Get your AUXBEAM Panel Here: shrsl.com/3qdzv Use 12% Discount Code : DONS linktr.ee/donslife - Links to all of my products and discounts

As always, excellent step-by-step walkthrough as well as post install feature demonstration is greatly appreciated.

@Donslife

2 жыл бұрын

Glad you liked it. It takes a long time to film 😂

Nice Job, Don. I just bought this unit for my 2019 Tacoma. It arrives tomorrow and I wanted to jump right in cleaning up all the wiring that some unprofessional professionals left excessed of tangled up under my hood. I've watched a few of the tutorials/reviews for this product and found that yours was presented the clearest and most helpful. Thank you, sir.

@Donslife

Жыл бұрын

I appreciate the kind words

Oh yes! Finally a DIY channel with clean installs. Clear video quality and angles. Thank you for taking the time to do this. Gained a subscription 💥

@Donslife

2 жыл бұрын

Happy to be of service! Lots of videos over the past couple years. Hopefully they are getting better 😂

i install that in my truck 3yrs ago.it works and held up great...and i live in a cold and snowy area like you🤣👍❗

Don your incredibly smart!! All your work is impressive 👏 your a great DIY! 👍 thanks for your time chatting with me too!

@Donslife

2 жыл бұрын

Happy to help Chad!

Just got done putting this switch in a 2022 refresh with the Duramax. Everything is the same, except getting through the firewall was a pain in the butt. The air intake tubes block it. Removed the first elbow, and access was still tight, but I got it... if you remove the back part of the intake hose, it wouldn't be too bad, but that seemed like it would be more trouble than it was worth. Oh, and finding the wire was a little challenging in the cab. I don't know if the 2022s have more sound insulation, but I had to dig for it.

I made me some wheel lights out of a 5 gal bucket and the 5050 leds and they work perfectly

Thanks for this video, great install and demo, definitely a good investment to slowly add accessories to your vehicle, gonna do this on my 4R.

@Donslife

Жыл бұрын

It has been a great solution for me so far. Filled up 7/8 spots!

@edgards

Жыл бұрын

@@Donslife can you list all of those 7 items? Just to see the possibilities?

@Donslife

Жыл бұрын

Light Bar Light Bar DRL (White) Light Bar DRL (Amber) Rock Lights On Board Compressor Pod Lights Interior ambient LED lighting

@Donslife

Жыл бұрын

Videos for all of these on the channel

Great walk thru, appreciate it!

@Donslife

Жыл бұрын

Absolutely 👍🏼 Glad you like it

Great video, this honestly sold me on it.

@Donslife

Жыл бұрын

It made sense for me and has been working well

First Purchase HERE

@Donslife

2 жыл бұрын

The cord was long enough. The only cutting of wires was my light bar switch

Excellent video Don!

@Donslife

2 жыл бұрын

Thank you Paul!

Thanks for taking the time to go through the app. Many videos and still no one has demonstrated the app as clearly as you have. Is the app compatible with android auto? (Disregard, I now know you mean something like carlinkit.) Im looking for a replacement to the CTS2 powerswitch.

Nice option. I just had the OEM Up Fitter switches put in, but this looks like a cool option, too.

@Donslife

Жыл бұрын

Thanks. I have both now! No shortage of switches 😂

Hey Don. Betcha that truck will soon be able to make coffee in the AM before too long with all your DIY mods! Hahhaa...nice work (as always)

@Donslife

2 жыл бұрын

Great idea 💡!

Really smart, like got both standards buttons or the Bluetooth. Nice one thanks

@Donslife

2 жыл бұрын

I also like the dual functionality

We'll done video. Great production value

So I'm wondering if I can cut the switch controls off and tap my DRL so they can work automatically? Then make everything automatic except things like light bars that are not for road use! Maybe i just need to find a way to split or separate the switch controls wire. Great videos keep up the great work!

This really helped, you made a good video

@Donslife

Жыл бұрын

Glad you think so!

So, theoretically, would I be able to run this purely from my phone without installing the switch panel? I'm looking at getting these for my RHD Jeep so I can finally get some strobes on it, but not super keen on the idea of tearing the dash apart to run the wires. Great video, super informative!

