I got me a pull start to. My 3rd build but first pull start so I came to see how its to be installed. I saw rims like yours on Amazon I like them

@barriosbuilds7688

11 күн бұрын

@@adminkewl pull start is probably the worst part on the bike. I’ve been through 3. And then I just went back to the stock setup. They just keep breaking down. Also those rims are amazing! Still running them to this day.

I have installed a few of these on customers bikes. Don't bother to use them, they are junk, and will only break after a few pulls. I no longer use them on any of my customers bikes.

@HighMileageOffroad

3 жыл бұрын

Yup get a Grubee with an electric start capable crank!

@christianbelcourt279

2 жыл бұрын

I've had mine on for over a year, hundreds of rough pulls and no problems.

@ethand4784

2 жыл бұрын

is it the rope or the mechanism? I would gladly replace the rope if that's the issue

@andrewmasten1235

Жыл бұрын

@@ethand4784 the tabs around the magnet broke on mine and if you dont notice and keep riding, the whole compart looks like it was in a war zone

@derpydog1008

10 ай бұрын

I almost bought a pull start kit. Wow thanks for the heads up dodged a bullet.

Cool

Does anyone know if these pull starts will fit the 100cc bike motor ?

hey my bruvva! ive got 1 of them "100cc tdr motors" is there a pull start 4 them? & if so could u please let me know where u bought it & the exact name of it! cheers bruvva

i have the same bike, can u pls make a video on converting the granite peak to disk breaks? it would be greatly appreciated

@barriosbuilds7688

3 жыл бұрын

I did, but it didn’t turn out well. You just need a bracket and a basic disc break kit. I might try it with my other bike because I don’t think those rims were made for the standard U break setup.

I need this for mine so cold to start it

I see you with the new carb got one of those and they work great

@omargdottin

3 жыл бұрын

I just order one of those too, replace the oem that came with the engine

@HighMileageOffroad

3 жыл бұрын

Unfortunately those carbs are trash compared to the genuine mukini vm18 carbs trust me get ya one and some jets from www.treatland.com and thank me later! I'm running 52mph with mine along with a g2 reedvalve and windowed piston she pulls and screams without a Jack shaft kit.

@vincent10717

2 жыл бұрын

I hate them, mine did not work out of the box. I like their design more than the older ones, but I needed to purchase an older one to get my engine to run right.

First!

hello guy.What is Motor sprocket otherside partition tool name ?

Where did you get the shift kit? Every time I try to start my new 100cc kit the old chain would break as I pop the clutch as the motor tries to start so I got a better chain and that one jams up because it tries to pop off the drive sprocket when trying to start it. No matter what I do with changing alignment it still does the same thing so I hope that would help me.

@zachdillon275

2 жыл бұрын

@@LugiThePainDrinker what part is the flower nut?

@karltaylor4847

Жыл бұрын

Slowly release the clutch as u peddle I have the same problem but get a bit of speed up peddling

I have one just struggling with the original carb any ideas guys please ??

Do any of you guys know what site that I go to to order the rear drive sprocket for the mag rims there's two one on each side

@jccornerstone

Жыл бұрын

Did you ever figure this out having same issue

En donde se pude compra me podes decir si no es molesto es claro

I like that start puller

@barriosbuilds7688

2 жыл бұрын

Don’t not worth it

I was wondering if I could pull off a pull start from a broken weedeater or something and try to use

@barriosbuilds7688

2 жыл бұрын

Same here, but even a weed eater has a better pull start design than these.

do have hold the clucth when pull start ? how does it work. My clucth gear box is damage inside this metho can it sovle the problems ?

@YoMotab

4 ай бұрын

yeah you have to hold in the clutch or you're gonna have a very hard time pull starting it

How long did Your's last?... Every One I ever bought broke in the first week.. I've taken the old cases and made Better components and upgraded IT..diy style.. Now, If I'm Building for Someone else, & They want The Pull Cord.. I'll Take Off The Crappy Catch Wings & replace Them From Jump ... For My Off Road Builds.. I Mix some 2 Part Epoxy and Lightly PAINT It on the various components and let it dry before re-assembling.. Just too try & re-enforce The CHINA Quality of The Parts.. BUT, Only A VERY Light Coating.. Seems To Work Well?.

