Келесі
- 33:49
- 58 М.
- 00:20
- 31 МЛН
- 12 күн бұрын
- 00:33
- 49 МЛН
- 19 күн бұрын
- 00:18
- 17 МЛН
- 2 күн бұрын
- 00:33
- 60 МЛН
- 4 күн бұрын
- 17:35
- 150 М.
- 3:56
- 130 М.
- 15:34
- 1,2 МЛН
- 11:34
- 107 М.
- 9:06
- 46 М.
- 0:30
- 14 МЛН
- 0:39
- 1,4 МЛН
- 0:13
- 3,8 МЛН
- 0:37
- 3,1 МЛН
- 0:57
- 1,9 МЛН
Пікірлер: 41
Really interesting - Thank you. I hope the new bearings last as long as the original Miele one's.
good video, after 17 years I changed the bushings, I needed a 2 arm gear puller to free the spider. Also when you disconnect wires from the heater element, there is a white plastic piece. above it with a rubber hose plugged into it. remove this hose. It's the water level sensor. This is a rewarding job, but a time consuming one. It also saves you a lot of money. I would change shock absorbers and put new brushes in the motor while you have it apart. Make some notes and take your time
@ritarajczi6132
2 жыл бұрын
Please help me! How much kg of clothes can it take? I have searched all over the internet, but nothing.....
@AndreaNegri-gl9fh
Жыл бұрын
@@ritarajczi6132 5 kg / 47 litre volum
@Martindyna
5 ай бұрын
After doing all that work, which I admire you for doing, I wonder how long e.g. the Programmer will last. This may be why Miele say it's uneconomic to change the bearings. P.S. I wonder how much a new programmer would cost. These days you can of course design your own PLC based programmer if you're that way inclined.
Holy macaroni, you took out the whole thing. I have a Miele W 149 toploader. I hope i won`t have to take the drum out when replacing the bearings.
Wow I'm impressed! Only that I was waiting for the moment you would remove the door seal I don't know why but.... And know I need to look further how to take it out.
Thanks!:)A little over an hour.But I did not at once but in stages. I took it apart the machine and then waited one day until the arrival of the bearings.
@thumbsdownbandit
5 жыл бұрын
Took me 10 hours
Hi!, very good video!!, In the past my grandma had one (the grandma who has the bosch), they are a very good washer, Thanks for uploading this vid!!
I don’t think you checked the inner drum spider... worth doing - I think mine is making mine off axis and rubbing on door seal (and this is causing rumbling noise). Bearing I think is fine. Apparently the aluminium ones corrode...
Good! I do it now also with my W723 :-D
Wow. That was a great job. Thanks for showing us :)
Can you please help, I can't seem to knock the drum right through the bearings?
I have a Miele 3035 washing machine. I pulled out the inner drum by accident, the drum was off axis and make a lot noise. What should I do? Please help me, thanks!
Your motor needs servicing. Replace the bearings and using a commutator stone helps. A better bet would be to replace the motor bearings, lathe the commutator until it is round and use a seating stone to help bed the new brushes in. It can be difficult to remove the pulley from the motor.
Where is the inner drum spider ?
Szervusz! Szuper a video, koszonom a segitseget, pont ezt kell csinalnom a Mutterom gepevel. Add meg, legy szives, a csapagyak es szimering adatait, koszonom!
@siemens130
8 жыл бұрын
Szia!fejből nem tudom de ha kiveszed úgyis meglátod.
Уточните модель или модельный ряд Miele, с силуминовой крестовиной. С уважением!
The motor bearings are not in bad shape.Were oiling.The commutator has been cleaned.The engine has been cleaned of excess coal dust.Only I did not show it!:)
Thanks!:)
it's verry good vid's!!!
Well done but I could hardly see anything.
Good stuff, better than my bosch 2008 model with plastic water drum outside , a mega job complete demontage of all units. ?.........
@siemens130
9 жыл бұрын
Yes.
Its like bauknechtboys style
Good video to fast to follow
😎
good video, but too fast to follow
hej, use never a hammer to drill in the bearings whith an other hammer, the hammers may have the same hardness and will explose easly! beware. jean michelle jarre´s pop corn?
@siemens130
10 жыл бұрын
Yes,the music is pop corn.
как называется музыка?
@siemens130
9 жыл бұрын
Pop corn
You took one hour then you must know what your doing then pal.
fucked up sounds
Des Video is ve de Fisch do sixt nix wos a duat
Wie Sie sehen, sehen/sahen Sie nichts...
hej, use never a hammer to drill in the bearings whith an other hammer, the hammers may have the same hardness and will explose easly! beware. jean michelle jarre´s pop corn?