Thank you for the video.

Great stuff thanks 👍 you said you were going to up a different light bar Which new light bar you going with ✌️🇨🇦

@Donslife

2 жыл бұрын

I am thinking the Strand 22” dual row with DRL. I haven’t ordered it yet, but I think that’s the one

hey man I install the same switch panel on my truck before but haven't done the add a fuse connection yet hopefully you can help me to which one I can use for the add a fuse. Thank you, Keep making great DIY videos for our trucks 👍

@Donslife

2 жыл бұрын

Send me an email with exactly what you are trying to do and maybe I can help

Hey Don, love all your vids and mods. Will this work just off the auxbeam phone app or infotainment screen without having to run the 8gang controller into the cab?

@Donslife

2 жыл бұрын

Thank you sir! Technically you could leave the control panel tucked away somewhere safely in the engine bay away from heat and moisture. Your phone app via Bluetooth would do the controlling. Personally I would find that inconvenient and would want the panel in the cab, even if you left it sitting in the glovebox or something. If you want to control it with your infotainment system, you’ll need something like my CarPlay AI box to control the Auxbeam switches.

A+ work as always! If mine wasnt a lease id consider doing alot of your mods. Have you considered installing the sierra sportsbar from the 16-19 all-terrains? I swapped mine over but on the x-31 package not the at4. Ive had many compliments and would def look good on the artic white!

@mr.workhardplayhard6550

2 жыл бұрын

What is this sportsbar you speak of? I have the same truck

@Juddmann007

2 жыл бұрын

Gm had a factory sportsbar they offered on the 16-19 all-terrainX packages. I kept mine when i sold the truck and put it on my next one which was the '21 new body style.

@Donslife

2 жыл бұрын

I have thought about a couple sport bars including the one you speak of. With my current box cover I just can do it. But I haven’t ruled it out

@Juddmann007

2 жыл бұрын

Box cover definitely wont work. I had to do a bit of modding to the tonneau cover to make things fit right. The factory covers will not fit either. Only certain aftermarket ones will work.

Great vid. Do you know the power the panel uses to operate itself? Like standby power when all the circuits are turned on but no accessories actually drawing power? I have a different panel that draws 1a constantly just to have switches in on position.It’s a bit of an issue and I need to find new panel. Thanks

Great video and clean installation. In regard to the compressor, how do you deflate/flate the tires pressure?

@Donslife

8 ай бұрын

Without an auxiliary tank it is slow, but possible: How to Install an Air Line in Your Truck! kzread.info/dash/bejne/hJyl1attfqaYorg.html

Just wanted to point out that there is also a firewall penetration on the pasenger side as well. Might be a little harder to access from inside the cab though depending on the size of your hands.

@Donslife

2 жыл бұрын

True! I used the passenger side one for my onboard compressor auxiliary circuit. Either route, I found them both difficult 😂

@Lonewolf_Will2024

10 ай бұрын

So, Don quick question, on the driver side, penetration can you give a little input how or what did you use to get it through the fire wall?

Don - loved the video and the step by step install directions. My AR-800 arrived yesterday and followed your video and the supplied installation brochure supplied by Auxbeam. Unfortunately, despite everything being hooked up correctly I cannot get the control box to turn on and illuminate. I tried to reach Auxbeam for assistance but to no avail, and they don't have any Q&A or Troubleshooting links on their website, or none that I could find. My 2016 Toyota Tundra has LOW PROFILE mini fuses, so I used the supplied fuse tap, which is designed for mini fuses, and replaced my 10 amp low profile mini ignition fuse with a 10 amp mini fuse. The supplied fuse tap seems to fit fine into my truck's fuse box, and even with replacing the truck's 10 amp low profile mini fuse with a 10 amp mini fuse the truck started up just fine. I haven't hooked up any accessories yet, but one would conclude the control box should display it is receiving power with or without any attached accessories. Do you think the issue is using a fuse tap with mini fuses instead of LOW PROFILE mini fuses? Any troubleshooting ideas?

