I’m sure many people will find this video super useful. Thank you! 🎉

@bryansmith2479

Жыл бұрын

I did !

Nice Job, with you support I help someone else to get rid of 03 display pb. Mine is not a permanent one yet. And before ordering I would like to find a way to simulate a correct accelerator and see if everything else is correct. Thanks again.

Man thanks a lot for your video! I did a step by step replacing of the dashboard thanks to the tutorial 😊 Thanks a lot, keep doing such a great work!

This was excellent and super helpful. Thank you for taking the time to share your experience and knowledge. The 'string' trick was amazing. NIU should be paying you for this vid. All the best and thank you, thank you, thank you!

@Lantea13

Ай бұрын

You're very welcome, always happy to read that one of my videos helped someone out.

@Darkthunder5299

Ай бұрын

I have a problem if you can help I'd very much appreciate it! I also have the 03 code problem, I have also replaced the throttle. Yet I still cannot get out of e save mode. ( I bought it second hand in good condition and I also can't find the device on the app) I used it for a week and now it won't get out of E save. Any suggestions? @Lantea13

@Lantea13

Ай бұрын

@@Darkthunder5299 If the e-save mode is blinking, you need to turn off the dynamic mode in the app. Otherwise you should be able to switch between modes by pressing the button on the display. If you bought it second hand try and see if you can connect it in the NIU app to your NIU account, the previous owner should have removed it from their account before selling it. If they did not you need to contact them, if possible and ask them to do it, or you need to contact NIU with proof of purchase and they might be able to help.

@Darkthunder5299

Ай бұрын

@Lantea13 I appreciate the help, the issue with the app is, when I try to bind or connect the device it asks me to name it etc and I always get 1771 pop up. I wasn't using the app before and it worked fine. The e-save is not flashing, I just cannot get the e-save to go away when pressing the button. Thank you again for your help

I’ve been waiting for a do it yourself video thankyou!U r great instructed.

That's what I was looking for! THANKS

Thank you for doing this. I had this problem once already and got a warranty repair for it. However the throttle replaced by the warranty repair was defective too! Had to send it in again to get it fix!

@Lantea13

Жыл бұрын

That is unfortunate that even the replacement broke. Hopefully the next replacement is the new version where they fixed the problems that were resulting in some throttles failing.

Fixed mine thanks to you.

Best review ever thank you!

Awesome video, very helpful, you da Man 😊

thank you very much , also coincydently this video that help me fix my birthday gift from my mom was posted the day of my birthday LOL

Amazing tutorial, thanks!

Thank you!

Thank you 💞

Thank you!!!

Thanks you for this video, you save me

@Lantea13

Жыл бұрын

Your welcome. Happy you found it useful :)

Nice!

I freaked out when I got mine my ebike was stolen and this is my replacement. So I assemble it with out connecting the screen travel mode as they call it any ways figured it out love this thing I have the pro version.

I was hesitant to remove the display cover as I saw it was glued but I guess that's the only way to do it. Thanks for posting this

@Lantea13

Жыл бұрын

Yes, that is the only way. If you take your time and remove it carefully the double sided tape should stay intact so you can just stick it back on without having to replace it.

Nice guide! I did this today without the string, if you feed the clip into the handle you can use the brake wire to guide it in. Getting that grommet out was a huge pain.

To anyone who was foolish enough to not put a STRING through. Please, find a STRING thin enough to pull through with the old cable. Doing this with out one is... kind of a nightmare at the moment 😔

Nice videos. can you make a video in which you open the front light. to see how it's built inside? The background is that the outer light ring is deactivated in Germany. only the lamp in the middle lights up. maybe i just have to lay an additional cable to the control panel? Best regards

@Lantea13

Жыл бұрын

The wiring is likely identical and the light behaviour is set by the custom German firmware. But that is just my guess. I can look into it. Haven't considered disassembling the light, but if its not glued together I can give it a try. No promises :)

Hello..great videos. My NIU KQI3 pro power button stopped working. It won’t turn on the screen…do you have any idea for trouble shooting or fix on the issue. Would taking off the plastic cover be a good way to start? Thank you.

@Lantea13

Жыл бұрын

That is what I would try first to see if the button is broken or just jammed. But if your scooter is still under warranty I would suggest you first contact NIU support before trying a DIY fix. Edit: It can also be a controller issue if the button works but the scooter is not turning on. Best is to contact NIU for warranty repair.

