MYSTERY SOLVED! Honda CRF250R Dirt Bike Won't Start FIXED
I work on a 2010 Honda CRF 250R dirt bike that won't start. Let's figure out what's wrong with it. #Honda, #Mystery, #250,
►SUBSCRIBE: / @2vintage
►MY SECOND CHANNEL: • New Polaris ATV Snow P...
► ADD ME ON ALL SOCIAL MEDIA ◄
► FACEBOOK: / 2vintageyoutube
► INSTAGRAM: 2_vintage_ / 2_vintage_
► SNAPCHAT the2vintage
► EMAIL FOR BUSINESS INQUIRIES ONLY: 2vintagetooo@gmail.com
Thanks for watching and subscribing!
New videos every week!
The following video features activities performed in controlled environments by knowledgeable persons. DO NOT attempt to duplicate, re-create, or perform the same or similar activities at home, as personal injury or property damage may result. 2vintage( Joe Weber, the persons shown in this video and ANY CONTRIBUTOR, ARE NOT LIABLE FOR ANY such injury or damage. ALL 2vintage( Joe Weber) CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.
2vintage (Joe Weber) makes no representation about the sufficiency of any safety precautions and equipment used in this video.
Пікірлер: 385
Don’t have the ability to ride motorcycles but I enjoy your content
Tighten the Kickstarter. I can see the washer spinning around. Thanks for another awesome video!!! Keep it up Joe!
Dont use the gashandle when starting a 4-stroke, you will flood if instantly. Put cold chock and start it without any gas handle, then release choke when idle rpm drops.
@theboogieman401
2 жыл бұрын
Thankyou
@pistolz3004
2 жыл бұрын
Hey stupid its not a gas handle its called a throttle and when starting a 4 stroke… fuel injected or not you always hold the throttle open a little and the choke is for when its too cold out side to start a bike… PLUS FUEL INJECTED BIKES DON’T HAVE CHOKES BECAUSE THEY DON’T HAVE CARBURETORS
@COMPY357
2 жыл бұрын
Gashandle- throttle???
@COMPY357
2 жыл бұрын
Gashandle- throttle???
@COMPY357
2 жыл бұрын
Gashandle- throttle???
Difficult to start, understatement. They're all a chore more often than not. Your doing great in this stuff, will make a great lead mechanic somewhere!!!
Little tip for razer blade work, a piece of masking tape on the back of the blade makes a very comfortable little handle. This gives you a lot more control on the blade.
@darkfire8615
Жыл бұрын
Thanks for the tip 👍
@BeersAndBeatsPDX
Жыл бұрын
That's a damn good tip
@ThisIsGoogle
Жыл бұрын
Thanks, local drug dealer.
You've came a long way and learned a lot. I've been watching ever since the all the cr85 pranks on Charlie. I've also learned a lot through your vids too.
@krazyk09
2 жыл бұрын
Yes I rember all of that I would not be where I am without this dude
Saw where another person uses a thick piece of glass and some ultra fine grit sandpaper to surface the cylinder machined areas. That way you know the surfaces are flat . He has found quite a few that were warped this way.
nailed it joe , you did find all the faults. i noticed most bike with new piston and rings are tough first start. the woodruf key ever did see a stepped one, to change timing? allow me a small joke. looks like your right leg has more muscles.....
you can use your bike stand for a step when loading/unloading bikes out of your truck thanks for the videos 📹
Cool video. I have a 2017 crf that is experiencing similar symptoms. Pops when you kick it and won't start. I guess I'll check my woodruff key. I wonder how the one on this bike got so bad?
Cool video. Also noticed that the kickstarter bolt was loose, you could see the washer shaking when you gave it gas.