@Donslife

Жыл бұрын

Sorry just saw this message. KZread flagged it as spam. Have you tried bridging the trigger wire to the main power lead just to test it out for power. That small trigger wire is on a two prong pin. Maybe the other side is live. Just making guesses in the dark

Prefer the replaceable relay version, easier troubleshooting. Also if relay fails you can swap positions to put the circuit back in operation. Relays fail, I like the option to replace. I would not like to replace the whole relay power unit because (one) potted relay failed. They should keep the previous (old) form factor and add the RGB/Blue-Tooth features. Don, great videos. Thank-you!

@Donslife

Жыл бұрын

Thanks for sharing! Weighing the pros and cons as you research what works best for your project makes sense

@tom73055

Жыл бұрын

I like how you responded to his video . Great to see someone thinks lie me . I also would like to know if this company will provide any help, customer support and is in the USA most importantly this system is not waterproof from what I can see I put my money on Finex 4200 mini controller made in the USA, they provide lighting equipment for fire, police and public safety

@tom73055

Жыл бұрын

Thanks buddy for your vid but I’m still looking for quality waterproof system

sweet video and after seeing some of the updates to the 8 gang panel I'm leaning towards it over the 6 gang, mainly the toggle/momentary mode selection and the slimmer fuse/relay box form factor (since it'll be going into a car). Thinking this is just the sort of thing to make installing various Leds and ambient lighting much easier (since I have yet to install any 12v accessories). I do wish there was a 3 way toggle switch option because for the front light bar I'd love to control it by being on/off/on w/high beams) but might need to wire that separately. One thing I was wondering is that when you were showing your compressor with the inline fuse you said you could replace the 20A auxpower box fuse with a 15A one and negate the need for the inline one. I thought replacing the fuses was not reccomended, did you end up doing that without any issues?

@Donslife

2 жыл бұрын

You can change the fuse ratings up to 30A per circuit, just don’t exceed 60A of draw at once.

@calebwooldridge242

2 жыл бұрын

@@Donslife okay cool, thanks for the quick reply bud. I just want to add a few things so 60A shouldn't be an issue. Having to run 3 less wires to toggles in the cabin will be awfully nice though 👌

You should add dual roof ditch lights next!

@Donslife

2 жыл бұрын

🤔

Great video instruction. I see that you connect the remote wire to the ignition. Does that mean you can only turn lights on when the ignition is in "on" position? If so, is there a way to bypass that and give you the ability to turn the lights on without turning on the ignition?

@Donslife

3 ай бұрын

This video should help: Adding a Wireless Remote For My Accessories! kzread.info/dash/bejne/k4prx9tuZJSblKw.html

I have a Auxbeam and a light bar just like that, I want to learn how to install but I’m having trouble. So I cut the wires like you did in min 14:22 but I don’t know hot to connect to the box which wire goes to negative and positive since it’s it has a red blue and white wire, it’s also a RC led light bar with DRL

This look identical to the non rgb non app version. I'm thinking maybe all that functionality is built into the switch itself. My biggest dislike is that it doesn't remember what's on when I turn the car back on. So DRL would be pointless to wire up since they'd have to be turned on every time. I actually mounted my switch to my GMRS radio's mount underneath it so it's kinda like a console of equipment. Love the auto dim feature, works very well. Hopefully this will hold up better than the junk wiring harnesses KC sent me with my lights. Corroded and burned at the relay since it was 1 wire in and 2 out to each 80 watt light. The outputs were fine but the input wire was just burnt.

Thank you for the quick reply. What did you do with the negative and/or ground? Did you just have to run it to one of the switches?

@Donslife

2 жыл бұрын

You can terminate them on the body/frame or the switch

Gained another subscription! I would be interested in knowing if the Ar-800 is still performing well after a few months now.

@Donslife

Жыл бұрын

Welcome! It absolutely is. I just wired up some more lighting in this video last week!

@Donslife

Жыл бұрын

kzread.info/dash/bejne/hXeczaeEXbXShag.html

I have the Chevy 1500. You used a existing fuse tap. Which fuse number would you recommend to tap into? Engine bay fuse number or passenger side fuse panel number?

Very cool!👍

@Donslife

2 жыл бұрын

Thanks, more to come!

