In part 2 we discuss pan lubing bullets with homemade lube and sizing them with the Lee Bullet sizer.
Жүктеу.....
Пікірлер: 36
@duelist195411 жыл бұрын
If you use the Alox lube, you should swab the bore after every shot, otherwise you will quickly (within 10 rounds) develop a hard, crusty, baked on fouling that will ruin accuracy and be a real bear to clean out. I lube for black powder with a 66% lamb's tallow/33% beeswax mix, but 50%-50% olive oil to beeswax works well too.
@james_lessick8923 жыл бұрын
Thank you for this video, I'm gonna do it this way for sure.
@duelist195412 жыл бұрын
@decimadimencion I use a combination of lamb's tallow and beeswax
@martindl9911 жыл бұрын
Nice one Mike.
@duelist195411 жыл бұрын
Anything less than 1200-1300 fps is ok. I use it for 124 grain lead bullets inn 9mm
@dennisfischer8765
3 жыл бұрын
Hay.. I'm new at this.. I'm going to try it on my p89.. THANK you
@duelist195411 жыл бұрын
Sure
@Relowder3313 жыл бұрын
Its for smokeless. Ok ill try increasing the wax tmrrw and see if it helps. Thanks for the reply.
@duelist195413 жыл бұрын
@Relowder33 OK. If you are shooting B-P that is a poor combination....sludge builder...Smokeless powder...OK. Try rubbing the lube into the grease grooves. If it wipes out easily try increasing the paraffin content...you need more wax in proportion to your soft lube.
@Relowder3313 жыл бұрын
50/50 parafin wax and vaseline, tbl spoon of stp oil trtment and a crayon for color.
@duelist195413 жыл бұрын
@Relowder33 What is your lube made of?
@BZHprepper11 жыл бұрын
Hi, just watched pt1, now pt2 : ) How often do you need to clean the sizer? Does it get leaded or stay clean? Thanks again. Now to pt3.
@duelist195411 жыл бұрын
I've not had any lead build up at all
@jeffshootsstuff13 жыл бұрын
If it doesn't matter if you get lube on top of the bullets while in the tray, why not just dump the lube in from the cup? Thanks for another great vid.
@echo1er11 жыл бұрын
thanks. I'm using a lee bullet mold and the grease grooves doesn't seem deep should I just liq alox it.
@duelist195413 жыл бұрын
Ordinarily I'd be a lot neater. Ideally the tops of the bullets should be clean, but working around the camera with such a small pan just messed me up. The reason not to just pour in the melted lube is because the pressure of pouring it in can knock over some of the bullets.
@swordman509 жыл бұрын
Do you lube your 44 cal. black powder conicals?
@echo1er11 жыл бұрын
how long do you keep the bullets in the pan lube?
@chalder111 жыл бұрын
Is it possible to pan lube the lee micro band bullets?
@Relowder3313 жыл бұрын
Ive started to pan lube but my lube is not sticking to my lube grove. Any advise?
@echo1er12 жыл бұрын
where do you get bee's wax from
@Ensign_Cthulhu11 жыл бұрын
Okay, so you might need to buy a new Lee sizing die for every calibre, and you might need to prelube, but: how much do sizing dies for the RCBS or Lyman lubrisizers cost each? And prelubing surely makes things more flexible, at least for shooters like you who might switch between BP, high-V and low-V smokeless & have different lube recipes for all these things. All in all, it seems like Lee wins out on all counts. Is there anything it can't do?
@duelist195411 жыл бұрын
Until the lube cools and hardens
@dillonpalen633911 жыл бұрын
can you reuse the lube
@mickmoriarty54428 жыл бұрын
I am about to use your lube for my ROAs, 45ACP and ultimately my 9mm I pick up the lithium grease tomorrow and my friend is an apiarist and keeps me supplied with clean beeswax. I also shoot 44Mags, mostly with 44Specials, but I also like to load full strength loads and I am also about to load for a lad that bought a H&R Shikari off me. He wants full strength loads as he will be hunting pigs and goats. What can I add for the extra velocity, or can you recommend a different formula. Sticks of lube run $AU8-$AU10 here :(
@DickTickles7 жыл бұрын
Mike, when you pan lube and size using the Lee sizer, do you have to re-lube those bullets like you had to in part 1 when using Lee Liquid Alox?
@duelist1954
7 жыл бұрын
Dick Tickles Nope
@DickTickles
7 жыл бұрын
duelist1954 That is... Awesome.
@duelist195412 жыл бұрын
I get mine from Mannlake Ltd
@GarandGuy25533 жыл бұрын
I'm thinking of using 50% beeswax/50% Crisco shortening. Any thoughts on the Crisco substitute for the white lithium grease?
@duelist1954
3 жыл бұрын
It is not a very good choice. Crisco has a very low melting and burning point. You would be much better off using olive oil.