@2vintage
2 жыл бұрын
Yep tightened that up
I like that bike, a little intimidated by fuel injection but if I got to take one apart I would probably understand it better. I looked it up and everyone like you said, found it hard to start
Pretty much any 4 strokes I always try to rotate right at the BTDC Timing mark/TDC-ish before kicking/pulling (then hit comp release) and surprise a lot of friends starting their motos/quads etc they say is hard to start. They are/can be a bit more of a pain to crank over compared to the 2 smokers for sure though lol.
@wadeseiler9307
Жыл бұрын
All about the righ technique , idk If this bike I carbed but mine likes to be primed three full twist then kicks in 1-2 kicks
Good job on the videos. Just want to note in my experience owning an 07 crf250r, it doesn't want to start with throttle open at all.
@fraserm803
6 ай бұрын
just bought an 07 250r (twin ex/carb) in uk. starting seems hit and miss tbh. im tryin to love it and learn its quirks.
Way To Go, Joe! Seems it was your biggest project yet.
I like to use permatex gasket remover, it’s a foam spray. Let it sit for 20 min and the old gasket comes off easy with plastic razor blade
Could you use 3 bond on that base gasket area? Needs a good pipe would you say?
Hope the bottom of jug has a good smooth bevel on it to put piston in. And there's not much play!!! Awesome. Great vid!
The reason you were seeing the really tight tolerances you're putting the piston in upside down in the cylinder the skirts of the piston are the widest part of the piston the top of the bore your skirt is never going to ride that high in the bore so you're not going to get that tight tolerance of the skirt in the top of the bar as the bore wears it wears tapered that's why the piston skirt is wider and for the way they expand thermally
You should find a cheap DRZ400 & rebuild that. Super popular enduros! Keep up the great work. Learning a lot.
@thomasdausch8557
2 жыл бұрын
Yes i agree , i had a 2007 DRZ-400S, it was a great all around bike , i live in florida and bike was too heavy for the sugar sand down here,,if my health was better i would buy another one, high seat and a struggle to get leg over saddle
It makes it way easier to start a fuel injected 4 stroke if you don't twist the throttle upon kicking/starting.
Watch the difference it adds to the start ups.& performance after doing so to.
Woodruff worn/cut on an old school buke meant the timing was off. 50 years ago I bought an almost new 650 triumph Bonneville cheap cause it wouldnt start. The problem was a sheared woodruff key. What a deal, rode it for many years.
Is the popping on decel like at 27:03 and 27:34 normal for these bikes? I have an 08 CRF250R that does that and I can't get rid of it no matter what I do.
I have a question my 2017 Honda crf250r is hard to start I spray brake cleaner in the throttle body and the bike starts after the bike is warm it’ll start right up does that mean my compression is good?
Nice dude! Runs like a champ! Nothin like a CRF250 to rip around on
Hey I have a 2005 trx400ex I know nothing about bikes and it don’t start I don’t know what’s wrong with it I wanted to know how much you charge you can fix it?
Dude, I had a yz426 that was terrible to start. It had a choke, primer, and a decomposition lever. The starting ritual was mind numbing, but once it was going it was a riot
@haigpogharian2145
2 жыл бұрын
Recently sold my 426. Once I got the method down, it would start first kick everytime. Thing was a powerhouse
@bananabrooks3836
2 жыл бұрын
Only certified taxidermists can fit a decomposition lever.
@jeremyclose705
2 жыл бұрын
@@bananabrooks3836 hahahaha I'm not even going to fix it. That's just to funny
@nathanchappell3842
2 жыл бұрын
Top dead centre decomp lever in.tiny bit past with decomp lever let the lever go all the way to top of the stroke of kick-starter should start first kick cold or hot
I love your channel. KEEP IT UP!!!
Man you never let anything get in your way! Great job once again!
@alexdelapazz
Жыл бұрын
I got one of these and the kickstarter is stuck, and there appears to be no oil in it. Could the engine be toast?
They have primer rebuild kits for those. To fix the not priming issuers is having on it for first enishle kick start up from setting up.,or not started in A while. I'd really invest in putting just 3 ounces of stp oil treatment& bars stop leak in the motor oil to bend into the crankcase.& clutchcase to.