Do you know if you are able to swap out the fuses to higher amp? Or is 30 max? Thanks for the great video

@Donslife

2 жыл бұрын

I am not sure. My assumption would be each circuit is up to 30Amp but don’t exceed 60Amps total running at the same time. You’d have to ask the manufacturer if you can go higher than 30amps on one circuit

Great vid! How are you running wires from the bed up to the engine compartment? Also, if you had a 3.0 you'd be lulling a reservoir out 🥴

@BSO_Actual

Жыл бұрын

Pulling*

@Donslife

Жыл бұрын

Thanks! The video showing wires run from the box is this one: Rock Lights - Full Install Tutorial - GMC Sierra AT4 - 8 Pod RGB AuxBeam kzread.info/dash/bejne/h4dhlo-Kk9PMh84.html

Great video! Quick question though. How do you connect to the app? I've been struggling.

@Donslife

Жыл бұрын

It works fine for me. Restart your phone and if that doesn’t work delete the app and try reinstall it?

Awesome job, can you turn on the lights with the app even if the truck is turned off?

@Donslife

Жыл бұрын

Yes if you wire it up that way. Here is a video where I can turn it on remotely too: Adding a Wireless Remote For My Accessories! kzread.info/dash/bejne/k4prx9tuZJSblKw.html

very good step by step explanation - question? the ignition/accessory switch wire - where would I connect it since I can't do your option where you spliced into a red wire? I have 2024 GMC Canyon elevation - please advise

@Donslife

28 күн бұрын

Heated seats circuit? I used my cooled seats for these things

great video

can you use the same button for toggling and pulsing without opening the app?

Hi, Don. Excellent channel. I am interested in the AR-820, but do not wish to mount switches in the truck. I have a 2023 Canyon Denali, with Google built into the infotainment enter. Do you know if the app could be downloaded to the truck, and I could control my accessories with the screen? Thanks

@Donslife

11 ай бұрын

Not that I know of

Nice install

@Donslife

Жыл бұрын

Glad you like it

Question. If the light bar has 2 color modes (amber and white) , would you need to wire them to separate switches? It looks like you did but wanted to confirm! Thank you. Great video looking to get one for my father in law

@Donslife

3 ай бұрын

Yes I have each DRL to their own dedicated switch

Hey Don, a little curious when you are speaking about the "App" and choosing the Colors. Are the Colors associated to the Buttons on the App or colors coming out of your Lightbar?

@Donslife

2 жыл бұрын

Strictly the look of the panel buttons can be changed with the APP

@markmanning5683

2 жыл бұрын

@@Donslife Thank you, Sir. Great Videos and modifications. Must be nice to be rich! Ha, Ha, Ha........

Good morning, For the wiring of the RC light bar. I notice u cap the red wire for the switch, at 14:29 of video {New Switch Panel Auxbeam AR-800} that being said..... you run the WHITE wire into the positive terminal using 30 amp location on AUX box and then the BLUE wire into positive terminal of next switch over ? Using the 30 amp switch right next to it ??? Lastly, do you connect the power leads that come with wiring harness for the light bar or just burying them ? Thanks Don J

I am loving this control panel. One question. Does anyone if it is possible to set the control to power on the last set accessories as soon as it powers up with the car? As it stands now, when you turn the car off, powering off the panel, next time you power the car on, you must press the main power button on the panel to activate it. I would like to set it to power on automatically with the car startup. Is this possible?

Clean! Been planning on the switch panel before I installed any auxiliary lights. Did you consider the switch-pros 9100?

@Donslife

2 жыл бұрын

I did! But $850+taxes in Canada is more than I am willing to spend

@saltlifechris3623

2 жыл бұрын

@@Donslife Damm that's steep... with the auxbeam can you run any lights with the ignition off? For example if I wanted to run some rocklights

@Donslife

2 жыл бұрын

@@saltlifechris3623 you could, but all of the connected devices would be ready to go and the panel would stay illuminated while standing by. You could add an inline switch or a trigger I suppose. I’d have to give it more thought. There are remotes you could use as a secondary power source to the panel. 🤔

@saltlifechris3623

2 жыл бұрын

@@Donslife great suggestion

@joshd7465

Жыл бұрын

@@saltlifechris3623 i ran mine to be hot at all times. I shoot commercial gear firework shows so i need the lights to run long lengths of time with the engine and ignition off. It works great, and if just the panel is illuminated it does not run the battery down

Why did you put a blank wire end on one of the three wires where you cut off the connector? Was the wire you blanked the illumination wire for the switch that normally connects to that lead?

