Just done this fix and it works! Finally that annoying rattle is gone!

Thank you, this rattles drive me crazy i figured it out also after many attempts to find the source and your solution is great ! Even the service center couldn't point were the rattles coming from

Excellent problem solving and thank you so much for the fix. I hope Tesla is taking note of these tiny design flaws that their owners are finding for them.

Thank you for taking the time to make this video. You solved my backseat rattle and your video gave me all the steps necessary to fix it.

Two years with this noise! Thanks so much for the solution!

I've had this issue since Nov 2018. Now, it's gone! Thank you!

Fixed my issue as well ! Was driving me nuts. Thanks so much

Had this problem too. I just used felt tape and wrapped it around and between bolt on seat that worked great. Thanks

Thank you so much for this video. I had this same issue and got it fixed after taking it to Tesla four time. Which of course they said it was within spec. Final took it apart my self and it’s good to go now.

This is epic. Shame Tesla didn’t do this themselves to begin with. Well done! 👍

Thank you for posting the video and showing the design flows. The rattling noise was bothering me a lot. Finally will fix it!

The Expedition/Navigator with 3rd row seats has the same problem on the smaller side of the seat. A plastic 1/16" thick washer between the bracket bolt took care of the problem. Great troubleshooting video.

Thanks for this fix video. My 2019 had the exact same issue. Fixed it in about 30 min.

Have very similar sounds in model y produced 12/2021. I’ll attempt to take a look at these areas. Thanks for posting video. When my kids sit in seats, sounds go away which makes sense.

Wonderful! thank you!

Adding a shim can move the bench to the side a little bit and cause it to scratch the metal hooking mechanism from its side. That will cause a new squeaking noise after doing the fix in the video. If that's your case make sure to check it out and add extra material on the side of the hook so it doesn't scratch against the plastic.

I had the same rattle issue. It took a long long time to find the rattles came from that hinges.

This is da video. Good work! Rattle fear us!

This is helpful but how do you get to the removal?! Can you post a video. I'd like to fix my rattling!

thank you

Good video. bracket was for sure a problem.Center sleeve was still in place. I used a rubber washer to eliminate slop in bracket.Lube also. I also added 1/2" foam insulation along top bracket where top of seat clamps in place. Placed on metal inside cover. Solved problem.

@adrianturingan3612

Жыл бұрын

what rubber washer size did you buy? thanks

@xtremerazor7618

Жыл бұрын

What year model 3 is yours?

@jharn79942

Жыл бұрын

@@xtremerazor7618 2018

@noyb9284

4 ай бұрын

What size rubber washer did you use?

Thanks for the video! I'm trying to find my missing calipers, do you happen to have the exact measurements so I can design the washer, or better yet, the STL that you've used?

Thanks you for the video, can you post the 3D file ?

Did the noise happen when your seats were folded down?

how do access the side latch where you put the washer? think i have the same problem but not sure how to access it

How did you take off the seats?

How did you get to the bolts on those seats? I'm struggling, same issue.

@KiloDoubleMike

2 жыл бұрын

The leather covered parts that the seatbelts lay on pull off. They are apparently called C-pillars covers. Might need to look up How to remove them.

Great video! Is there a video that can show how to actually remove the rear seats?

@pfarris86

2 жыл бұрын

I am looking for this too!

@fredhamilton1701

8 ай бұрын

kzread.info/dash/bejne/oIiAtMObm9eshMo.html

@fredhamilton1701

8 ай бұрын

@@pfarris86 kzread.info/dash/bejne/oIiAtMObm9eshMo.html

How's it holding up?

Can you post a video on how to disassemble the seat completely? A lot of us don’t know how to to get to the component without showing a start to finish. Thanks! :)

@KiloDoubleMike

Жыл бұрын

Yeah, sorry for just getting back to you. I actually need to do mine again. The sleeve fell off again, but I’m developing a solution I hope to share soon.

@MeshModeler

Жыл бұрын

Looking for a video as well

@Trackaddik

Жыл бұрын

Same Herę, sens to be no vids on how to remove the rear seat backs. Would really help.

@yangsunee1911

Жыл бұрын

same here. I’m lookkng forward to see it.

@thunderbuddy93

Жыл бұрын

Def looking forward to your video!! Would love to permanently fix this

Great video. Could you share the file please? Or at least the washer dimensions... Thanks!

What year is this m3, mine is 2021 and doesn't have the bracket in between the seats I did all spots you mentioned and still can hear a tiny rattle any advice?

@KiloDoubleMike

2 жыл бұрын

2018

@KiloDoubleMike

Жыл бұрын

I’m sorry, I just read the whole comment. I’m not sure on the newer models, I’m sorry.

Szia Mike! I experience a similar rattling, or rather a DUMB CLICK in the backrest of the left front seat - when starting off - only sometimes, but still very disturbing!!! Do you have experience with this? When I stand on the lumbar support, the DUMB CLICK does not appear for a few days... b/r.