I'm already planning ahead of when mine (which i havent even bought yet because I'm waiting for a sale 😂) breaks down some day. I've heard about some throttle issues but that doesnt seem that hard at all. I've dealt with worse with my previous cars and bikes 😂

@Lantea13

3 ай бұрын

The throttle change is a pretty simple process, so even if it does happen it should be an easy repair.

Hi! Thank you mate, you’re helping so much! I have a problem, though: in KQi3 cables near light are held by a rectangular plastic stuff. It seems it is fixed… any suggestions? Thanks a lot

@Lantea13

Жыл бұрын

Do you mean the rubber gasket the cables go through or the rubber 'cup' that holds all the cables together? Maybe if you upload a photo to imgur it would be easier to help.

@valentinonicastro1411

Жыл бұрын

@@Lantea13 Hey, thanks you SO MUCH for responding. I've found the only service manual and luckily they show this stuff.... anyway, without you I'd be in deep shit ahahaha thanks!!!! bye

@nickwachtel6969

5 ай бұрын

If you see this comment I have the same problem, how did you remove the rectanguar plastic plate that fixes the wires in place?@@valentinonicastro1411

Doing this tonight on my kqi 3, what double sided tape did u use to reseal? And is there a specific reseal process?

@Lantea13

Жыл бұрын

I used the original one as it survived the removal with just slight damage. To seal it back up I just pushed the cover back on, it has held fine ever since.

Come and do mine I tried something similar on another e scooter and bricked it. So now I'm happy with 32kms

Thank you for this great video. I have this error on my KQI3 as well but couldn't find where to get a replacement throttle. The global support wants to send my scooter in. Anyone has an idea where to get?

@Lantea13

Жыл бұрын

You can order spare parts from NIU service partner at shop.besender.com/store/ if the part you need is not listed fill out this form niu.besender.com/form and they will reply to you with the cost of the parts you need. If you are requesting parts under warranty, try and ask them to send you the part if you know how to do the repair yourself. NIU mentioned on reddit a while back that they should be willing to do that, if you can do the repair yourself. Not sure if their policy has changed since then.

Great video! I can't get my handlebar grip off. Did you just turn yours or was there anything else you did to get it off? Thanks!

@Lantea13

7 ай бұрын

Thanks. I just turned it as I was pulling it off. Takes a bit of effort but comes off in the end.

@jaredshein4424

7 ай бұрын

@@Lantea13 I got it off! Appreciate the response 🙏

I was wondering if this would also work on a KQI3 model, because mine also got a code 3.

@Lantea13

2 ай бұрын

Yes it should work on the KQi3 Pro as well, the process is nearly identical, there is just an extra rubber plug from some photos I have seen.

What size Allen wrench did you use to loosen the throttle? For some reason I can't get mine loose!

@Lantea13

Жыл бұрын

Allen #3; full list of tools used is in the description.

Hello! I loved this video and found it very helpful as I have recently come across an Error Code 03 because of my faulty throttle. Where did you get the replacement throttle for this scooter?

@Lantea13

Жыл бұрын

I got it from NIU. You should contact their customer support since your scooter is still under warranty. NIU have mentioned (here old.reddit.com/r/kqi3/comments/vzdnip/brand_new_kqi3_error_03_code_after_less_than_10km/ig7x23s/) that it should be possible to just request a spare part under warranty and do the repair yourself.

@nateflanders2949

Жыл бұрын

@@Lantea13 do you know the case if I didn't pay for a warranty?

@Lantea13

Жыл бұрын

Two year warranty is included in the price of the scooter. Disregarding that you should still contact NIU support and they should help you out if you prefer to buy a new throttle instead or a warranty claim. NIU said that in the future they want to have more parts available direct on their website, unfortunately for now the throttle is not available without contacting them first.

@sreejithsuresh

11 ай бұрын

After you got the new one with replacement, did you send the old one back.?

@omovivomo

11 ай бұрын

@@sreejithsuresh no need to do it.

Very helpful your video, How do I order the trotle part

@Lantea13

10 ай бұрын

You can order spare parts from NIU service partner at shop.besender.com/store/ if the part you need is not listed fill out this form niu.besender.com/form and they will reply to you with the cost of the parts you need.

Do you know what each of the serial bus/ports mean? I want to disable the E save mode so that I can use a custom mode without the police finding out

@Lantea13

10 ай бұрын

Sorry not sure how you could do such modifications. Also keep in mind that modifying the scooter and messing with the electonics or firmware outside their normal function will void your warranty.

