fantastic result!!👍👍sounds peaceful wherever you are..

@mr.ranyhomemade2466

Жыл бұрын

Thanks for your best time I will try my hard work to be best. I am Cambodia one of the small country southeast asian.

You did the great job, brother. Lovely video.

@mr.ranyhomemade2466

Жыл бұрын

Thank you for reaching I do hope you enjoyed my work.

That was actually a neat way to fabricate a 'T' slot. I was thinking you may need to modify bolt heads so they can't spin in the future when things wear in. 220mm is a big diameter for a small lathe, I couldn't do it as my lathe doesn't slow down enough. (500rpm is slowest it goes) I have used an angle grinder bolted in place of tool post to grind larger diameters around 185mm

@mr.ranyhomemade2466

Жыл бұрын

Thanks for your introduction it very hard for me everything I made is from my mind no one tells me you make this or that. this machine is my dream. I will change some part is possible.

@1crazypj

Жыл бұрын

@@mr.ranyhomemade2466 To be honest, a heavier lathe is always better as it won't vibrate so much and is more stable. If possible, fill hollow area's with hydraulic cement/concrete (not 'ordinary' Portland cement) as it doesn't shrink and is much much cheaper than epoxy. I trained on much bigger lathes and actually owned a very nice Colchester for a few years but had to sell it when I moved

You're an inspiration. I hope I can replicate your work, thank you for sharing!

Belo trabalho na construçao de maquina caseira. muito o brigado

So amazing your creative

@mr.ranyhomemade2466

Жыл бұрын

I appreciate for your best time to watch my hard work.

Trabalho De Mestre My Friend directo Do Brasil Paraíba 🇧🇷🇧🇷

@mr.ranyhomemade2466

Жыл бұрын

Thank you

Thanks for sharing.

@mr.ranyhomemade2466

Жыл бұрын

Thank you for your patience 🙏🙏🙏

عمل رائع جدا شكرا جزيلا

@mr.ranyhomemade2466

Жыл бұрын

Thanks for your comment

The master 👍

@mr.ranyhomemade2466

Жыл бұрын

Thank you for reaching I do hope enjoy

Olá meu amigo, muito bem elaborado, essa ideia ficou fantástica da até vontade de mudar o meu!!!Esse modelo ficou muito pratico, parabéns pela qualidade de trabalho e projeto sempre!!!! Abraço e boa sorte com muita saúde e cada vez mais sucesso!!!

@mr.ranyhomemade2466

Жыл бұрын

Olá meu amigo, como vai você? como é o seu trabalho ? bem, vou tentar o meu melhor, sabia que é um trabalho árduo, o problema não é nenhum equipamento, como fazer, posso dizer 60% feito à mão, então tudo parece lento, como um acessório de fresagem, apenas 4 peças, fiz 4 dias. obrigado novamente

Nice Work!

Very nice.

Nice

@mr.ranyhomemade2466

Жыл бұрын

Thanks for your watching

what's with the coke spoon on your pinky finger?

I love your work but I hate rusty tools and machines. There's no pleasure watching neglected machines. Please clean up and lube your hard work. They deserve it! Wakodahatchee Chris

@mr.ranyhomemade2466

Жыл бұрын

Thanks I appreciated your suggestion I will try my best you knew better than me please let me know Thanks 🙏

How much motor bos

@mr.ranyhomemade2466

Жыл бұрын

Sorry what did you mean

@embitnawai3190

Жыл бұрын

@@mr.ranyhomemade2466 boss, how many watts do you use???

@mr.ranyhomemade2466

Жыл бұрын

Sorry I don’t understand what you’re mean 🙂

@embitnawai3190

Жыл бұрын

@@mr.ranyhomemade2466 how many watts does the boss use

@mr.ranyhomemade2466

Жыл бұрын

Thanks For milling attachment I used 3 pieces

😃😃😃😃😃😃😃😃😃😃😃😃

@mr.ranyhomemade2466

Жыл бұрын

Thank you for reaching I do hope enjoy my homemade

Nice

@mr.ranyhomemade2466

Жыл бұрын

Thank you for reaching