@chrispetrillose

Жыл бұрын

I have this too. Trying to figure out what it is. Have you figured it out?

@csipszerviz

Жыл бұрын

@@chrispetrillose It does not click in certain seating positions. I don't feel the pin joints are the source of the problem. I haven't seen a video of a disassembled seat yet.

Was removing the trim pieces on the side of the seat to expose these bolts easy to do? ty

@KiloDoubleMike

2 жыл бұрын

Man, I am terrible at responding apparently. Sorry about that. Yes it was pretty easy, Just pull from the top and they pop right off.

@billnipp2309

2 жыл бұрын

@@KiloDoubleMike that’s ok. Thanks. I was able to pop it off

@Brice_Cassa

2 жыл бұрын

@@KiloDoubleMike Was it difficult to put them back in place?

@billnipp2309

Жыл бұрын

@@Brice_Cassa a bit.

Do you happen to have a before video? I have a rattle that is any money the same as yours.

@xtremerazor7618

Жыл бұрын

Please share video of rattle if you have one. I’m trying to narrow down rattle in rear seat/rear deck area as well.

Hello I have the exact same issue and I am not very confident with the remove process of "Bolster - Side - Seat - 2nd Row ». Th service manual says that the pastic bracket (Bolster - Side - Seat Clip : 1111033-00-E) is a "one time use only ». Please can you help with the remove and install process ? You seems to have managed to do it wihout breaking this bracket. This rattle drives me crazy !

@KiloDoubleMike

Жыл бұрын

Give me a few days.

Hello, what is the diameter of the washer? nylon or plastic? Thanks

@KiloDoubleMike

Жыл бұрын

I’m not sure. I’ll get back to you on that

Could you publish a 3d models of your prints? or give a link? Thank you!

@KiloDoubleMike

2 жыл бұрын

I'll try to remember to do this once I get home. I'll throw the link in the description.

@InsleepTech

2 жыл бұрын

@@KiloDoubleMike Were you able to publish them somewhere? Having this same issue and would love to 3D print the washer you made

🎉

Can you please share the 3d print drawing for the washer!?

@KiloDoubleMike

Жыл бұрын

www.printables.com/model/433662-model-3-rear-seat-washer-fix

@yessuz

Жыл бұрын

@@KiloDoubleMike great!!! Did you make the removal of rear seats video as well? :)

@KiloDoubleMike

Жыл бұрын

@@yessuz I’m sorry, I have not. However this video should help at around 4 min 23 sec you get to see it get put back together. That should show you enough. kzread.info/dash/bejne/oKJmz6SrernLltI.html

Does the rattle sound high pitch? I have similar movement. But my annoying rattle sound high pitch like plastic hit metal sheet.

@KiloDoubleMike

Жыл бұрын

It can sound like that sometimes yes.

@kinhung

Жыл бұрын

@@KiloDoubleMike just remove the seat and the rattle still here but Tesla has followed you to make that plastic piece in the middle. mine is 2021 model 3.

@KiloDoubleMike

Жыл бұрын

@@kinhung You mean that sleeve or that the sleeve now has a flange on it? The sleeve was stock, I hope they updated the design for that purpose though.

@kinhung

Жыл бұрын

@@KiloDoubleMike got the original rattles fixed by tesla, is trunk trim and they said they lubricate the rear seats. however, they just make new rattle from the joints of the rear seats. I can press the seats to make the noise now

@kinhung

Жыл бұрын

@@KiloDoubleMike back from tesla, door panels rattle gone by replacing new clips, D pillar rattle gone , they reinstall something. but they just give me the exact new rattle from the back seat in your video. try to solve it myself some days.

Hi can you share the .stl file or the exact dimensions of the washer please ? Thank you for the help

My sleeve was so sloppy I had to put electrical tape on the rod so it wouldn’t go into the seat, if you 3D print the sleeve I’ll be your first customer

@KiloDoubleMike

Жыл бұрын

I’m actually designing a lip that will stop this from happening. I’ll post a vid soon.

@anonymouspranco8882

Жыл бұрын

@@KiloDoubleMike - what’s the status on this? Thanks 👍🏻

@h1ghland3r

7 ай бұрын

​@@KiloDoubleMikeHas the new video been posted?

Obviously Tesla ain't watching this because my 2 week old 2023 M3 is having this issue

Tesla should pay you or hire you as QC specialist.

$50000 car. LOL

Tesla should get sued for all this bullshit rattle and squeeks.

Clearly stupid Tesla design! Teslas drive great but all the rattles make me want to sell mine!

Tesla is a terrible company. You shouldn’t have to create your own fixes for their poor designs

@MichaelCena08

Жыл бұрын

Terrible company? No. Poor design? Yes.

THANK YOU. My seats move up and down about 9 thousand feet each direction, I BET this is the problem. Thanks a ton, I'll report back when I fix it. Also have an insanely annoying squeak that I cant find, maybe it's on of those bushings.