@Donslife

2 жыл бұрын

Yes I believe so

Does this kit has the feature come in white?

Hi Thank you for the nice review Can I control the intensity of the lighting, make it dim or strong?

@Donslife

9 күн бұрын

No problem. Thanks for watching. This product doesn’t allow you to adjust the brightness of the connected devices.

@smile4ever363

9 күн бұрын

@@Donslife Mmmm Thanks 😊

Nice video! Does the controller lose memory of the switches that were on after an ignition cycle from on to off to on again? Engine cooling fan for example should have immediate power without having to turn a switch on each time you start the vehicle. Thanks in advance

@Donslife

2 жыл бұрын

When the ignition is turned off the devices it controls turn off too. When the first ignition is on again, the devices need to be turned back on manually but they will stay programmed as groups and/or pulse, toggle and momentarily mode if you set them up that way. I installed a remote control circuit with a diode so I can keep the switch on without starting the truck too.

@tjchini6368

Жыл бұрын

@@Donslife Could you do a video on that setup? I am wanting to have power without the truck being on but still want to have safeguards in place.

@Donslife

Жыл бұрын

Done : Adding a Wireless Remote For My Accessories! kzread.info/dash/bejne/k4prx9tuZJSblKw.html

Don, great work, Gained a subscriber! I'm curious if you know, I reached out to Auxbeam asking if you always had to turn the switch on (for a specific device i.e. DRL, clearance lights etc) with each power up? They replied with, you will always need to turn the unit on via the on/off button on the control head or thru app once you have either key in ACC or ignition on. Is that true? Does each button have memory of previous use at power off? However, I also wanted to be able to have the unit automatically turn on with ACC or ignition and have the preset lights come on. Trying to eliminate always having to turn the unit on after keying up the vehicle to turn on my DRL and clearance lights each time I start the vehicle. Thanks!

@robertionescu_

8 ай бұрын

I have exactly the same question about the memory function...

@davymill6696

8 ай бұрын

​@@robertionescu_ I did get this unit and although it powers up (the buttons light up) if using the accessory lead. Then you can either hit the "memory button" in the center of the unit to turn on any switches/buttons that were on when you previously cut power to the unit or, select which button(s) you wish to turn on individually. It will not power on any items connected to the buttons by default when turning the key on. hope this helps.

@robertionescu_

8 ай бұрын

@@davymill6696 Thank you. This helps a lot 👍

I would like to see the video from where you took the power with the ignition switch thanks

@Donslife

Жыл бұрын

Since most of the viewers don’t have the same vehicle, I left it open ended for the ignition trigger. But I did make a video following up: kzread.info/dash/bejne/k4prx9tuZJSblKw.html

Any chance you could make a reel or shorts about which accessory you have in which slot?

@Donslife

10 ай бұрын

My Community page here on KZread and my Instagram both have a picture with labels that can help you out

Nice video 👍 If my light bar needs 35 amps (420W on 12V) and the switch panel only has up to 30 amps, how would i wire the original harness with a 40 amp relay into the auxbeam switch panel? Would that work? Thanks.

@Donslife

7 ай бұрын

You would hook it up with 40amp harness/relay as per the lightbar manufacturer’s instructions and just use the Auxbeam as a switch. You could use a 5A circuit just for switching the 40amp relay on and off

@offroad_adventures2934

7 ай бұрын

@@Donslife Thank you loads. This is a big relief. 🙏

If you leave the light bar on in the switch panel and you turn off you engine and you turn on the engine back on the lights are on or you have to press the on button in the switch panel to turn them on again

@Donslife

Жыл бұрын

If main power is cut from the panel, everything is off and has to be repressed. You can wire it up differently of course. After this video I added a wireless remote that can turn it on regardless if the truck is on or off too

Hey don, what do you plan on doing with the extra auxbeam 6 gang panel. I would like to put it on my at4 as well but times are getting tough with inflation and fuel. You should do a giveaway. Reward your viewers !!! Or you can send it to me lol. Just a thought. Hope you enjoyed Sedona. Thanks for everything you do.