@GarandGuy2553
3 жыл бұрын
@@duelist1954 Thanks! I’ll have to give that a try.
@michael1842723 жыл бұрын
Will these sizing dies work in a Dillon 550 machine?
@duelist1954
3 жыл бұрын
You can try. I'm not sure how well the Dillon shell holder will hold the ram.
@otunca11 жыл бұрын
Oh my God , am I see right in this video ? Are you for real (duelist1954) ? Have you informed about lead poison ? I will never put lead bullets near or on my kitchen counter . Also I suggest you use latex gloves when you handle the bullets Other then that this is a good video ...
Пікірлер: 36
If you use the Alox lube, you should swab the bore after every shot, otherwise you will quickly (within 10 rounds) develop a hard, crusty, baked on fouling that will ruin accuracy and be a real bear to clean out. I lube for black powder with a 66% lamb's tallow/33% beeswax mix, but 50%-50% olive oil to beeswax works well too.
Thank you for this video, I'm gonna do it this way for sure.
@decimadimencion I use a combination of lamb's tallow and beeswax
Nice one Mike.
Anything less than 1200-1300 fps is ok. I use it for 124 grain lead bullets inn 9mm
@dennisfischer8765
3 жыл бұрын
Hay.. I'm new at this.. I'm going to try it on my p89.. THANK you
Sure
Its for smokeless. Ok ill try increasing the wax tmrrw and see if it helps. Thanks for the reply.
@Relowder33 OK. If you are shooting B-P that is a poor combination....sludge builder...Smokeless powder...OK. Try rubbing the lube into the grease grooves. If it wipes out easily try increasing the paraffin content...you need more wax in proportion to your soft lube.
50/50 parafin wax and vaseline, tbl spoon of stp oil trtment and a crayon for color.
@Relowder33 What is your lube made of?
Hi, just watched pt1, now pt2 : ) How often do you need to clean the sizer? Does it get leaded or stay clean? Thanks again. Now to pt3.
I've not had any lead build up at all
If it doesn't matter if you get lube on top of the bullets while in the tray, why not just dump the lube in from the cup? Thanks for another great vid.
thanks. I'm using a lee bullet mold and the grease grooves doesn't seem deep should I just liq alox it.
Ordinarily I'd be a lot neater. Ideally the tops of the bullets should be clean, but working around the camera with such a small pan just messed me up. The reason not to just pour in the melted lube is because the pressure of pouring it in can knock over some of the bullets.
Do you lube your 44 cal. black powder conicals?
how long do you keep the bullets in the pan lube?
Is it possible to pan lube the lee micro band bullets?
Ive started to pan lube but my lube is not sticking to my lube grove. Any advise?
where do you get bee's wax from
Okay, so you might need to buy a new Lee sizing die for every calibre, and you might need to prelube, but: how much do sizing dies for the RCBS or Lyman lubrisizers cost each? And prelubing surely makes things more flexible, at least for shooters like you who might switch between BP, high-V and low-V smokeless & have different lube recipes for all these things. All in all, it seems like Lee wins out on all counts. Is there anything it can't do?
Until the lube cools and hardens
can you reuse the lube
I am about to use your lube for my ROAs, 45ACP and ultimately my 9mm I pick up the lithium grease tomorrow and my friend is an apiarist and keeps me supplied with clean beeswax. I also shoot 44Mags, mostly with 44Specials, but I also like to load full strength loads and I am also about to load for a lad that bought a H&R Shikari off me. He wants full strength loads as he will be hunting pigs and goats. What can I add for the extra velocity, or can you recommend a different formula. Sticks of lube run $AU8-$AU10 here :(
Mike, when you pan lube and size using the Lee sizer, do you have to re-lube those bullets like you had to in part 1 when using Lee Liquid Alox?
@duelist1954
7 жыл бұрын
Dick Tickles Nope
@DickTickles
7 жыл бұрын
duelist1954 That is... Awesome.
I get mine from Mannlake Ltd
I'm thinking of using 50% beeswax/50% Crisco shortening. Any thoughts on the Crisco substitute for the white lithium grease?
@duelist1954
3 жыл бұрын
It is not a very good choice. Crisco has a very low melting and burning point. You would be much better off using olive oil.
@GarandGuy2553
3 жыл бұрын
@@duelist1954 Thanks! I’ll have to give that a try.
Will these sizing dies work in a Dillon 550 machine?
@duelist1954
3 жыл бұрын
You can try. I'm not sure how well the Dillon shell holder will hold the ram.
Oh my God , am I see right in this video ? Are you for real (duelist1954) ? Have you informed about lead poison ? I will never put lead bullets near or on my kitchen counter . Also I suggest you use latex gloves when you handle the bullets Other then that this is a good video ...