Hands down the best KZreadr out there
I would find out why the woodruff key sheared n where the chunks went...😃👍👍👍👍👍👍👍👍
I have one of these, starts absolutely fine and pulls much better than this does! You should be on the back wheel on that tarmac with the power?
Look on the previous video TIMING all the time the response as you tried to start it said timing instantly ( PS i used to hand build race and rally engines as a hobby )
That bike should be starting in one or two kicks, you turn on the choke plunger, push down the kicker a few times and then do one or two good kicks from TDC and it should start up, and when it is warm you should have one kick from TDC no choke
have you checked the compression after rebuild?
I have a crf250r, 2004, darn thing only wants to fire right up if I start at TDC and just give one hard kick. Otherwise I kick it all day. Overjoyed when I figured out that trick with my own. Second whenever I do a top end I take the spark plug out and kick it over like 20-30 times to get the oil back up top before I start. You definitely kicked it over 20-30 times before it started 😂
Ik I’m abit late the I know your use to the craby bikes blipping the throttle when kicking the bike. With efi when you twist the throttle it cuts off power to the injector. I own this exact model no speed gear 3 light kicks and then 2 hard kicks start every time. I was having a problem with the idle it was really hard to start but once that was figured it out she was running beautifully
You did not show how to install chain tensioner. When I did mine , it rotated the cam off timing...still do not understand what I did wrong....
These 250Rs are good bikes but can be a pain to start. I had a '04 250x that had beat to hell valves and after shimming, carb clean + JD jetting and accelerator pump mod/tuning it ran good after 3-4 kicks cold. Unfortunately with the nature of those valves in early years it needed a new head and valve job so I sold the bike while it ran, not worth it. Newer years aren't so bad I hear but still hard to start. To me these bikes are a great example of how complicated modern 4 strokes with insanely high maintenance. That's why I went back to 2 strokes.
@bike23august
5 ай бұрын
I have a 04 crf250.. I can cold start it in flip flops. I adjusted the carb and since it runs great. If the carb is not perfect it will be harder to start but if it's how it should be it's very good. The valves if you just go with stainless steel then it's very reliable, that's my next step on it to change them while it's still good. Still can't beat a 2 stroke 😂😂
Do you give you fuel injected truck throttle when you start it?
Hi Joe grait vid .. not sure if I noticed the kick start washer loose 🤔
Mr Joseph, Muse you do have a bad habit of giving it gas before and while kicking it. I have an 09 RMZ 250 and you know what a pain they can be to start. I start mine cold usually the first kick, sometimes it takes two. Make it happen Captain. Great content Joe
Bro never disappoints when I get a notification on a banger video
Good vid, but don’t use the throttle on a fuel injected bike the ECU will do its thing and give it enough fuel hence “electronic fuel injection” only on older carby bikes you will need a little accelerator to get it goin, otherwise great vid boss!
Great job joe bike runs nice brilliant content mate all the best 🔧🔧🔧👍👌
Should i ride my dirt bike with stock tires on the road (they are ofroad tires) its a new bike but yeah....
I had an older xr200r what would only start if you gave it full throttle
Fuel injection, don't crank the hell out of it. Not sure how they work without voltage but runs good, only gets minimal at kick so not a lot of power there, but once it fires it's golden. Great job on that beast!!
You should try using a service manual from honda it will show you exactly how it should be done not how someone what's to do it. This is the reason the shops get you for alot of money to fix it right the first time.
Good job sorting this bike out.
here's a tip for removing gasket get yourself a wire wheel for a drill lightly running over it takes it off real quick
That woodruff key is only an issue if that nut isn't tight. It shouldn't move when torqued down.
