Loads of pals bought these and whinged they were rubbish - so I got one to see. Nope - it's them, not the machine. Running 1mm flux-core, these weld like a little demon - superb IMO. I think the issue is people who can't weld at all buy one & expect to be a champ welder off the bat - I'm a lifelong welder, it runs smooth & strong for me. Hugely impressed in fact. Others bought the Lidl multi-process version that does mma, mig & gasless - and also whinged that the gasless mode was crap - It isn't, it's excellent in fact - I firmly believe loads are forgetting/not knowing to change the polarity before using flux core & then get horrible results, blaming the machine. Once you run flux-core properly, it's a cracking way to join metal - key is to run it properly. The "Thing" people say about excess spatter - that's you, not the process too - set it up right, spatter is miniscule/non existent. Beware that flux core is damn bright compared to gas shielded - use a good mask. For gas shielded I often weld without a mask (loads in fact) - no chance with flux core, a mask is essential - the arc is blazingly bright.

@erik_dk842

Жыл бұрын

You do sound convincing.

@jamesward5721

Жыл бұрын

@@erik_dk842 I weld for a living - I bought one of these ^ just for the "let's see are they any use" factor.

@erik_dk842

Жыл бұрын

@@jamesward5721 I'll pick one up next time they are in Lidl. It's always nice to be able to glue some steel. I have an old 160 amp 400Volt Italian MIG welder in the basement, but the bottle is empty and the wire is one lump of rust. The electrodes for my ESAB 140 are destroyed from moisture. This little feller can reside in a closet at room remperature.

@jamesward5721

Жыл бұрын

@@erik_dk842 Exactly - I now use it when I can't be bothered wheeling a big hefty MIG to a piece of work - I just pick up the nice light flux-core, plug it in, weld, chuck it back on the bench. Very handy.

@WickedCerberus

6 күн бұрын

Could you please add more info about proper setup with little to no splatter?

This tiny welder is just amazing. I got it a few days ago and instantly started challenging it. I love it. With this tool you think twice to use screws or just weld it right away. IMHO welding had never been simpler than that. The intelligent current- and wire speed algorithms takes over all the struggling of adjusting them yourself. If the power is not enough, then just turn it a little up. It also seems to have shortcircut wire burn off feature. So that if the wire is melted together with the workpiece, the current is turned up to melt the wire away, and push new wire out rapidly until new arc is ignited. I saw this only on my Fronius Transsteel 2200 before. So very nice machine! Safety: Beware to always wear FFP3 mask and have a fire-extinguisher / water sprayer in reach.

@davidwaterhouse2552

Жыл бұрын

I don't even know what an ALGORITHM is??? Can you weld with it? I have been welding since 1979 when I was 15, so not easily impressed! (Coded for five years in 1995) but don't even work in the industry anymore, but am restoring a Classic MGBGT car and VW T4 Campervan!

@patintermatroskin3650

Жыл бұрын

Водой тушить электрические соединения ? 😂😂😂

@dr.-ing.andreaskeibel3722

Жыл бұрын

@@patintermatroskin3650 Well, possibly Russian electric Welders frequently catch fire. But here it is meant to be prepared to extinguish secondary fires, caused e.g. sparks, or dripping iron, or dropped hot parts...

@cromyjr9183

10 ай бұрын

@@davidwaterhouse2552 You coded for 5 years without even knowing what an algorithm is ? And you are proud of it ?

@davidwaterhouse2552

10 ай бұрын

@@cromyjr9183 No I don't know what an Algorithm is ? Please tell me cos I have managed all my life without knowing what one is, and perfectly managed all types of welding! Where did I say i was proud of it????

This material seems very powerful for a small price ! I think it is the essential tool for carrying out daily life. The result is excellent !!!

today is 28th April 2024. I have just bought one of these from Lidl in Wales UK for £79.99, and having watched this video, I am absolutely amazed that it coped with 12mm steel. I was going to be content with maybe 4-6 mm, but this video has made me even more please I bough one (I got there early and they only had three units to sell -so very very happy) ps £79.99= €92.42

@woodworksolutions6365

Ай бұрын

I get mine in Leicester today,

you doing great Job ! Thank you😊

Thank you , perfect as usual ✌✌✌

Great video

Pedazo de soldaduras. Felicidades al soldador: tú sí que llevas kilómetros de soldaduras.

Thank You very much...Turbo Schneider.

