-Chain-ONLY-Made-in-USA-HV-005_p_2108.html