I have home dirtbike cylinders I have that coating in the cylinder and never had an issue with it can I use a stone on but you gotta be very careful I know several machine shops also they do the same thing I just gotta know what you’re doing I have rebuilt several bikes that way I’ve never had a issue
I think i know why it didnt wanted to start. I have a Rmz 250 and if i twist the throttle when I'm starting it it hardly ever starts. But if i let go the throttle it starts first kick. Just a tip, maybe try next time.
@dnickens20115
2 жыл бұрын
Yeah I saw that too every time he crank the bike he twist the throttle..
@2vintage
2 жыл бұрын
I tried many many times with no twisting of the throttle. No change.
I had a 2009 they had the same issue. By time you got the stupid things started you didn't feel like riding anymore.
I had for my son a Honda 2019 Crf150 r dirt bike, it was very hard to start too. I had such high compression it hurt you foot to kick it over. Really enjoy you videos ! Thanks Joe
Work your heat cycles with that so it's broke in right. Sounds great@
If you can’t ever get a carb clean cause it’s so gummed up use straight sea foam and works like a charm I had to use it on a late 80s sled and and nothing would get the gunk out except for straight sea foam
@sevendyseven4090
2 жыл бұрын
Na, just remove carb, clean it out properly instead of band aids..
@jukeboxentertainment1740
2 жыл бұрын
@@sevendyseven4090 what I did but carb cleaner wouldn’t work so I tried seafoam and worked
it feels so weird to see Joe on a modern bike😂😂
Whats the break in procedure for the new top end on that bike. Multiple heat. Cycles?
@bradenrides7386
2 жыл бұрын
yea low and high rpm's on and off for a whole tank of gas
should always reseat the flywheel too.. probably isnt seating well to shear that woodruff key off
👋👋👋Wiseco is good parts ?or what do you recommend
Do you sell these on and if so how to go about getting one enjoy your vids mate
my old crf450r had to have the piston top dead to start and dont touch the throttle,they are all hard as hell to start.you can see me take a terrible hit racing mine on my channel...lol...the accident laid me up for a whole summer with a broken femur and bad hip,it was the start and finnish or my race carreer.sad part was i was catching the 3rd place rider on my second lap when it happened
Don’t give a fuel injected bike throttle while starting. Found that out the hard way
@kylekoenig7781
2 жыл бұрын
I've been told that this can cause major issues over time like throwing a rod through cases😂 what happened to you?
You can hone a nikasil cylinder with a hone that’s 320 grit or above
To set the idle on it don't adjust the idle by the cable and you got to remember it's fuel injection so to set the idle most people do it by the air screw yes there is still an air screw on a throttle body there is an actual Idol screw on the throttle cable side of the throttle body the air screw should be adjusted one and a half to two turns at the most from seated one thing to get it starting easier clean the screen in the fuel hat of the injector if it doesn't have a screen do not blow air through the injector you will destroy it send it to a fuel injector clinic
shouldnt u press kick starter from the top?
You don't have to hammer throttle while kicking, pump couple times and kick away.. nice bike.
A little tip for you if you want to here all the little ticks in the motor cut a old broom handle off about 3 ft long put one end on motor while it’s running the other end up to your ear you will be amazed it’s a old timers trick works good try it
I have the same problems of the client bike before 2 years. I, like you get everything off , do the clearance , new chain, look the piston and cilynder new head gasket replacement but the problem wasnt there and still!!!! The problem of that bikes CRF250R when they are hard to start cold is CARBUREUTR !!! I try to heat the carb with a heat blower and voalaaaaa its starts and runs from first hit of the kickstart ! Try it and you will see that works and bike will start after 1 2 kicks. In it have many o rings ,gaskets and vacuum membrane ( bad.... FCR carb....) wichn need to be changed ,in my country Bulgaria in Europe they are about 150$ US and my client said thats crazy and sold the bike and he show at the new owner how to heat the carb and easy to start it 😂 Dont know how to send you a video from my expiriance ,to see how easy it starts ...
