Your lathe build is impressive, well done, I watched all your videos. Did you use a special steel for the main spindle?

amazing project

@mr.ranyhomemade2466

8 ай бұрын

Thank you

looks cool!

@mr.ranyhomemade2466

8 ай бұрын

Thanks my friend all the best to you too

Very very good

@mr.ranyhomemade2466

5 ай бұрын

Tha

Top job my friend, its amazing what you can do if you put your mind to it.

@mr.ranyhomemade2466

8 ай бұрын

Thanks for your patience and introduction me, I made it but I’m not sure how to call because is not my job and learn without book or have training before everything I did apart of my Diy. I am appreciate your info Thanks

Olá amigo muito criativo ta uma maravilha o projeto, parabéns!!! Lhe desejo sempre muita saúde e cada vez mais sucesso!!! Abraço

@mr.ranyhomemade2466

8 ай бұрын

Thank you for your patience my friend, how are you doing? All the best

I'm waiting next episodes

@mr.ranyhomemade2466

8 ай бұрын

Thank you for reaching I do hope you enjoyed I will keep improving.

At 10:48, watch the bearing in the background spinning while your cutting on the shaft, Your tailstock is a serious problem, a large source of vibration. Probably the center your using, is it a live center or a dead center ?

@mr.ranyhomemade2466

8 ай бұрын

Thanks for your patience and introduction me, I made it but I’m not sure how to call because is not my job and learn without book or have training before everything I did apart of my Diy. I am appreciate your info Thanks

Top eu também tô construído um torno

@mr.ranyhomemade2466

8 ай бұрын

Let go my friend

how shaft diameter and bearing code？

@mr.ranyhomemade2466

Ай бұрын

I’m forgetting I will let you know tomorrow

The problem I see with the pully setup is that its too small and rubber from the belt can get into the bearings. Screwing on faceplates has its own problems too as you are relying on the threads for accuracy and you will be praying that doesn't come undone or even move a little as it will throw your parts off its center making it impossible to hit tight tolerances. There are reasons why most laths have fixed face plates and the ones with removable face plates are a pain to deal with.

@mr.ranyhomemade2466

8 ай бұрын

Thanks Ham That is my concern very much because I do not have my own machine. The pulley is used size B think a bit small, the charge me 220$ for two pulley so expensive but choice Thanks let how is first im sure.

@mr.ranyhomemade2466

8 ай бұрын

Thank you for your patience in watching this, learn to make this machine without book and no school it one part of my day only, and I started during a pandemic and have been Covid 19. Thank you again

@hampopper3150

8 ай бұрын

​@@mr.ranyhomemade2466 No rush for me at least. I kind of like the slow progression anyway.

@1crazypj

8 ай бұрын

Screw on chucks were very common until 30~40 years ago and plenty of people still use them as hobbyists with older machines The only thing I would do different, the shoulder behind the screw on part should be cleaned up accurately to be concentric with thread/bearing then a counter bore in the nut to keep things in line. Screw on chucks can have problems if you do a lot of intermittent cutting as they tend to get too tight to remove (at least without a struggle) and, if you have the ability to switch from normal running to reverse without stopping first, they can come unscrewed. It will be simple to make a thin plate to keep any rubber out of bearings, getting grease from bearing onto belt may be more of a problem although the same thin plate will act as a slinger to keep grease or 'dirt' where it belongs. The only problem I foresee is changing belts as the spindle will have to be disassembled, although the PK Truck video's don't seem to be bothered by the same design. which came out of a factory that way

Ustam o punta nasıl bir punta anlamadım.

@mr.ranyhomemade2466

8 ай бұрын

Thank you what did you say my friend