@barriosbuilds7688

2 жыл бұрын

3 pulls

@Fred_Zepplin

2 жыл бұрын

@@barriosbuilds7688 .. Yeah, Ya pretty much need to upgrade them right out of the box.. If Ya still have the broken ones.. try and fabricate the broken parts.. You can do It With basic tools.. jig saw..angle grinder and a good hand file, As well as maybe drilling out the rivets and use some small stainless steel nuts/bolts.. They will work Pretty good after Modding Them.. But, Cheap Junk Out of The Box.. Thanks For Sharing Bro... Keep On Rippin' !!!

@barriosbuilds7688

2 жыл бұрын

Too much work for something that should work right out of the box… went back to stock.

@Fred_Zepplin

2 жыл бұрын

@@barriosbuilds7688 .. Yeah, Most just take it off and put the original cover back on.. A Pull Cord is handy to not pedal.. But, If Your bike is set up well, 3 or 4 "Pedals" and You're off to The Races Anyway.. I Liked The Pull Cord on Chopper Builds.. They're Crap to pedal, A Pull Cord is nicer imo. .. A Mountain Bike.. Pull Cords are not really needed.. The Choppers were made for Engines.. Most were crap To Pedal..lol. True Tho! .... Stay Awesome Brother !!!

@JadedNegotiation

Жыл бұрын

@@Fred_Zepplin yep can agree the stingray shoppers are shit to pedal. my kill switch falls apart then gotta pedal 2 miles home

Where did you get those crank arms? That's what I need, my crank arms is always bumping into my exhaust pipe 🤔

@barriosbuilds7688

3 жыл бұрын

They came with the jackshaft kit, but I believe it’s just the standard wide crank set.

@itsthebart9050

3 жыл бұрын

you can heat the exhaust pipe and bend it out of the way

Naw bro. You left out the parts that I’m having Trouble with. How did you get your case to go back on because I seen you having problems with it and how did your boat get so long that you can put the nut back on it

I have the same bike with the same motor

With a normal pedal will the pedal rotate

@catsnponds5959

Жыл бұрын

No

@dash_amazingcool2314

Жыл бұрын

What pedal can I get so I can pedal without it hitting the push starter

@catsnponds5959

Жыл бұрын

@@dash_amazingcool2314 extend your crank arms

do you have to have a pull start if you have the shift kit

@barriosbuilds7688

2 жыл бұрын

Yes

@Westhelockpicker

2 жыл бұрын

@@barriosbuilds7688 if there was a way around that I would be getting it

@barriosbuilds7688

2 жыл бұрын

If there was a way around it, I would be buying another one!!

I hope you gonna put the wires away from the exhaust pipe

I’ve always just pedddled and mine to start it up

How much did those nuts cost

Does that mean you can't use the spark plug that much anymore

@ogjacob

2 жыл бұрын

😐

@ogjacob

2 жыл бұрын

😶

@napsum9255

2 жыл бұрын

Aww, no it still need the spark plug.

@ogjacob

2 жыл бұрын

@@napsum9255 thanks 😊

@TacticalPhoenixYT

Жыл бұрын

Bro what💀

I'm about to make it so my can be started my a drill

is it easy to cold start it?

@barriosbuilds7688

2 жыл бұрын

Yes! If it doesn’t break.

Lol you all know how that pull start ends up shortly after!

@barriosbuilds7688

2 жыл бұрын

Broken

... почему не поставил гроверную шайбу под гайку,- со временем открутиться от вибрации?!!

id much rather have bump start than that pull start

The only problem with a pull start is it will Waller out your keyway slot for your magnet & cause f***** up timing issues. That bolt and keyway slot was only designed to hold the magnet in place, not the torque required to turn over your motor. It will work but over time you will produce more slop in the keyway slot causing timing issues.