All it needed was the boot 😂 fired right up
I love the way this bike sounds!
Your turning the throttle just kick it and there’s an air/fuel knob on the crab if you twist it clockwise it will lower the idle if you twist it counterclockwise it will raise the idle find the in between and it will idle perfect
People dont like to use gasket maker on a base gasket because it changes the squish. Witch for a performance high tolerance engine hurts performance and can damage the engine.
force of habit i get it but for future endeavors the fuel injected bikes dont care much for throttle when kicking
Master you.. have crf honda 250. 2017 very hard to start
Check out the carbide scrappers
I'm starting to think that you're not a certified mechanical expert. Any good mechanic especially a bike mechanic knows it's better for a whole motor rebuild if . The only people nowadays who only replace the Top end is season Motorcross racers and they only do it once Otherwise Can place Too much pressure on the lower end and wreck the Conrod kit or maybe even main lower bearings taking out the crank Seal anyway so from now on I would highly recommend to replace everything else in The engine if the bike isn't so New
@AUSTIN_457
2 жыл бұрын
I agree for the most part but are ya going to pay for his top to bottom builds ? Lol. I can't believe he can even afford this stuff even with all the corners he cuts. (Not this bike specifically just in general)
I need some help with my four wheeler. I have a 2005 Honda trx 450r. Was driving it when all of a sudden in 4th gear going fast it started to lose power when I gave it throttle. It starts and idles fine and can be driven but when you hit the higher rpm’s and gears it bogs. Any ideas?
@anthonylevin9584
Жыл бұрын
It's your carb. Check fuel lines my bike has the same issue it was a dirty petcock. Your jets also may be too small. Try throwing in a larger main
@YeoldeOrange
Жыл бұрын
@@anthonylevin9584 yeah I’ll have to check my carb out. Thanks.
@anthonylevin9584
Жыл бұрын
@@YeoldeOrange no problem
Dont they make ball hones for nikasil?
Hey 2 vintage you should start a bike repair shop
Where drained oil goes?
Love the videos. A bit of friendly advice. A mate of mine had a similar set up (albeit working on cars) with the oil soaked mat on the floor. He got sepsis from kneeling on said mat via a small cut on his knee & has had recurring health problems ever since.
@2vintage
2 жыл бұрын
Good to know! I'm getting rid of it right now then!
Sometimes u need to check the petcock under gas tank it gets clogged every now an then
Use hi octane gasoline in hard-to-start engines. It will improve starting.
where is power😅 my 04 husqvarna te450 take wheelie all gears😅 nice video!
Lol my 2015 pit-bike what hasn’t been run in 6 years started first kick 😂 and that’s a 4stroke also don’t gas it when kicking you’ll flood it very quickly
I didn’t know about the scotchbrite thing
Sounds abit rough still 😬
that didnt look like 10w40 that came out the engine, looked really thin like mobil 1 stuff. sounded like the clutch was slipping and that maybe the reason
@MirchiBoy
2 жыл бұрын
I'm guessing, engine was flooding so gas gets past the rings and thins out the oil.
kick slow and steady and follow thru
I think the majority of the problem is that your twisting the throttle when your trying to start it. Only do this on carbed 2 strokes! Not bikes with efi! Instead hold the bar pad so you don’t instinctively twist the throttle
brand new top end, and you didnt even clean the air filter before the first start up haha
Looks like the bolt for the kick start is loose , I can see the washer move when you rev it up
@T3AMR3ACH
2 жыл бұрын
I couldn't stop looking at it 🤣
Nice vid and nice dirt bikes
Is this bike out of Iowa or Iowa area?
Hell yah great video I'm a two stroke guy, you should get a cr 500 or kx500 those 500cc are getting very popular again from the 90s good job fixing bike can't Waite for new video to come out
@sevendyseven4090
2 жыл бұрын
Thanks in part to one Mr.Ken Kaplan