LS Standalone Harness 101 Beginners Guide | HOW TO Wire a LS Swap Hotrod Engine
Автокөліктер мен көлік құралдары
This time on SPPTV I do my best to pass on the knowledge I have gained through the years building over 20 stand alone LS wiring harnesses. I am no professional and you should do your own research before jumping into a project like this, but I have never had any problems.
Re-Wiring a stock GM truck wiring harness is intimidating if you are new to this kind of thing, but it is relatively simple if you follow some steps. The best advice I can give is to do things in sections. Focus on one part of the wiring harness at a time and then tape it up, put it to the side, etc. .
In this video I show how you can convert a factory Silverado wiring harness to be used in a LS swap vehicle of any type. I cover the pcm connectors and de pinning. Removing connectors and un-needed wires. Power wires and which wires to connect to outside sources, and more.
Check out my video I made on HP Tuners
• HP Tuners 101 Beginner...
JOIN THE SWEAT PANTS POSSE TODAY! SMASH THAT SUBSCRIBE BUTTON! ALSO make sure to hit the bell to get notified when we go live.
THANKS for watching! Drop a LIKE if you LIKE! Share with your Friends!
Facebook @ SPPTV KZread
Instagram @ SPPTVonKZread
Snapchat @ SPPTV
PO BOX:
Rob Exner
PO BOX 99900 LX 087 592
RPO GARDEN CITY
WINNIPEG MB R2V 5A2
CANADA
Пікірлер: 206
This might be the best detailed hands on harness set up ever. I'll be saving this video and using it as a step by step reference. Thanks.
@chevycaprice8956
5 жыл бұрын
You should check out lt1 swap he is a master at this
@SPPTVarmy
5 жыл бұрын
I learned a lot in the begining from him. - Mike
@sethhill19791979
4 жыл бұрын
its a keeper
@travis3688
4 жыл бұрын
Will this work for a blu/green harness to a red green ecu?
@SPPTVarmy
3 жыл бұрын
We dont do it for other people, sorry.
Well done Mike. Harnesses were always a challenging and fun project when I built cars.
A lot of good info here. Definitely seems less daunting than I imagined. May have to give this a shot for my dad's 1938 Ford Coupe ls swap.
Lovin the pink ls in the background at the beginning of the video
Great video man, makes me feel alot more confident in my new harness !!!
Great work guys!!!! I’ve been doing some research for a future project and this is extremely helpful!!! Keep up the great work!👍🏼👍🏼👍🏼
Not doing anything ls related but I found the video very informative thank u 👨🏽🔧👍🏽
Awesome job I am going to tackle this job on my ls swap stang thanks for the info
Super clear and well explained. Thank you!
Well done Mike... thanks for sharing.
Awesome explanation/tutorial and resources! Thanx!
Best thing I have found to removing the plastic loom and tape is a sewing stitch cutter. I’m tackling wiring on my first swap in the next few upcoming weeks hopefully it goes smoothly. It’s not a ls but thankfully I am doubling the power over stock and gaining fuel injection
I appreciate your approach, great work
This video plus the ls1swap site will save me a grand easy. Thanks
Great job Mike!
Great job and appreciate all the details.
bro you answered just about ALL my (newb) LS harness questions in less than 1 minute AND you mobo jumboed! Excellent! My 1st move to fi and last thing i wanna do it leave junkyard and be like, oh dang - i should have grabbed this/that - THANKS!! i wanna do a dirt cheap stock ecu (re programmed) 5.3 with 706 heads and a cam spring upgrade - which I WILL vlog cos i wanna do 350, 383 then LS comparison! my 350 is already FAST (it really is) but of course that wears off quick- my buddy got a 550 crate and i wanna whip him with a junkyard build haha
Very nice job man...made that look so easy,,,,..🤘
thanks man, lots of info. nice work. keep it up.
Wish I had your knowledge... you make this look so easy. Killer skills man!
@illduitmyself
4 жыл бұрын
takes time to learn. start yesterday
Great job man! My favorite parts were sharpnicity and the imaginary firewall. (:
Keep up the great info videos, They are very helpful. I also have the HP tuner pro.
Very valuable information thank you for your time.
GREAT vid! Kind of makes me second guess not grabbing harness and ecu when i pulled my motor planning to run Microsquirt. 👍
Subbed! Awesome video. I was scared of doing this, now I'm confident I can tackle er! I'll use the saved money on go fast parts
Very nice!!!! Congratulations and thanks!!!!
!!! Wow thks again for sharin this will help me put this Harness in 1947 Dodge 3 ton water truck with 6.Litre and 4x4 as well Awesome IMFO Can,t waitto get it goin keep ya Posted Keep it up Ya Got this Thks
Thank you for being awesome and sharing.
Great video. I just discovered your channel, good content 👍
Great video.. Very helpful.