It did the 12mm good, flux core very bright and loads smoke, l still prefer stick, but l was a coded welder years ago, but for odd jobs these are fine.

@Zanderman2000

3 күн бұрын

For home use this seems more reasonalble than stick welder, that is, if you dont build ships at your yard.

Thanks for the demonstration. Would be nice to have a clamp-on ammeter indicating how many amps are drawn from the socket outlet at each setting in welding each thickness of steel. This because many people have limited circuit breaker amp ratting. I for one have 220V , 15A in my garage.

@MrWeeds

Жыл бұрын

This is what im looking for too , can I do small welds from the 16 A in my apartment , or do I need to use this somewhere else everytime .. :P

@DVSONENL

5 ай бұрын

​​@@MrWeeds change to 16A C type breaker.

@evanleebodies

2 ай бұрын

Shouldn't be a problem, at 2400 kW, the theoretical current draw will be ~10A.

Sinceramente estoy sorprendido con esta maquina tenia una de electrodos y no soldaba bien no soy profexional pero desde que uso esta me considero un artista por las soldaduras fantasticas que hace es una verdadera maravilla 😅😅

does it support spot welding ? i mean not continues like in your example ... thank you

Nice 🛠️🛠️🛠️

Me gusta la máquina hace una buena labor

Thank u

Ok felicitări ❤❤

those welds are amazing man , for 100 euro , damn !

@a.f.838

Жыл бұрын

€78 in Portugal, today ✌️

Great video, you did a great weld using this (didn’t expect a clean finish, other videos show splatter and messy result) do you still prefer the previous pmsg model ? Would be nice to see strength test or projects made by this pifds model. Keep up the good work

Just ordered one to do the sills on my car.

Can I use "PARKSIDE® cored wire »PSFD B1«" with this device?

Hallo Herr Welding . Vielen Dank für die tollen Videos sie sind sehr hilfreich. Ich habe auch dieses kleine Parkside Schweißgerät und bin damit zufrieden im Hobbybereich ist es top . Jetzt habe ich das Umrüstset für die Fülldrahtdüse gekauft und einen Schweißautomatikhelm einfach um beide Hände zum führen des Brenners frei zu haben. Wieviel Abstand zum Werkstück empfehlen Sie beim schweißen mit diesem Gerät 1cm ?

Is there such a thing as flux core for welding aluminium or does that need gas mig?

,спасибо за информацию...много искр, много дыма, много мусора

So, out of the box , is this welder set up with +ive earth [recommended for flux core]? And, if not, can the polarity be easily changed? I couldn't see from the video how the terminals were attached inside.

@evanleebodies

2 ай бұрын

It is DCEN, it is a permanently fixed polarity and cannot be changed as it is a FCAW-only machine

шов наложит любая сварка..а вот какое качество соединения?

Is it ok for car body work? I heard that only gas one will do good job

Perfect¡¡¡¡

When starting to weld how far out do you have the wire, do you strike on the copper tip then before the wire feeds out, or do you strike the wire that is out of the tip. If so how far out has the wire to be to strike and start welding. It's difficult to see on your video.

@AndySlug

5 ай бұрын

Using this welder, im around 10-15mm from the weld area

Can you weld copper, brass, aluminium...'?

Pero que belleza 😊

Very good on new metal,like to see our it work s on rusty or greasy metal or

@joeduffy3309

4 ай бұрын

Anyone that knows how to weld would clean the welding area first

привет! нержавейку можно варить?

How big a generator need to be to run it ?

Hi how much this welding machine for Australia

Is it good?

👍

12mm ! formidabil ! va rog,un bilant al costurilor intre sudura cu fir si cea cu electrozi cu invelis !

Nice, one query if I may; is the welding current ac or dc? May be someone can help.

@ninonaputu

2 ай бұрын

DC ofc

From where i can buy extra tips?

Can you welding with Inox please send me your answer

Is it true that after a few minutes of use it shuts down to cool itself? Can you give a fast answer? Thanks a lot for your time

@turboschneider6407

2 жыл бұрын

That is not right.

@brianhowe982

7 ай бұрын

No, mine has never shut down

@nickolassiranidis107

3 ай бұрын

Φιλαράκι καλημέρα το πήρες το μηχάνημα?

Jojo na rozbalení jsou potřeba rukavice😂

How does this work without gas? The wire have protection for it self?