Hi I was watching your video. Anyway on that red connector! On mine I happen to have the other red connector. Female and a male. Do I have to connect them together. By the way’ I’m trying to figure my KQi3 kickstart scooter pro. Anyway to make my case shorter. My son was trying some IDK 🤷🏼‍♂️ he calls it tricks. Since then the scooter is tricking me now it doesn’t work’ the two red dots’ the No.3 blinking also this (❗️) and the beeping sound always go (on) the minute I press power. And the scooter feels lock. It wouldn’t go’ if I try to move it all those red lights goes on again. Even if power is off. And by the way I decided to open it back up and disconnect all the wires. Anyway the lights on back snapped off and the wires r visible so I taped it up. I need that break light 4 safety. Anyway I would appreciate it if you could help me out. Thank you 🙏 for your video.

@Lantea13

5 ай бұрын

The red connector should be for the second brake lever, the KQi3 has two brakes so both connectors are used. The 03 blinking with !, means a problem with the throttle, you will need to get a new throttle and replace it as shown in the video; if you messed with the connectors check that you have everything connected correctly; if your scooter is still under warranty contact NIU for repair, or if you can do it yourself they can send you a replacement throttle. You can contact them on Global-Service@niu.com or by filling out a repair request and describe the problem you are having here niu.besender.com/ "two red dots" and "the scooter feels lock" That could mean that you have the scooter lock activated through the NIU mobile app, open the app and check if you can de-activate the scooter lock, see here for example kzread.info/dash/bejne/iKKDyJJuqbfNoKw.html "lights on back snapped off and the wires r visible so I taped it up. I need that break light 4 safety" You can order spare parts, in this case the back fender from NIU and replace the broken one. You can order spare parts from shop.besender.com/store/ or if they are not listed fill out the form here niu.besender.com/form and they should send you a quote for the spare parts you need. That is how I ordered some spare parts back in March 2023. Hope this helps.

Thank you for this videe ¨ help me plese recently received my kqi2 and already got the 12 error😢😢😢

@Lantea13

2 ай бұрын

Error 12 is a motor hall sensor fault, for that its best to contact NIU and let them sort it out under warranty.

Would my kqi2 pro be good if I bought and installed a new display board?

@Lantea13

8 ай бұрын

Depends on what is wrong with it. If your display if faulty then replacing it with a new one should help.

🤔I need help with my scooter I'm it shows two red barz square red barz on the front of the screen when I push it once it turns on and it shows that I've done everything I can't get into it or unlock it I mean it's all because I I had it locked through my app and instead of going to my app to going to my app instead I started pushing the button on it too many times and that's play somebody out there Help Me 🙏 truly yours John Landman thank you maybe

@Lantea13

4 ай бұрын

The only way to unlock the scooter when it shows the two red bars is to use the NIU app to unlock it. If that does not work NIU support might be able to help. But I am not aware of other way to unlock the scooter.

Hello, I absolutely need the replacement part, however the Niu service does not answer me, would you have a solution for me?

@Lantea13

Жыл бұрын

You can order spare parts from NIU service partner at shop.besender.com/store/ if the part you need is not listed fill out this form niu.besender.com/form and they will reply to you with the cost of the parts you need. When I filled out the form and needed a spare part that was not listed, they replied within 1-2 business days. Give that a try.

Hi! I recently received my kqi2 pro and I already got the 03 error after using it for a day sadly enough. I’m want to replace the throttle but I don’t want to contact NIU since they are gonna give me the bad quality throttle again. I was trying to look for some throttle on Amazon I’ve found some but I don’t know if they will be able to fit with the connector from the kqi2 pro. Could you please help me the find a throttle from Amazon that would fit the Kqi 2 pro

@Lantea13

6 ай бұрын

Sorry to hear you already had a throttle issue with your scooter. I would still advise you to contact NIU and get the free replacement throttle under warranty. If you want to try a different 3rd party throttle, take a look at these photos of the NIU throttle imgur.com/a/L4QkiBC the NIU throttle uses 3 wires, so in theory a throttle with similar 3 wire setup should work, but I have not tested any 3rd party throttles so other than that I can't guarantee which ones from Amazon would work and which would not.

@txmzy1893

6 ай бұрын

@@Lantea13 and do you maybe know what type throttle connection model it has?

@Lantea13

6 ай бұрын

@@txmzy1893 I believe the connector the throttle uses is HX20020-3P

Where did you buy the replacement throttle?