Good ass info guys. Dont stop. Cheers from the south
I watch this video anytime I do a harness
Awesome video thank you!
Awesome video thanks buddy
Great video, I too use that same site for the harness that I do. Great source for doing a harness like this. So you boys enjoy Alberta Premium Whiskey with Mountain Dew eh? That's great guys
Just took my harness off, bountvto break it down. First time try this, will keep you updated.
@chevyman217
4 жыл бұрын
Same lol
@kingjoe750
4 жыл бұрын
@@chevyman217 this harness is crazy. I done with the easy part. Now I'm on to the hard part smh
Swapping a 5.3 out of a Tahoe into my 2004 Subaru wrx, this really helped alot!
@anthonycosco7660
4 жыл бұрын
I wanna do this to my Impreza? Did you use the stock subframe?
@lucysmith4242
4 жыл бұрын
did you finish the swap yet?
Great job bro, jam packed full of quality info.
Gonna dive in for my LS swap into my 90 Chevy short van.I did a harness for a Subbie EJ swap into a 87 GL so I know a bit about it.
This was actually very helpful, thank you. Here I am under the dash trying to take apart the harness wondering if I actually need anything that goes past the firewall. It's my first time doing an engine swap, and I'm actually really surprised at how smoothly everything's going. Bolts aren't seized, clips aren't breaking, I haven't bashed my hands or fingers, seals aren't tearing, I keep expecting something to happen and it doesn't.
It all sounded fantastic right up to the point where you have the haul out the multi meter and trace all the power wires that all look the same... it was then I realized I was trapped in a nightmare :-)
@arkansastrey9694
3 жыл бұрын
The struggle is real
Thanks for the info!
Good stuff!
Ty I needed to know everything like that.im putting a 5.3 in my 03 dodge Dakota..
Great video thanks
The video section starting at 20:54 was the best, but camera work too shaky and quick. I replayed it and got the information I was looking for. Like color of wires and quantity of wires. I am new to this. Bought an unfinished LS swap with the engine running, but I want to double check the wire work and make sure all the gauges work. The old gauges are non-op and I am installing a new digital-electronic set up. Feeling overwhelmed but very motivated! Good work on the video and thank you!
thank you glad to know. about to start an ls swap for my 67
Thanks for the effort you put in to create the video.
Thank you man !
Good video
Mike you must be a very patient guy. 🤣🤣🤣
Nice!
I honestly find it easier to de pin entire harness and separate everything. Then plug each sensor in one at a time and adjust length. To wherever your ecu will be mounted. This way you can hide or tuck the harness super easily and it looks great when you are done, also prevents rats nest
@ericjswindle
4 жыл бұрын
Zipties for the win do you buy new pins for the ecu end and if so where do you get them?
Hey Mike, did you ever do a follow up video where you wired up the ends that you cut off from the harness, like the tach signal and wiring the fuse block?
This video is pure gold. Question is what do you do with your computer when you've made a stand alone harness?
Great video, lots of information. Had a question though. What did you do to change from using a MAF to speed density and why? Was this done via the PCM programing and is a stock pcm capable of being reflashed for this? Once again great video.
This makes me so thankful for the simplicity, reliability, and roadside tuneability of my carbureted engine.
@torrypope3218
3 жыл бұрын
Fear of what you dont understand,i used to be the same but FI is very reliable and you can trouble shoot it with a simple code reader.
@arguingwithstupidpeople2047
3 жыл бұрын
@@torrypope3218 What I have discovered is that Millennial types fear and lack understanding of carburetors. What - you think I don't have EFI on my daily driver? But my carbureted car drives every bit as well and has proven MORE reliable with much simpler wiring and fewer sensors to malfunction.
@torrypope3218
3 жыл бұрын
@@arguingwithstupidpeople2047 Im 50 so i know my way around a carb,rebuilt,I dont know ,over a 100.Just saying thaere is an advantages over carb,such as tunability,better fuel mileage and less emissions.
Thanks alot
Thanks sir appreciate it was good to c this ill have to pound this into my marble lol 😆
Thanks for the Vid! Can you de-pin all these and switch from a dbw pcm to a dbc one and it will work? Thanks :)
26 of Albert prime on the table lol 🤙
Good videos just subscribed to your videos have. Question can a 05 silverado harness work with a cable tb i found a harness in good condition for almost free thank you for any info
I have an 05 LQ9 using Lt1 Swap info and have several wires that color does not match ? on Blue C1 connector pin #7/ circuit # 2705 it shows grey GRY color and my wire is Yellow ? still on Blue C1 pin #45 it shows GRY and my wire is Tan ? All other info so far applies but I am confused on what to do with those two wires. Thank you in advance for any help and you vid is the BEST !
Best to use a dental pick to release the tab on connector pins. They can be fragile and you don't want to break any.