@adrianpolley9419

3 ай бұрын

It's a hollow wire with the flux built in. You have to set the tension so as to grip but not crush the wire when feeding it in.

Hola De cuantos watios de potencia es la soldadora.

What is the thinnest metal it can weld without blowing holes?

@davie2191

Жыл бұрын

0.8

@paulcureton5834

10 ай бұрын

Iv just welded a wing patch work on lowist wire speed it has the thing is you cant hold the torch more than 2sec other wise you blow holes metal 1mm thick i weld all the time, bad idea on the brass tip showing as you will arc the metal if your not a good welder and the wire will arc to the tip bad idea i made a cover over mine from a old mig welder works alot better saves alot of problems only bought it saves me carrying a great co2 bottle and welder up the garden to do some small jobs

Nice video, nice tool, but do you have any idea what is the type of the gun and where we can buy consumables ??

👍👍👍👍👍 👍👍👍👍👍 👍👍👍👍👍 👍👍👍👍👍

Can I actually run this machine from the washing machine outlet ? It runs from the 16 Amp breaker , and considering that this machine pulls at maximum power just around 17 Amps , it should be fine for welding small pieces , right ? Help would be really appreciated on this one , cheers Thank you

@aftenstjernemix

Жыл бұрын

I maxed this machine out welding on a tractor implement, using 1mm wire, and the highest setting (above 3mm). It did not throw my 13Amp breaker. According to the manual the breaker/socket must NOT be above 16 Amp. Enjoy.

@evanleebodies

2 ай бұрын

On a 240V supply it should draw no more than 10A at max power

@MrWeeds

2 ай бұрын

@@evanleebodies Cheers buddy ! Thanks for the help .. I bought the machine a while ago , but can only use it at my parents house , I live in an apartment so I can't use it without being irresponsible and it's also ilegal in my country . Still thanks for the help .. And yes it works just fine in both 10A and 16A breakers

Excellent demonstration of the strength of the machine. I am really considering to buy one. One question: does it also weld stainless steel?

@jojoletoucan5722

Жыл бұрын

With stainless steel core flux yes 😉

Got one today £60 :)

Just bought one yesterday, anyone tell me why my wire pops once on contact and doesn't feed ?

Hallo kann man mit gerät auch alu schweißen? LG Heinz

@dutchsailor6620

Жыл бұрын

Nein

Next week in Lidl 129,99€. There goes 11% inflation. My math isn't good any more.

@telemachin

5 ай бұрын

I got it for 79€ in 2022

@KingofKings-vo4ui

3 ай бұрын

Я вчера купил за 100€

@mrlukaaaaaa

Ай бұрын

Do you need co2 for this tape of welding?tnx for answer​@@telemachin

@andreibaditoiu

Ай бұрын

Got it for 72€ today.

@WickedCerberus

Күн бұрын

139€

Türkiye den bu cihazı nasıl alabiliriz

Hi to you all. I have one question; how long can you weld whith this machine till its power shuts down for cooling? Because i have one welder ( also cheap) and you work with him for 10 min and then gets disconected for 15 min for cooling,because its overheat him self😒😒...thx for the answer.

@unitsol5759

2 жыл бұрын

I was welding with this machine this week for 2 hours and never shot down... Its a value for money for home works...

@giorgos2804

2 жыл бұрын

@@unitsol5759 Φίλε μου μήπως έχεις ιδέα για ανταλακτικες μύτες ;

@unitsol5759

2 жыл бұрын

@@giorgos2804 δεν έχω ψάξει καθόλου, όταν έρθει η στιγμή να ψάξω αν βρω κάτι θα επανέλθω

@giorgos2804

2 жыл бұрын

Ευχαριστώ φίλε μου, αν μάθεις βρεις κάτι κάνε τον κόπο και γράψε να ξέρουμε.

Praice ?

Tengo q comprarme una me hace falta para hacer puertas.

Can 10mm material be welded? Thank you

@jojoletoucan5722

Жыл бұрын

I'm not sure. Just 120amp, no gaz. 6mm is the max I think

@robsonenduro3316

Жыл бұрын

watch video so you will know.

why this machine haven't gas input？

@MrLatek2

2 жыл бұрын

This is flux/fcaw welder not mig/mag

@dr.-ing.andreaskeibel3722

2 жыл бұрын

This machine is specifially made to be as tiny and as easy handable as possible, and for this to be used only with flux cored no gas metal arc welding.