@Lantea13

Жыл бұрын

If you need a replacement throttle its best to contact NIU or their service partner besender for parts they don't yet have listed on their website. If your throttle broke it should be covered by your warranty. Just ask them if they could send you the replacement part, if you are comfortable replacing it yourself.

Hi sir. do you have idea what should i do if the battery on the display panel always says on full charge but the actual battery life on the app is half full? and even on charging mode, the battery more are not moving. Do you mind helping me? Thank you.

@jeromelitao0623

2 ай бұрын

Up

@Lantea13

2 ай бұрын

Hi, sorry for the late reply; that sounds like some sort of internal bug in the display; did you try to disconnect and reconnect the main display cable that runs through the stem? That might reset it, but if that does not help it might be best to contsct NIU and their technicins might have a solution.

@jeromelitao0623

2 ай бұрын

@@Lantea13 yup i did, but nothing happened. I tried to contact NIU and asking for refund.

where did you get the throttle from looking to order one

@Lantea13

Жыл бұрын

You can order spare parts from NIU service partner at shop.besender.com/store/ if the part you need is not listed fill out this form niu.besender.com/form and they will reply to you with the cost of the parts you need.

lots of people whining about this issue on KQI2, so I thought I would watch your video before mine actually broke. More serviceable then I thought. Wondering if I should just go ahead any buy one of these so I will have it when mine breaks? I have about 600KM on my scooter.

@Lantea13

6 ай бұрын

The throttle is a fairly cheap part, so its not a bad idea to have one just in case you need it. When I was ordering some other spare parts several months back I also decided to buy an extra throttle. If you use your scooter for commuting and can't afford downtime for service repairs, having few common spare parts on hand is a good idea in my opinion.

My throttle hard to pull anyway to make it softer?

@Lantea13

8 ай бұрын

You could try to spray some silicone lubricant on the side where the two halfs of the throttle slide on each other, it should help to lubricate the moving parts so they move easier.

my scooter doesnt turn on its been second time it happened..i sent it first time back to repair shop and it did it again after 2 months

@Lantea13

Жыл бұрын

Sorry to hear that. Luckily you have a two year warranty to rely on, so NIU should fix it for you, but I fully understand it is annoying having to send it in for repair and be without a scooter for some time.

looks like the Xiaomi Displays, i will tuning with Xiaomi Controller and their Display its only 40€ Can u please tell me the measurements of the display and controller?

@Lantea13

Жыл бұрын

The specifications of the display can be found on the spare parts page shop.besender.com/store/model/detail?id=41 it is the same size as the one on the KQi2. Dashboard: Weight (lb): 0.08 Long (in): 3.543 Width (in): 1.575 High (in): 0.787 As for the Controller: 9cm x 5.5cm x 3.5cm

Hi I had your same problem ( error 03 ) they sent me the piece and I tried to assemble it following your video step by step but the problem is that the display does not turn on. got to the point where you plugged the cable in to test if it worked before closing the display. I saw that yours had 3 charging notches, could it be that my display doesn't turn on because it's empty?

@Lantea13

Жыл бұрын

Hi, the three battery level dots just indicate how charged up the main scooter battery is; if your scooter battery was charged before the disassembly it should still be charged. If you had the battery fully depleted (which I doubt) you need to charge the scooter for it to turn on. The display does not have any battery inside it, its all powered by the main scooter battery. Check all the cable connections again and make sure everything is connected correctly and try again. If the scooter is charged and all the cables in the display are connected as shown it should work, if all you did is swap out the throttle. For quick reference you can also check the pics in my written guide here www.reddit.com/r/ElectricScooters/comments/y2w2gu/niu_kqi2_disassembly_and_repair_guide_for_the/ Let me know how it goes.

@yassinvegas7324

Жыл бұрын

@@Lantea13 I checked that the cables are placed correctly and the charger light is green but the display does not want to turn on. do you have instagram? So I'll send you a video and maybe you can help me. it would be of great help.

@yassinvegas7324

Жыл бұрын

@@Lantea13 you told me that the display doesn't have its own battery and is powered by the scooter's own battery. so could it be a battery problem? Would changing the display help?

@Lantea13

Жыл бұрын

@@yassinvegas7324 From what you said in your original message, you only had the error03, which is a throttle error. So if NIU sent you a new throttle and you replaced it without damaging any of the other wires, the scooter should work. Did you have any battery or other problems/errors before the error03? If not, and if all the wire connections are correctly connected it should work.

