Incredibly informative thank you

Thanks for the informative video man. This is almost exactly what I want to run and this helped a lot. Thanks man!

@MotorMonks919

2 жыл бұрын

A year later and I finally have my build together. KA24DET with a 2871r. I referenced your video a lot when looking for hose routing and all that. Thanks again for making this.

@rustydomino694

2 жыл бұрын

@@MotorMonks919 finishing up mine too almost after a year :)

@rustydomino694

2 жыл бұрын

@@MotorMonks919 keep in touch let me know how it runs!

@MotorMonks919

2 жыл бұрын

@@rustydomino694 it’s running pretty great! Slight misfire at idle, but I’m not too worried about it right now. It’s heat soaking a little bit after LONG drives, but I plan on a bigger intercooler and some heat management wrap/tape/ etc.

@rustydomino694

2 жыл бұрын

@@MotorMonks919 Nice! Did you rebuild the engine too? I'm having a lot of trouble trying to install my transmission lol, no luck in getting the splines to align even when I know all the parts fit

I went blow thru maf because i could never get it to idle right with open bov or with recirculated bov. Once i went blow thru, it now drives like its non turbo. My valve cover vent and pcv both go to a catch can and then dumped to the rear by the muffler. I dont want that nasty blow by oil/fuel vapor going back into my motor.

thanks for the vid i want more lol

#Duvallllll! just subscribed im local in jax also.

Bro! 👏🏼

Did you have to trim your fan shroud to fit a koyo?

What kind of BMC (Or brake booster) do you have? You have a lot of clearance between your turbo and the brake lines.

@RonniegalloGT

3 жыл бұрын

z32. clearance is from the manifold.

@Therealzenkouki

3 жыл бұрын

@@RonniegalloGT Awesome thanks homie!

What intercooler piping are you running?

@srmx518

3 жыл бұрын

Second this!

@RonniegalloGT

3 жыл бұрын

I think it’s crx racing. bought it second hand.

What size injectors are you running?

@RonniegalloGT

Жыл бұрын

720s but 550s would of been fine.

What rpm does it hit full boost at? I'm planning running the same turbo

@RonniegalloGT

Жыл бұрын

3500

@christosfloros2359

Жыл бұрын

@@RonniegalloGT thanks!

Do you still run this set up or swapped it

@RonniegalloGT

2 жыл бұрын

Still run it

@Ebk1988

2 жыл бұрын

@@RonniegalloGT total cost of build ?

@RonniegalloGT

2 жыл бұрын

@@Ebk1988 hard to say. I built it myself and swapped parts. About 1g in machine work. 1g for internal longblock parts. 3g in turbo parts. 5g makes sense

Did you tune it yourself ?

@RonniegalloGT

2 жыл бұрын

No. RS Enthralpy

@guillermobocanegra350

2 жыл бұрын

@@RonniegalloGT I bought an ecu with es enthalpy tune only probably I don’t know what base tune it has tho 😅

@RonniegalloGT

2 жыл бұрын

@@guillermobocanegra350 you need to mail it to him and tell him your setup.