If you want to know how to make your engine do 50+ comment and I'll help ya I've been building these engines for 2 years and know what I'm doing! I know what does and doesnt work on these engines and wiold be glad to help ya get your speed fix!

@tonypagan8852

3 жыл бұрын

Im just starting out on this motorized bikes and id like to know hiw to make them faster

@HighMileageOffroad

3 жыл бұрын

@@tonypagan8852 do you have Facebook messenger?

@codenamethecleaner7519

3 жыл бұрын

I’d like to know! Please. Tailored Detailing on Facebook

@jcodaniel5678

2 жыл бұрын

I am interested. I don’t have a Facebook but I do have messenger

@sevensavage7905

4 ай бұрын

very late comment but you would you be eilling to help me as well

Ok u w to remove the pedal start set up just to add the pull start

@barriosbuilds7688

Жыл бұрын

I had to use the wide cranks… but it wouldn’t let you pedal start anyways.

Ya chain spring clips wrong way round m8 ! X

Why are you making such a big deal out of it being painted or not?, spray-paint is cheap, lol, was the jack-shaft worth the time and money or not?

@barriosbuilds7688

3 жыл бұрын

Yeah I’ll paint it, Jackshaft worth the time no but for the money. It’s okay, just a lot of finicky parts to deal with.

@HighMileageOffroad

3 жыл бұрын

Dont get a jackshaft kit take it from me I've been working on these for 2 years and my single speed 66cc is currently hitting 52mph with ease! Wanna make your run the same message me and I'd be glad to help!

@andrewmasten1235

Жыл бұрын

@@HighMileageOffroad I had my 80cc anbull at 35 and switched to a 36 tooth sprocket, tuned the carb a little rich with no air filter and only got to 43mph

@andrewmasten1235

Жыл бұрын

That was a month after I put the motor on and iv been rebuilding and trying to figure out how to do my port timing since.

Ya exhaust will snap off unsecured

What part number is this

@barriosbuilds7688

3 жыл бұрын

Didn’t know there was a part number. Just bought it off Amazon.

@erdenetugs2958

2 жыл бұрын

@@barriosbuilds7688 can u take a link

The pull start...meh, but that watch band is 🔥🔥🔥🔥🔥🔥👍🏾

My motor. Is a 80cc motor for my bike cycle

how does your bike not leak un burned gas and oil all over it

@barriosbuilds7688

5 ай бұрын

I mean I had some leaks but make sure your head gasket and base gasket aren’t torn. Because that can cause oil to leak everywhere.

Sooo... did you have any timing issues???

@barriosbuilds7688

2 жыл бұрын

Yes I did, actually I think this is the reason the motor stopped running. It plays with the timing.

used an m18 drill to drill start my motor and i completely stripped the magneto nut lol

top speed ???

@barriosbuilds7688

Жыл бұрын

This bike only went about 25mph… but after all the upgrades I did, now tops out at 37mph.

@dragos_daniel_.1064

Жыл бұрын

Verry good speed

I'd pin those wires away from your exhaust

so u don't use the pedals anymore......mmmm

@barriosbuilds7688

Жыл бұрын

Nope…

That's a Trek

Spray it black

Centrifugal clutch? Pull start? Done that. No, thank you.

The pull start I had exploded after 1 day

@barriosbuilds7688

2 жыл бұрын

Happened to me 3 times… finally gave up on them.

Você falou e falou e não vi nada de interessante. ..

theres no point of having a pull start, u can’t ride it from a complete stop, u gotta start pedaling regardless to accelerate

@barriosbuilds7688

10 ай бұрын

The pull start was for the jack shaft kit, witch both are a complete waste of money. You can’t start a bike with a jack shaft kit by pedaling. But after replacing 2 pull starts, I threw away the whole jack shaft project. The straight chain drive is way more reliable.

@user-zx1rt8ed5z

2 ай бұрын

Yea you can you just don’t know how to

@user-zx1rt8ed5z

2 ай бұрын

Yea you can you just don’t know how to