@yassinvegas7324

Жыл бұрын

@@Lantea13 no, only error 03, I've never encountered battery problems also because I just bought the scooter. I got it in september and used it for a month and a half. in mid-October I got error 03 on the display and I haven't used it since. the display was initially fine even before packing to ship. they had told me to send it to them then I had problems with the courier and they told me they would send me the piece. two days ago the piece arrived, I mounted it and I encountered this problem. maybe my only mistake was to verify that the display was fine before starting to take everything apart. so now I don't know if I caused the problem when I disassembled the display or it was already present.

How did you get the Replacement Throttle from NIU. They don't allow you to purchase parts from them directly. They make you go to the shop to have them repair the problem for you directly

@Lantea13

7 сағат бұрын

Last time I ordered parts was March 2023 from Besender in EU, had no problem ordering the spare parts I needed back then. Here is a guide from NIU on buying spare parts, that might help: "For the customer from the NA region, if you feel comfortable changing the spare part yourself, please follow the below-mentioned steps: 1. Please go to www.niu.com/us and scroll down to the bottom; 2. Click [After Sales] and follow the instructions on the pop-up window; 3. When you fill out the form, please fill out what spare parts and how many spare parts you need. 4. Select [Send you replacement parts] For the customers in the EU, if you are capable of repairing the kick-scooter by yourself, you can purchase the spare parts by referring the following steps: 1. Please visit niu.b2x.com/shop/ 2. Click the flag icon located at the upper right of the corner and select the region; 3. Select Your Model 4. Select the parts you need and confirm the quantity 5. Scroll down to the bottom and click the “Next”" source: www.reddit.com/r/kqi3/comments/1cqy7yt/comment/l3ytya6/

Where do you buy the throttle?

@Lantea13

Жыл бұрын

You can order spare parts from NIU service partner at shop.besender.com/store/ if the part you need is not listed fill out this form niu.besender.com/form and they will reply to you with the cost of the parts you need.

Hello Im getting '33' error code. Do you know what is that issues? TIA

@Lantea13

10 ай бұрын

Based on the KQi2 manual, error code 33 is a "Battery open-circuit or imbalance warning" and it advises you to contact NIU for support.

@user-jm3fb9yj1b

10 ай бұрын

@@Lantea13 thank you!

whats the loose red wire?

@Lantea13

7 ай бұрын

That wire is for the rear brake on scooters like the KQi3 that also use a rear brake.

What i can do ? My nqiu2 pro charge 30mn and stop charging, and don't turn on ? Pls help me

@Lantea13

6 ай бұрын

Sorry but I haven't come across this problem before, so not sure what might be causing the problem. Possibly a controller issue. Make sure your charger is correctly plugged in and undamaged. Best to contact NIU support as their technicians might know more on what is causing the problem and provide possible troubleshooting tips. You can contact NIU support on Global-Service@niu.com

@kaito529

6 ай бұрын

@@Lantea13 ok thx

I have a problem if anyone can help I'd very much appreciate it! I also have the 03 code problem, I have also replaced the throttle. Yet I still cannot get out of e save mode. ( I bought it second hand in good condition and I also can't find the device on the app) I used it for a week and now it won't get out of E save. Any suggestions? @Lantea

@Lantea13

Ай бұрын

If the e-save mode is blinking, you need to turn off the dynamic mode in the app. Otherwise you should be able to switch between modes by pressing the button on the display. If you bought it second hand try and see if you can connect it in the NIU app to your NIU account, the previous owner should have removed it from their account before selling it. If they did not you need to contact them, if possible and ask them to do it, or you need to contact NIU with proof of purchase and they might be able to help.

Where can i buy a new throttle

@Lantea13

16 күн бұрын

Here is a guide from NIU on buying spare parts: "For the customer from the NA region, if you feel comfortable changing the spare part yourself, please follow the below-mentioned steps: 1. Please go to www.niu.com/us and scroll down to the bottom; 2. Click [After Sales] and follow the instructions on the pop-up window; 3. When you fill out the form, please fill out what spare parts and how many spare parts you need. 4. Select [Send you replacement parts] For the customers in the EU, if you are capable of repairing the kick-scooter by yourself, you can purchase the spare parts by referring the following steps: 1. Please visit [niu.b2x.com/shop\] 2. Click the flag icon located at the upper right of the corner and select the region; 3. Select Your Model 4. Select the parts you need and confirm the quantity 5. Scroll down to the bottom and click the “Next”" source: www.reddit.com/r/kqi3/comments/1cqy7yt/comment/l3ytya6/

Please help me ❤❤where I can buy this!!!!!!!!!!!!!!!!! 🙏🙏🙏🙏🙏🙏🙏

@Lantea13

Жыл бұрын

You can order spare parts from NIU service partner at shop.besender.com/store/ if the part you need is not listed fill out this form niu.besender.com/form and they will reply to you with the cost of the parts you need.