I followed your video on rewiring my oem ls harness to integrate with the new holley terminator ecm that controls my high performance engine. My question is, will I have fault codes and reduced engine mode, and if so, what is the fix? Thanks man!
are stock wiring harness good for any kinda weird mods i wana do to my engine?
I need to know if I can remove oil and coolant level without issue on a regular old Silverado not stand alone. Also which cruise control wires can I get rid of
I have a aftermarket wire harness with two ground wires which one has about 5v when I plugged up everything to the battery. Should it have two grounds and should both be grounded to the engine?
Can I cut all the wires out going to the DBW plug I’m also doing DBC swap and need to know before cutting? Thanks in Advance!!
Would this idea work on doing a 97 chevy camaro with a 3800 w/5speed manual and converting it over to old school with a 305 carburetor set up
Mike How did you hook up obd port?
I learned a lot and feel more confident. But am still scared. Now how do you make what you just made plug into my 91 s10
Hey whats up mike. I was wondering if you knew how to make a gen4 6.2l wire harness and how much?
When I am ready for it (haven’t obtained LS yet) what should you charge me to wire one up?
That first time seeing it gave me an anxiety attack but you explained well
I know it's been a while since this video was uploaded but this guide does work with the red and blue harness as well?
Can u use the green blue pcm 5.3 wire harness with dive by cable throttle body ?
Dang I wish I was building a sonic Stang, I still don't know what I can cut or shouldn't for my application. The hardest part about the swap is finding a video of someone that knows what they're doing that's doing the same thing you are. 🥴
How’s it going I have a question, what would I be doing with pins 26 & 29 HO2S B1S1 low signal- off the blue connector.
Do you know what color wire is connected to both the injectors and coil packs My swap cranks but no start seen on a forum some guy spliced into that wire with a 12v relay
Do you have a link to LT1 swap for the pinout guide?
Hi guys, what if I don't pull out the old cable. Can I still start the engine?
You guys know, if I can I put a 2011 5.3 Silverado harness in a 2008 tahoe 5.3 block and transmission with a 4L60E?
Where are you getting the pink wires for the front o2 sensors to the new fuse block? The rear o2 only has pink wires ans they are required to be removed!
Thank u for ur video but it really complicated there a lot of people that are not running ur setup I'm really confused because there a lot of wire u cut off that I have no idea what they look like
Will this harness setup work with a 72 chevelle?
Question on the drive by wire if removing can i still use throttle body cable driven with the 2003 2005 ecm . Thank you so much!!
@SPPTVarmy
Жыл бұрын
I believe it depends on the individual ecm if they have the option. Closer to 2003 the better as it's more likely to be capable of both. If you found an ECM at a Junkyard you may be able to google the part number and find out forsure.
Do you need the fuse box for the ls to run
Hey man what about the fuel pump harness?
Do you have to power each injector ?
How much do you charge to make a 5.3 wiring harness for 1991 chevy caprice classic I have a 5.3 wires harness and pcm and fuse box ??
My question is that I have a 6.0 and a 4l80. Can I go ahead and grab an ECU from a junkyard out of a truck or van with a 6.0 and 4l80?
How does hooking up a different trans work, how does the ecu know when to shift etc
@bradywilliams2666
3 жыл бұрын
He said he's using a powerglide trans. Which is non comp. controlled.
How about where your scan tool plugs up
I have a 79 Trans am im thinking of ls swapping
bank one 02 is the side of the engine cylinder 1 is on ; )
Thanks . I've read some of the comments and you have a few very nasty folks here . Good luck.
On the o2 sensors the rears on the hp tuner is it just turning them off or is there more to deleting them
@SPPTVarmy
2 жыл бұрын
It's basically just setting the ECM to ignore the code by changing the "Check Engine Light". You can tell the ECM to not watch for that error or report it.
Another great video. Do you need coolant temp to run speed density? Does the wideband have to be fed into the ecu? I sent my harness out, and don't have coolant temp in the harness anymore, and my wideband isn't wired into the harness.
@SPPTVarmy
5 жыл бұрын
Coolant temp is needed yes, for multiple functions of the ecm. Your wideband would be completely seperate.
@Zone6G
5 жыл бұрын
@@SPPTVarmy Thanks. The plug that was the coolant temp plug is labeled IAT, and I don't have a coolant temp. Now I have to tear into the harness I already paid for smh. Guess I'm back to checking pinouts.
@Zone6G
5 жыл бұрын
@@SPPTVarmy That video was so spot on. I'm donating next live stream. I checked my harness again. I did have coolant temp and IAT, just both with the same style plug. They both had continuity with their assigned pins.
So, I still have this giant wiring harness laying over the top of my motor. Does each injector really need its own pink wire running all the way from the fuseblock? Any reason we can't splice them all together at the back of the manifold and run one slightly larger wire over to the fuse block?
@theredfishkid
4 жыл бұрын
Ross Rockey kzread.info/dash/bejne/a5WTldmKeMbTj7w.html