@Donslife

2 жыл бұрын

Good Idea for the giveaway. It has already gone to a good home. Thank you for watching and all of the support

I am leaning towards Auxbeam > more expensive options but I don't like that I have to turn my IGN on to power up my accessories. Is the app control also dependent on IGN being on?

@Donslife

2 жыл бұрын

Fair point. You can wire up the switch panel to constant too. Really up to you…….or you can add a diode and a remote switch like I did in the video. Now I can sit by the campfire and turn the switch on remotely, while controlling all the gadgets. (For example) 😊 Adding a Wireless Remote For My Accessories! kzread.info/dash/bejne/k4prx9tuZJSblKw.html

Finally something cheaper than the switchPro

Might be a dumb question, but would this work for dual color, strobing LED emergency response lights? Seems easy enough to install, just don't want to waste time if it won't work.. Thanks!

@TheSleepyScout

7 ай бұрын

The question I'm currently having 😢

Hi, thanks for the tutorial. What's the name of that light bar that you show on your truck?

@Donslife

Жыл бұрын

No Problem. I had a 20” Rough Country with DRL but now I have upgraded it to a Strands Siberia 22” lightbar. I have videos for both

@alefpvc.r.4540

Жыл бұрын

@@Donslife great, thanks 👍

Great video, and detailed installation vide. Let me comment that AuxBeam switch panel are crappy products, and customer service is terrible I install AuxBeam switch panel AR-800 according to included brochure, and only lasted 3 days, and I had to fight hard with customer service department to get my refund, I do not recomend this product at all!!!!!

@Donslife

Жыл бұрын

Sorry about your experience. Mine has been consistent and reliable. I have 7/8 switches being used currently.

Whats your thoughts on garmin powerswitch?

How is that motherboard? Much taller than regular 8 gang? Thanks

I just got to the part of the video where you said you have a compressor under your hood? I know I didn’t hear that wrong because I even ruined it in. Heard it again, lol. Do you have a video showing the install of your compressor?

@Donslife

Жыл бұрын

There are a couple related to it. Here is the main one : How to Install a Wireless Compressor for your Air Suspension kzread.info/dash/bejne/ooB3q8uaptSxpKg.html

@Donslife

Жыл бұрын

And another: How to Install an Air Line in Your Truck! kzread.info/dash/bejne/hJyl1attfqaYorg.html

I was looking to use this panel to run white/Amber pod lights. Would I be able to have 2 switches control each color of the light (set one to run solid white, the other strobe Amber). Would I have the jump the ground between the two switches? Thank you.

@Donslife

2 жыл бұрын

I have a newer light bar with amber and white DRL’s. They are hooked up to 3 switches. One for each color and the lightbar array itself. Works wonderfully. You should be able to run each positive wire to each individual switch too.

Ah Don. I was waiting for you to visually show me mounting options inside the cab. Anyhow, I just bought one using the code. Originally $300, Auxbeam is currently already 10% off at $269. With your code it gets down to $243.

@Donslife

2 жыл бұрын

I only found the one spot that wouldn’t involve screws or cutting

If I have lights that I would like functioning while the ignition is off, does this switch Bank drain the battery if the accessory wire is hooked up to a power source that isn't ignition dependent?

@Donslife

11 ай бұрын

It will drain a little power to illuminate the LED backlights for the panel if the remote wire is connected to an ‘always hot’ source. I left my panel powered up overnight and my vehicle wasn’t really drained. Over a few days it could be a problem. You might want to do something like this : kzread.info/dash/bejne/k4prx9tuZJSblKw.html

Can you turn the pod light on without the ignition on or no? And if yes, how do you wire where the pod light can turn on without the ignition being on and would it drain battery? Thank you

@Donslife

Жыл бұрын

Yes there is a way. Here is one way that I did it : Adding a Wireless Remote For My Accessories! kzread.info/dash/bejne/k4prx9tuZJSblKw.html

Can you dim the light bars and stuff with the app also like the trigger controller?

@Donslife

Жыл бұрын

No you can’t with this switch.