Link to new throttle?

@Lantea13

2 ай бұрын

Go to niu.com on bbottom click after sales and select scooter ebike, click your region and it will direct you to a site where you can order spare parts;

Where can I buy the throttle?

@Lantea13

6 ай бұрын

You can order spare parts from shop.besender.com/store/ if the part you need is not listed fill out this form niu.besender.com/form and they will reply to you with the cost of the parts you need.

@jopie1147

6 ай бұрын

Thank you 🙏

Where can I find the vin number on these

@Lantea13

10 ай бұрын

The vin number is listed in the NIU app. It is also printed on the metal under the plastic deck cover.

@sweetdmtea

10 ай бұрын

@@Lantea13 I bought mine off someone who already connected their phone So I can't access the app. Was trynna fill out the thing on nius page for replacement parts or getting it fixed

@Lantea13

10 ай бұрын

Best and probably easiest thing would be to try and contact the seller and ask them to remove the scooter from their NIU account, I believe you can do that in the app. The only other option might be to contact NIU and if you have proof of purchase they might be able to help on their end, but thats a long shot.

I did same thing as u taught in video but it doesn't work

@Lantea13

6 ай бұрын

If you had an error 03 and replaced the throttle with a new one and connected all wires correctly, it should no longer show error 03 and work. What problem are you having? Still error 03 with the new throttle?

What website did you get there at throttle replacement

@Lantea13

Жыл бұрын

You can order it from shop.besender.com/store/ if its not listed you can try to contact them to ask about ordering it.

What kind f screw head is it?

@Lantea13

16 күн бұрын

Which one? I list the tools needed in the video description.

Is there any wire - to unlock the speed?

@Lantea13

Жыл бұрын

Not that I know of. On the NIU scooters it seems to be all software/firmware controlled, not a simple wire cut as on some other scooters that use the QS-S4 display/throttle.

Thank you for this because NIU customer service is horrible.

@Streamz_N_Dreamz

Жыл бұрын

Good to know I got this issue 3rd day of use

My dumbass pulled the string out and the new throttle connector got lost in the handlebars, took me near an hour to thread it through lol

3rd day of use and I got this error code wtf. I think it's a firmware issue or cpu error

@Lantea13

Жыл бұрын

Error 03 is a fault with the thumb throttle. You will need to get it replaced. Just contact NIU for warranty support and they should take care of it.

Wdf, Hi guys your Eng is F_ing shit but lovely, I really love it man it's funny Shit man. You guys Anderstan that it's normal to swear in ENG language. Lovely shit man Like always. thx 👍😊 more shit.....

Don't buy it for 600 euros thrown away....... In 6 months I have sent it 4 times to Germany for repair, they don't have points in Italy for repair. They don't speak Italian, but Italian money is convenient for them. Unreliable people and poor product. With the old xiaomi scooter, not all the failures I encountered on this scooter had happened to me. Bought on 11/26/2022 and in July 2023 it broke for the 4/5th time because in the last ticket, in addition to the second breakage of the ignition button, error 03 was added to the accelerator. Buy other brands.

@Lantea13

11 ай бұрын

Sorry to hear about the problems you had with your KQi2 scooter. Did NIU manage to fix it and do you have your scooter back? What were the other problems apart from the last one you mentioned with the error03 and power button?

@cristianocenedese

11 ай бұрын

@@Lantea13 The first failure after a month the rear wheel made a noise and stopped after a few meters. The second time it didn't charge the battery anymore. The third time, just returned from the repair, it didn't turn on because the switch failed. Last time I no longer sent the scooter but I always requested spare parts for the display with the switch and then the accelerator with which it gave the famous error 03. I hope to make it clear that it is not a serious and unreliable company. Greetings

@Lantea13

11 ай бұрын

After that many issues I completely understand the frustration. Maybe after the second problem they should have replaced the whole scooter, it seems like something went wrong during the QC on your unit or just really bad luck having that many problems with one scooter.

@cristianocenedese

11 ай бұрын

If it was a serious company, after the third time I send a vehicle to be repaired they would have returned it with a brand new. I have shipped the vehicle all the times to germany and wasted 2 months of time only in the shipments.