This is the perfect tutorial for beginner AFR Target

Great tutorial. Makes life a lot easier

We really do appreciate it! Your videos are second to none!

@TurbineResearch

Жыл бұрын

Thank you ! I’m glad they are helpful

Commenting to help the algorithm

@TurbineResearch

9 ай бұрын

Thank you 🙏

@jamieem37

6 ай бұрын

Also beep beep stustustu

Thanks!! You make it look easy. Keep up with the great content. We appreciate it.

@Suicid3mx3

Жыл бұрын

thanks dude! comment on every video you watch!

excellent intro to the theory and the software

Awesome job.

love your megasquirt videos! keep up the great work 🍻

@TurbineResearch

Жыл бұрын

Thank you !

Amazing thanks for making this

Holy afr tuning batman!! 😳 give me the beans!! Love the video!! Way to good 👍 👌

Thank you for your videos I watched the one about warmup enrichment and got it idling perfect. But can't seem to get the after warm-up right and it stalls on its face unless I apply a little pedal and it idles up and afrs are 14.5/14.7 and once I let off the gas at idle it stalls. I have an 02 NB2 1.8 vvt with a speedyefi ecu stock 265cc injectors.

Very useful, thank you!

@TurbineResearch

Жыл бұрын

Thanks 🙏

Love your easy and knowledgeable videos, I have a question in "General settings" the "Incorporate AFRTarget" is that good to leave off while tuning or leave it on, I've heard you should leave it on otherwise if you change afr's you would potentially have to change your VE table also, just wondered if you use or know more on that setting.

Good work

Excellent!! Please keep making these Megasquirt video's. And if your looking for some subjects to cover, can you explain the purpose of the VE table?

@TurbineResearch

Жыл бұрын

Thank you !!! The quick answer for the VE table is that it's used to calculate the required fuel based on the volume of air ingested into the engine as a percentage out of 100. It's the fuel table to map how much fuel to inject at any given load of the engine.

So I have a question. Does the mega squirt go by the AFR table or the fuel table. Or is it the mega log viewer compare the AFR table and change the Ve table? Cuz I'm having a strange issue where it was running great at like full throttle it would be more rich but now after the car was sitting for a while if I get on it it gets really lean like around 17 to 19 ish and now I'm afraid to drive it!

Nice 👍 Have you thought to do a video on a vvt table ?

No impact of narrow band or wide band sensor ..?

Hi. yjank you for the video. i like to ask you if you know the funtion of the ambient temp sensor.. One mpre question. I have a LS1 maf. tp put with my 4 cilinder 8psi volvo. i see no one knows about this two questions. i have my volvo siiting for more then a year now. i like to learn atleast the basic tuning and move the car from point A to B

I have a 89 Fox I just bought. Has been turned in FL. I'm in TN. On3 and many extras. Ran a AFR of 11.0 at one point of high rpm. Thoughts!

@TurbineResearch

Жыл бұрын

If you’re turbo 11afr sound fine

Could I use this table for e85? And not coming vert everything to lamda. I don't really understand lamda

@TurbineResearch

Жыл бұрын

Yes you can use this for e85 as long as your wideband is on the gas scale and calibrated in tuner studio

I have been fighting to get the AFR table to control the AFR ratio correctly. All your videos have been massively helpful! I have done the best I can to give the Megasquirt the correct information from my Innovate MTX-L plus, even going to custom mode with voltage values. I have had the motor dyno tuned, also used tuner studio to set fuel values. I have the "use AFR table" set to on. Still the AFR is not even close to the table, and I literally destroyed 3 pistons from detonation as the Megasquirt is not following the AFR table. I'm not sure what I did wrong. (or the dyno tuner) Advise would be greatly appreciated! (I have contacted Megasquirt, with no reply, and asked on their tech page, but only got vague responses) (1994 Mustang Cobra 363 ON3 turbo)

@TurbineResearch

Жыл бұрын

There is a lot that could potentially be wrong with how things are setup. You might need to have someone tune the car that specializes in MegaSquirt products.

@johnnydanger57

Жыл бұрын

@TurbineResearch that's actually what I did. The dyno guy said he had been working with megasquirt systems for almost 2 decades. He changed the tune a bunch, but the data log was still not following the afr table. I tried again to find which of your videos showed the full set up on getting the afr table to control the fueling. But you have so many it's hard to find the exact one. Thanks for the reply!

@h3atn3n

11 ай бұрын

@@johnnydanger57 did you find out what was causing your issue I'm having the same issue I have a Miata but I have a speedy efi and I change the afr table but it doesn't change I also tried to adjust the duty% and the amount of time the injectors are open by like 2 MS to see if it changed it didn't at all

@johnnydanger57

11 ай бұрын

@h3atn3n83 I found out the afr table is pretty much useless as an adjustment table. They are just calling it a reference table, whatever use that is. It's your fuel table that needs to be adjusted to get the correct afr.

@Elturko1982

7 ай бұрын

Thanks ❤

Hello.Do you not know what data to enter when setting up the bmw vanos on the m52tu or m54?

@TurbineResearch

Жыл бұрын

Check out @pazi88 for more information on m52 and m54 tunes

@user-fy6cc3sq3f

Жыл бұрын

thanks

Any differences on a 1000cc turbo motorcycle AFR table?

@TurbineResearch

11 ай бұрын

You want to use a dyno to be safe but this table will be a good safe starting pint. A turbo 1000 must be nice !

@H-M-78

11 ай бұрын

@TurbineResearch I actually have a 1300cc with turbo kit. (Hayabusa gen1) The stock fuel injection is untouched and using extra injectors in the plenum. It's running a little bit too rich so I started try using Tunerstudio recently

@TurbineResearch

11 ай бұрын

@@H-M-78 that’s awesome 😎 nothing in my mind is as wild as a turbo hyabusa

@H-M-78

11 ай бұрын

@TurbineResearch yes, its pretty fast for streetuse, about 300 hp to the wheel. Only using a spacer too lower the compression and some harder clutch springs, that's all. Question: when using autotune there's a checkbox "update controller" Does "checked" means that the corrections running in real time?

@TurbineResearch

11 ай бұрын

@@H-M-78 do you have an instagram or KZread with videos of the bike ?