Those with a 2022 or so GMC AT4 where did you connect the fuse tap wire to an ignition source?

@Donslife

Жыл бұрын

Passenger side fuse box has more options. The cooled seats is the one I used. Not sure the location on the 22’s

Do it have any trigger inpputs? Like hight beam signal = turn on switch 1 and 2 ect. I think I liike the Switch Pros better.

@Donslife

Жыл бұрын

I get it but this is 1/3 the price is all

How did you end up mounting the panel? Adhesive or screws/cutout? Was unclear

@Donslife

2 жыл бұрын

3M adhesive strips on the flat area of my dash.

to group lights do you have to have your phone hooked up all the time or will the control panel remember the group?

@Donslife

25 күн бұрын

No need to use the app each time.

great video, have a question.. I install the one thats not compatible with the app. if i get the one with the APP do i have to chasnge just the control pannel?

@Donslife

Жыл бұрын

Good question, as far as I know the control panel that goes in the vehicle is what ‘talks’ to the app. So as long as the switch box is compatible with a Bluetooth capable panel at a later time, I think it would work. I would ask Auxbeam to be sure just in case the physical connections vary. To be fair, I only installed the one panel and haven’t had experience with their other switches/panels

@saulbahena4061

Жыл бұрын

It worked with just the controller. Thanks for responding tho

I need some help!! I try installing this today after watching many KZread videos about the RGB 8 switch panel, man no matter what i did every time I have this connected to my battery my car wont start, if like the battery die or something. I thought I have the wires installed wrong, changed the wires and same problem. I did however got the panel to light up the first try but when I press the starter on my truck it wouldn't start. Anybody have an idea what's going on? also none of this videos tell you that if you install the add a fuse inside the cabin your fuse cover wont fit anymore, even with mini add a fuse wire. Please help!!!! I have a tacoma off road 2020

Is there an option to have the system turn an input on (light bar) when you start the truck instead of having to manually turn it on via the all or in-cab control?

@Donslife

9 ай бұрын

Not on this model that I am aware of. If you wanted to do that, just hook up a relay as a trigger wire to your high beams

@user-mz7cx1oz1h

9 ай бұрын

@@Donslife thanks, man!

Just curious 🤔 if you can have constant power to the panel since you can shut off the lights anyway? More or less if you're at a car show, that you're not having your acc,on

@Donslife

Жыл бұрын

Yes you can. You’ll just drain your battery a little more quickly depending on what you have running as well as the backlight for the switch

@Donslife

Жыл бұрын

I added a remote switch : Adding a Wireless Remote For My Accessories! kzread.info/dash/bejne/k4prx9tuZJSblKw.html

Hi I have RC pod lights that have drl and spot light how did you wire that up?

@Donslife

2 жыл бұрын

Both pods DRL positive lead connected to a lower amount circuit (probably a 10A) Both pods MAIN LAMP positive leads to the 20A or 30A. One ground to the body or the ground terminal in the switch box. I would check the specs for each pod and determine the Amp draw of each so you know what their combined draw is on each switch circuit. Then pick the appropriate one.

Can you dimmable LED strips with this? I want to install LEDs inside my camper and be able to dimmable them also. Is this possible with this switch?

@Donslife

Жыл бұрын

Hi there, the switch won’t control a dimming function. The light strip itself would need to have a dimming feature that you’d have to adjust with it’s own app or mechanical knob/slider.

You may have answered this, but I have a 3 way switch for light. On/off/backlit. Will this panel allow for all 3 positions?

@Donslife

16 күн бұрын

Not that I am aware of. A 3rd position would need a 2nd switch to be used.

i like it but what happens if the relays fail? on the gang you can atleast replace

@Donslife

Жыл бұрын

I live life on the edge 👍🏼

hope you see this but how did you mount the pod on the dash?

@Donslife

Жыл бұрын

Double sided tape (good quality) used on emblems

You mention being able to use " Android box" to connect it to the infotainment. Do you know what system you use for this, I dont see it listed in your products? I have been less than satisfied with a few that I have tried to connect my Sierra. Thanks

@Donslife

2 жыл бұрын

This video here : MAJOR UPGRADE for Your Existing Wired Car Play or Android Auto! KZread and Netflix! kzread.info/dash/bejne/jI2Do66Ho7HgoKw.html

@ffemt703

2 жыл бұрын

@@Donslife gotcha....not even close to worth $400 asking price...thanks for info though

🔥🔥🔥

@Donslife

2 жыл бұрын

I will be adding some more things to hook up to these switches soon enough!

