nice buddy

@HLModTech

Жыл бұрын

Thanks Joe!

nice

@HLModTech

Жыл бұрын

Appreciated. Now I just need to figure out what to cut next. =)

Great video! Does this laser cutter cut sheet aluminum?

@HLModTech

Жыл бұрын

How think are you thinking? I will see what I can find out. Thanks for the kudos too!

@r.j.sharkey

Жыл бұрын

No, the smallest CO2 laser that can cut VERY thin aluminum sheet is 150 Watts and even then you need a specialized cutting head with a high pressure air assist to quickly remove slag. You can probably etch anodized aluminum but not cut it with this. Aluminum is one of the hardest materials to cut as it's reflective to CO2 wavelengths and is very good at dissipating heat. Even a 400W CO2 can only cut 1.5mm aluminum sheet. To do it properly you really need an industrial grade fiber laser.

@HLModTech

Жыл бұрын

Thanks for the info! Most of my are with cardboard and wood.

@phethomakhadi5415

Жыл бұрын

@@r.j.sharkey thank u

Does the machine come focused, and if not do you have a video showing this?

@HLModTech

9 ай бұрын

It does not. Mine was close enough to get going. I do not have a video for making it better though. There are quite a few out there though.

I ordered this same k40 that is supposed to be lightburn ready but lightburn is not recognizing it when I scan for device. Do you have any suggestions. Thank you in advance

@HLModTech

Жыл бұрын

That is odd. I would make sure you have it powered on, and then make sure the usb cable is connected correctly. I had worked in dark areas where I have tried to stuff it in a HDMI port before.....

@wtrujillo7549

Жыл бұрын

@@HLModTech thank you for your response I found the problem was that i had it connected to my tablet which wasn't powerful enough to recognize it, so as soon as I switched it to my PC it worked fine. Thank you once again

@HLModTech

Жыл бұрын

Awesome! I will keep that in my list of things that could be the issue.

Is 3 passes on cardboard a bit much? I would think a single pass would do it.

@HLModTech

Жыл бұрын

Possibly. Since it was my first cut... I was definitly learning. I am still mastering being able to adjust the power with the dial. I will keep tinkering. =)

Did you need to align the mirrors?

@HLModTech

Жыл бұрын

I did not for that first cut. It is always a good idea to do so though.

@phethomakhadi5415

Жыл бұрын

@@HLModTech u mean not to align u just use it as default

Can you please show us what your grbl settings are?

@HLModTech

Жыл бұрын

You bet. Working on it now.

@HLModTech

Жыл бұрын

I will post the vid in the morning. Footage is recorded. I did note that I do show you pretty much the same stuff in this video. kzread.info/dash/bejne/q56H2Nt7YZmyfrQ.html Is there something different you are hunting for?

@HLModTech

Жыл бұрын

Just posted. kzread.info/dash/bejne/rISulaenZauYdps.html Let me know if you are really hunting for something else.

Can it surface engrave anodized aluminum parts?

@HLModTech

Жыл бұрын

I am not sure. The only marking I have done on metal was using laserbond.

5:21 I have a question. My tiny display near the yellow test button says "laser signal off" and I don't know how to turn it back on. Can you help me fix that?

@HLModTech

3 ай бұрын

I have never had that issue. I would contact Monport Support. I am curious if maybe there is a wire lose or something though.

How would you compare it to XTool M1? Other than price?

@HLModTech

5 ай бұрын

They are different technologies. Co2 lasers (Monport) are generally more powerful. The XTool is a diode laser. When diode lasers are listed at 40w, they are usually stating that their laser cuts as well as a 40W laser. The bed of the XTool is quite a bit larger. I am not sure how the software works with an XTool, but I would guess it is pretty plug and play. Aligning and such with the Monport is work. I like the power, but go to my diode machines more often.

hello everyone. I have a problem with my Monport 40w. When I send the job, the laser does not fire and since I turn it on, laser signal off appears. When I press the test button it barely marks the wood. Does anyone know what this is due to? I must clarify that the machine is new

@HLModTech

8 ай бұрын

Have you checked the alignment of the lasers. I do not have a tutorial for it, but there are a lot out there.

Hello, so I need to do multiple passes to cut?

@HLModTech

2 ай бұрын

It depends on what you’re cutting. I do some trial and error with each project.

@cubansli3099

2 ай бұрын

@@HLModTech 3mm Plywood. Thanks for your time

@HLModTech

2 ай бұрын

I bet 3mm could be a 1 pass project. I have found though that 2 passes usually gives me a cleaner cut if their are crazy corners and such. Still trial and error for your numbers. I have not cut wood with mine yet.

@cubansli3099

2 ай бұрын

@@HLModTech Thanks I tried that, I think my machine is having issues, it will not go above 16mA. I appreciate your time

Can this laser cutter cut through the National Debt?

@HLModTech

7 ай бұрын

We need more power Scotty... 😉

@thecentralscrutinizerr

7 ай бұрын

@@HLModTech Dammit Jim, I'm given her all I got! 🤣

@HLModTech

7 ай бұрын

Glad that connected. The kiddos I taught before I retired would not have had a clue. =)

Hl Modtech I've been watching you for a long time and I am huge fan, can i get your autograph? I know i may have more subs but that means nothing. Everyday I watch your content and I just love it, I was nervous because I was about to post a comment about your other vids but It was probably going to embarrass me. I have a few questions for you- if you don't mind answering then pls do so. What made you become a youtuber & what challenges did you overcome? Explain in 5 sentences... I have other questions- How do you make your own youtube vids & what do you enjoy doing as a content creator? I know this may be weird but I want to get to know who you are as a content creator, I'm not looking for personal information but I'm looking to connect with you if that's alright... I will be asking you questions every day btw- so yea. what is your biggest challenge in life and what is your advice to others about overcoming their fears,challenges and more etc?; How long do you plan on being a youtuber? - Those are all the questions i have for you today, I hope all is well in your life and I will he heading off now; If you have any questions regarding everything I said then feel free to ask me any.

@HLModTech

Жыл бұрын

I'll try to answer one per day... I became a KZreadr becuase it helped me share my content efficiently. The mantra has always been "What will you learn today?", so I always like to share something. Daily is a lot, but I seem to always have something to share... =-) Did you see today's Short yet?

@HLModTech

Жыл бұрын

The challenges for me on KZread were getting past the 1000 sub and 4,000 hrs watched requirements. It took a ton of patience and about 3 years. Getting used to seeing me on cam took a bit too. Initally I just was trying to have great lessons for the classroom... now I take a minute to make sure I am reasonably ready for the cam. 🤣

@templex1615

Жыл бұрын

@@HLModTech Next questions: How do you define success, at least for yourself? What kind of legacy do you want to leave behind? What fears are connected to your pursuit of success? How have you faced them? What realization has changed your life or your perspective over the past five years? Have you ever abandoned a social media channel, not because of opposition to your views but because that opposition came from others?

@HLModTech

Жыл бұрын

My success is when I get a note from somone that my videos helped them be successful. The comments, emails, or even when I was in the classroom and was able to witness someone being proud of what they had accomplised is what I ♥.

@HLModTech

Жыл бұрын

As far as my legacy... Either the mantra What will you learn today? or Let's get crackin. =) Of course I would ♥ to be remembered for having tutorials that were clear, fun, & worth the viewers time.