MTD Transmission Adjustment
Тәжірибелік нұсқаулар және стиль
In today's video, I work on a Yardworks 2-stage snow blower that has transmission problems. It goes super slow in full reverse and too fast in the forward gears. Let me show you how to adjust the transmission.
The content in this video might not be applicable to your exact piece of equipment. Any damage or loss to persons or property that may result from use of information contained in this video is the sole responsibility of the user and not Brant Small Engine Repair.
Brant Small Engine Repair encourages the use of safe practices and safety equipment while working on your machines and therefore assumes no responsibility for personal injuries. The information contained in this video shall be used for informational purposes and used at viewers discretion.
On my channel. you will find repairs to many different makes and models of lawnmowers, trimmers, generators, rototillers, snow blowers, chainsaws, lawn tractors, pressure washers. If you're looking for repairs on Honda, MTD, Ariens, Husqvarna, Murray, Weedeater, Toro, Troy-bilt, Echo, Stihl, Craftsman, Mastercraft, Bolens, Brute, Firman, Generac, John Deere, Poulan Pro, Homelite, Canadiana, Noma, Remington, Powermore, Tecumseh, Briggs and Stratton, Kohler, Yardworks, Yardman, Yard Machines, etc, this is the channel for you.
Music by: Nana Kwabena open.spotify.com/artist/6QDtF...
Пікірлер: 19
Excellent video with just the right amoumt of explanation during the adjustment. Thanks for sharing your knowledge with us.
@brantsmallenginerepairs
7 ай бұрын
Glad you enjoyed it! Thanks for watching and taking the time to leave a comment. Cheers
perfect. just getting mine ready for winter and noticed some reverse issues.
@brantsmallenginerepairs
7 ай бұрын
Glad I could help. Thanks for watching and taking the time to leave a comment. Cheers
Good video, thanks
@brantsmallenginerepairs
7 ай бұрын
Glad you liked it! Thanks for watching and taking the time to leave a comment. Cheers
When I make that type adjustment since the rubber is wearing in a new position I clean off the friction disc and lightly sand the surface to take out any wear from the old wheel placement.
@brantsmallenginerepairs
7 ай бұрын
Cleaning the drive disc is always recommended when you are already in the transmission area. Lubricating the drive shaft should also be done. I have not included these steps in this video as I have other videos where I show complete transmission servicing. Thanks for watching and taking the time to leave a comment. Cheers
Hi, I just watched your impeller video I like your content so I subbed to your chanel.
@brantsmallenginerepairs
6 ай бұрын
Awesome, thanks for the sub! Cheers
@Dave7160
6 ай бұрын
@@brantsmallenginerepairs your welcome
good info...thanks
@brantsmallenginerepairs
7 ай бұрын
Glad it was helpful! Thanks for watching and taking the time to leave a comment. Cheers
Use vice grips at 8.20 to hold the position you want then tighten the bolt ?.
@brantsmallenginerepairs
6 ай бұрын
Was able to get it done without but good tip. Thanks for watching and taking the time to leave a comment. Cheers
I can see those mtds very inviting the Little Critters considering that transmission boxes 2 big gaping holes on either side. How long does it really necessary.
@brantsmallenginerepairs
6 ай бұрын
They definitely like to take up camp there. Thanks for watching and taking the time to leave a comment. Cheers
Sorry just lot of talking
@brantsmallenginerepairs
7 ай бұрын
I am explaining how the system works to try and help others in the KZread community. Sorry it wasn't up to your standards. Thanks though for your input. Cheers