@Auxbeam

2 жыл бұрын

@@Donslife Great! That would make driving more easier!

You have a compressor on your truck? Any video of the install?

@Donslife

9 ай бұрын

Here’s one: How to Install a Wireless Compressor for your Air Suspension kzread.info/dash/bejne/ooB3q8uaptSxpKg.html Later on I add an auxiliary air line too

Hi sorry to bother you, I have a 2022 gmc sierra at4 and purchased the smoked mirror lights with signal lights. Came with no instructions and wondering where would be the best place to run the signal wire to. It's the light on the mirror face

@Donslife

3 ай бұрын

I’m consider finding the fuse for each signal light and connect there with a fuse tap

@travisjesso9415

3 ай бұрын

@Donslife I was hopping to tap in the harness in the door if there was a wire for the signal, not sure if there is or not. If not I would have to do it the way you said. Thanks so much for getting back so fast and for your time

Great video. I have a question. Can it be operated via Bluetooth with the ignition off? I camp in the middle of nowhere and if something is stirring around camp I would like to be able to "Light up the night". Thanks

@Donslife

8 ай бұрын

Yes if you wire the panel to be live with the ignition off

@Overland_eXploits_Oklahoma

8 ай бұрын

@@Donslife do you know if it has any amperage draw that way? With all accessories off, of course. Thanks for the quick reply.

@Donslife

8 ай бұрын

You can add a remote turn on like I did

@Donslife

8 ай бұрын

Adding a Wireless Remote For My Accessories! kzread.info/dash/bejne/k4prx9tuZJSblKw.html

@Donslife

8 ай бұрын

This way I can turn the panel on from 20ft away and connect my bluetooth to operate anything

If you forget to turn the lights off does this automatically turn them off after shutting the truck off?

@Donslife

Жыл бұрын

Yes, when the truck is turned off the panel will lose power too and shut off all accessories connected to it. I chose to wire it up this way. In a later video, I added a remote to be able to turn the panel on and off independently of the truck. Adding a Wireless Remote For My Accessories! kzread.info/dash/bejne/k4prx9tuZJSblKw.html

Do both units do the strobing or just the one with the Bluetooth ?

@Donslife

8 ай бұрын

Some non-Bluetooth models have the feature. Look for ‘pulse’ as an available function

Hey Don With the ignition cable… where would you put that for somebody who doesn’t have a compressor? Lol

@Donslife

Жыл бұрын

Cooled seat fuse tap on the passenger side of my Sierra. Any ignition switched fuse will work. The current draw is minimal

@mike1024y

Жыл бұрын

@@Donslife thank you man 🤙🏼

I noticed you didn’t touch the brightness in the middle. Is the brightness for the panel or for the lights you’re turning on/off on the light bar?

@Donslife

6 ай бұрын

Brightness is for the panel, which also has an ambient light sensor to adjust itself

@jeromefronda252

6 ай бұрын

⁠gotcha, but to confirm no way to dim the actual lights outside of the vehicle? I have Baja S2s on my roof rack, but at night camping it would be nice to dim them from being too bright

@Donslife

6 ай бұрын

@@jeromefronda252 unfortunately this panel only does switching, no dimming. Be careful too, not all lighting will allow dimming.

Which fuse was your pink wire going to? I am not sure which fuse to connect to on my 22 sierra.

@Donslife

Жыл бұрын

I ran it to the ventilated seat fuse on the passenger side panel inside the cab

@MikelM06

Жыл бұрын

@@Donslife This is the biggest question I have as well. I looked and a few others, and they also have this question, but I, unfortunately, don't understand your responses. I do think I understand that it's your pink wire in this video. I went to the compressor video but could not find exactly what you did here. Is there another wire or anything anywhere closer or easier to find? or do you have a video clip of this? Thanks so much for all the videos. Just used a ton of your discount codes so thank you!