LS Wiring Harness Part 5 | Project Rowdy Ep017
Part 5 of the LS Wiring Harness Cleanup will cover the installation of the 4 Fuse Block, Main Relay, Fuel Pump Relay, and a custom 8 pin connector to support dash gauges and instruments.
The goal is to create a Stand a Lone harness that only requires 4 wires to run the engine. There will be additional wires running to the vehicle to support additional features.
Project Rowdy is a restoration on a 1979 Jeep CJ7. This LS Swap Harness is being prepared to be mated back to its original engine: 2001 Chevy Silverado 5.3L LM7 which has just undergone a full rebuild.
References:
- Wiring Harness Research: www.LT1Swap.com
- Wiring Cleanup Procedures: To be published after revisions from this current build
- LS Fuse Block and Relay Diagram: bit.ly/LS_Harness_Diagrams
- PCM and Connectors Pinout Charts: bit.ly/PCMandConnectorTables
Tools and Parts used:
Qiorange 8 Pin Connector: amzn.to/2lNgMW8
Doorman Fuse Block: amzn.to/2kOBR2R
e-Ting 5 Pin Relay Socket: amzn.to/2kOzzRk
Absolute RLS125 Relays: amzn.to/2lNp4gR
Vice Grip Wire Strippers: amzn.to/2lI3fie
Loom Fabric Tape: amzn.to/2xZng69
Here is what I used for the wiring:
- Pink (AWG18) - This was reused from the original harness
- Yellow (AWG16) - Fuel Pump Feed
- Red (AWG10) - Battery Hot
- Purple (AWG10) - Keyed Hot
Project Rowdy Playlist:
• Project Rowdy - Jeep R...
UCanDoIt2 Website: www.ucandoit2.club/
UCanDoIt2 Contact: UCanDoIt2Mike@gmail.com
JeepForum Thread:
www.jeepforum.com/forum/f22/pr...
Facebook Page:
/ projectrowdy
Wire Loom Amounts:
- 1/4" : 16 feet
- 3/8" : 8 feet
- 1/2" : 3 feet
- 1-1/4": 3.5 feet
The 3 smaller sizes I purchased from Harbor Freight (1 pack each) and the 1/-1/4" I found on eBay and purchased 4 feet (by the foot).
Music
Intro: Alex Skrindo (Alive)
#lsswap #lsswaptheworld #lsswapc10 #lsswapc10 #diyperformance #jeep #jeepcj
Пікірлер: 805
The very best information I have found! Doing a LSI into 1988 Chevy K1500. You have helped me understand more and I can understand what you are saying. Worked on cars all my life, always avoided wiring except for radio or fog lights. Excellent information HIGHLY RECOMMEND THESE VIDEOS! I have already found the LT1 wiring diagrams and printed them, the notebook is a great idea, not only for what to do but what was done. I suggest you write a book, can’t find anything that goes in depth enough to help. Thanks so much for you efforts. GREAT JOB! P Hurst
My Pawpaw used to use that "good enough for the girls I go with" line... Told him I seen the girls yku go with... I got warned about talkin bad about Grandma... oops
Video is 5 years old and still helping people just getting into an LS swap. Thank you for this.
"good enough for the girls we go with" HAHA!! love it
Were can I get that fuse n relay set up
Thank you so much for your work. You're doing a fantastic job, and I really appreciate your thorough and straightforward instruction. Im 19, and working on swapping an LS into my car. You've been incredibly helpful. Thank you!
Do U still build ls harnesses I’m Very interested
Can you use a thinner gauge wire on pins 86& 85? Also what did you mount your PCM to to mount it to the firewall?
First, I'd like to say that I feel sad that my binge watching of your series has come to an end.... can't wait for more videos from you. Second, I'm looking to start 5.3 swap\build soon, my first engine build and I'm confident that your videos are going to help me succeed. YOU DA REAL MVP!
Commenting to help with the algorithm
Are you a teacher by chance?
Sir, I've watched your videos when I was in my early 20s not knowing what the hell you were doing. I'm around the corner from 28yo now, built my truck and taught myself quite a bit. I must say you've dumbed down the whole process to where I can accomplish my high school dream of ls swapping an old school car (i got a rust free 85 Fleetwood now). your efforts are much appreciated in the car community!
awesome how you include your son.bonding you 2 will never forget.
Definitely enjoyed this series. Great work and can't thank you enough for confirming my confidence in doing an LS install.
Harness looks great. That looks like a really nice connector especially for the price. We will need something like that for our frame swap. Thanks for sharing.
I wouldn’t have been able to do this harness conversion without your videos. Thank you so much.
These videos are awesome. I love the detail you add while fast forwarding the boring parts.
an EXCELLENT tutorial on doing the 'LSx stand alone' .... clear and concise ... WELL DONE !!
By far one of the most helpful videos/ series I’ve seen in a while. Thanks for the help
Meticulously well done! A man after my own heart 👍🏻