More 3d printed drones 😍

Thank you for this

this is exactly the type of build I've been hoping for idk why all the nano long range stuff is 18650 instead of 21700

@lililililililili8667

Жыл бұрын

just need that wokesnail whoop vtx to drop and I'll be in business

@Unboxingexperience7

Жыл бұрын

seems it will be heavy though - 1s 75mm whoop is at 39g. I suspect the VTX-camera-antenna set to be twice as heavy as HDZero at around 14g.

Impressive Nanolongrange design. Seeing used only ~500mAh to travel out 900m before turning around at 8:50. This suggests can travel 6-8 km on a flight.The constraint being video (antenna limitations)

@Unboxingexperience7

Жыл бұрын

yes, it is highly efficient. I get on my digital version +10km distance but 2.1km range

Very cool. I have a 2in quad I'd like to start doing micro LR with.

@Unboxingexperience7

7 ай бұрын

Go for it!

Is this Donauinsel in Vienna? Is flying there allowed?

Very nice! How is the ABS+ in terms of warping and strength? I considered buying it for my Cr 10 which doesnt have an enclosure, as they say that it warps less, but wasnt sure as they are basically no reviews on it.

@Unboxingexperience7

3 ай бұрын

ABS+ is superior to PLA+ and PLA. The latter warp after printing in sunlight and heat. ABS+ is warping during printing. I had no luck without enclosure so I used a blanket.

Do you have any issues with heat? having the fc/esc and the hdzero board close together without the heatsinks seems like that would get hot. On the other hand you dont have much blocking windflow so might be fine?

@Unboxingexperience7

Жыл бұрын

No problems so far except a broken cam without a crash. But I never used it in hot weather.

Hey, great job. Thank you for doing this. Is this version superior over the Nanolongrange_v2, or just different? If so, what are the poros/cons between the two?

@Unboxingexperience7

Жыл бұрын

V2 is lightweight and more compact. NLR35 is slightly bigger and beefier and, thus heavier. My top 3 pros for NLR35 are: Magnetic connectors are great, you don't need to weld/solder Liion batteries. GPS locks very fast due to different type and mount. Flexibility: props up/down, props up to 3.5", battery on top/bottom, FC top or bottom

@TechOffZedOn

Жыл бұрын

@@Unboxingexperience7 so the v2 has longer flight time?

@Unboxingexperience7

Жыл бұрын

didn't test endurance. probably slightly higher.

@TechOffZedOn

Жыл бұрын

@@Unboxingexperience7 Thanks :)

Is it too much to use 1303.5 motors on single 21700? Have you tested 3.5" biblade props (T3.5x2.2x2 HQprops)?

@Unboxingexperience7

Жыл бұрын

1303.5 with high kv around 11000 are perfect. The Hq biblades are drawing too much amps (>18A) and this setup was struggling. They might work on an ultralight carbon frame version. I guess a 3516 biblade would work fine.

Hdzero cam lens needs to be refocused. Cool video

@Unboxingexperience7

Жыл бұрын

thanks, will give it a try

@recifestargazer2192

Жыл бұрын

Any hint to focus it, @Ryan Quellet?

@thirtythreeeyes8624

Жыл бұрын

@@recifestargazer2192 Try a focus chart

@RyanQuellet

Жыл бұрын

@@recifestargazer2192 go outside and focus the lens on a far away object like the treeline

Hello Unboxing experience your name should be Experienced Builder!! with that out of the way just a question. Is the casing on the HD zero flight unit just for protection or is it also a Ihs? (heat shield)?

@Unboxingexperience7

24 күн бұрын

it primarily protects from physical damage

Needs a 2s version.

это маленькое чудо !

What are those magnetic connectors you are using for the battery?

@Unboxingexperience7

Жыл бұрын

It's in the thingiverse/printables deposit. 3d printed caps for 5x2mm magnets which push Nickel strips to the battery terminals. It's something I ve designed and tested.

@evren.builds

Жыл бұрын

@@Unboxingexperience7 thanks a ton ^^ great build :)

Truly amazing Bro. What motor kv did you use? Thanks. Might build too. In the hdzero build, did you have spare uart for the gps but intentionally not put?

@Unboxingexperience7

Жыл бұрын

11500kv. no there was no spare uart for gps... newer boards have spi elrs so you have 2 spare uarts. then gps will work too. I ll do an update with a fancy carbon version with gps hdzero/walksnail. so stay tuned!

@Unboxingexperience7

6 ай бұрын

11500kv. This was on an old board without a free uart. on the newer version I ve used a darwin aio with a free uart for gps

I was looking at the thingiverse page and saw that it was printed at 20% infill, why not higher? Too much weight?

@Unboxingexperience7

Жыл бұрын

yes.20% seems to be a good compromise between weight and robustness.

Might've lasted longer with the VTC6. About the same capacity but smaller and lighter.

@Unboxingexperience7

Жыл бұрын

I thought so too, but kzread.info/dash/bejne/i56M09Czp5fNodI.html New Molicel 21700s have even more power and capacity over the tested Samsung 40T. 21700 is the way to go.

Is this usable with all the parts from the nanolongrange v2?

@Unboxingexperience7

Жыл бұрын

yes, only the gps mount is for the smaller and lighter namelessrc tiny gps

that wiring is absolute chaos...

@Unboxingexperience7

6 ай бұрын

I reused parts from another drone

I really like your scale. What’s the name of it? I want same thing

@Unboxingexperience7

Жыл бұрын

look for coffee scale, it also got a timer. i found mine on aliexpress

How to fix the camera on the carbon fiber board

@Unboxingexperience7

Жыл бұрын

STLs will be released soon ;-) You can get a sneak peak on my instagram

whats the benifet of pusher vs puller drone?

@Unboxingexperience7

2 ай бұрын

I wanted to have the props out of view

@NRG_FPV-po4rx

2 ай бұрын

@@Unboxingexperience7 that makes sense

Hey men awesome video! Can I contact you for a scholar project for our students to involve them in electronics and drones? If we can get at least a little help will be great !

@Unboxingexperience7

Жыл бұрын

here is a bit more information www.instructables.com/NLR35-Single-21700-3d-Printed-Nanolongrange-Digita/ just ask if you need more details

@pedroazuajebolivar603

Жыл бұрын

@@Unboxingexperience7 thanks you For the respond! Hopefully I can make one to my own first!

what gps are you using?

@Unboxingexperience7

Жыл бұрын

NamelessRC tiny GPS

Which 3d printer is that?

@Unboxingexperience7

4 ай бұрын

VZbot 235

What motors?!

@Unboxingexperience7

Жыл бұрын

flywoo robo 1202.5 11000kv

What no GoPro? ;-)

@Unboxingexperience7

3 ай бұрын

been there, done that :-) kzread.info/dash/bejne/hHiAkpacfre4YMo.html

Hi how much does it cost

@Unboxingexperience7

Жыл бұрын

rough guess 150$ for the standalone drone without radio and FPV goggles

try to focus your camera

@Unboxingexperience7

Жыл бұрын

thanks, will do.

@user-tp3dg5ym6u

Жыл бұрын

@@dloc116 what do you mean?