Ce prețuri au sau un nr telefon

كم السعر مع التوصيل

£145 in the UK

Encore faut il pouvoir se procurer ....... à chaque fois qu'il passe en magasin même de bonne heure il y en à plus ???? même dans d'autre magasins de la région , cette année et l'année dernière , c'est pas normal .

A incercat cineva să îl folosească la reparatii auto? Poate suda tabla subțire?

@78kipris

Жыл бұрын

Sudează table subțiri ,doar că trebuie să iei fir subțire și să practici un pic până ți se dă mâna pe niște bucăți de tablă. E fiabil fiindcă face arcul scurt, ni ai nevoie de gaz cum e la mig sau tig ( tig-ul pt table subțiri E excelent, doar că e mai greu cu buteliile)

je trouve que les buses s'usent vite?!!! et savez ou les commander? LIDLL n'assure pas!!!!! j'ai aussi trouvé un peu chiant le changement du fil !....causant une perte assez longue! mais c'est peut etre? mon ignorance!?

ΠΟΣΟ ΚΑΝΕΙ ΑΥΤΗ Η ΕΛΕΚΤΡΟΚΟΛΙΣΗ

120A मीग मसीनका रेट कीया हे भैया हम आऐगे आप कहासेहो कोनसा सहेर 🇹🇯

Just got my today 109 euro in Ireland lidl.

2 ай бұрын

heh, in Latvia we had the same sale on the weekend, got one miself too :)

Does anyone know if electrode is DC+ or DC- ?

@evanleebodies

2 ай бұрын

DCEN

Cele mai urâte suduri se fac cu acest tip de aparate! Adevărate mizerii! Toate care folosesc acest procedeu, nu în mod special acest model sau această marcă, fac niște suduri cu foarte mulți stropi in jurul cordonului de sudură! Spray-ul pt a rezolva problema stropilor ,,rezolvă" parțial problema, și pe lângă alte inconveniente, creste prețul la consumabile. Costul pt sudură este triplu față de procedeul standard MMA, iar calitatea și aspectul sunt îndoielnice!!!

@felix807

2 жыл бұрын

corect, dar ca pf e greu sa faci rost de gaz. cu gaz iese o minunatie! cu mma nu am reusit sa sudez grosimi mai mici de 1mm, cu asta e jucarie!

@ilovethetruth2130

2 жыл бұрын

@@felix807 Adevărat, e greu dar nu imposibil! Depinde și de localitatea /zona unde stai. În apropiere de zone industrializate cum sunt București, Pitești, Ploiești, dar nu numai, poți face rost de Co2 f ușor, mai greu de găsit este argon sau corgon! Acum depinde și de ce fel de sudură, de ce calitate a suduri ai nevoie! Pt ceva fără prea mari pretenții, o sudură în regim mai puțin decât hobby, merge... Sudura MMA cu electrod, nu se folosește la tablă! Mai ales dacă e sub 1 mm! Mai bine asamblezi cu prindere în nituri sau nituri pop! Depinde unde și la ce folosești sudura cu fir plin. Este un procedeu pt cei ce vor să facă ceva singuri și nici nu au prea multă experiență /îndemânare, bani de investit în aparte bune, performante, și desigur nu în spatii /ateliere închise, neventilate! Procedeul de sudare, în sine produce mult fum toxic, dar acesta cu sârmă plină, e tăticul tuturor!

@florindodan1848

Жыл бұрын

Pentru mici lucrari in gospodarie ..e bun..timpul la sudura cu electrod mma s.a dus....stropii care mai sar se pot indeparta usor.....

@felix807

Жыл бұрын

@@florindodan1848 eu am făcut un antreu pe structura metalică și la 3 m înălțime nu cari așa un aparat greu. In afară de asta nu uita că sudura mma este mai trainică și rezistenta decât mig-mag și flux!

@ilovethetruth2130

Жыл бұрын

@@florindodan1848 Timpul sudurii MMA s-a dus pt cei care oricum sudura MMA a fost ceva aievea, au avut două mâini stângi la mai multe lucruri, nu numai la sudură! Sudură este o artă, o meserie nu pt oricine! Sunt oameni care fac ai adevărată artă în suduri, iar sudura mig mag niciodată nu v-a atinge performanța/cerințele sudurii MMA! Nu toată lumea sudează o balama ruptă la un gard asemenea sau un fier mai mult mort la o boltă de vie de om sărac!

Are there spare Parts available like the plastic thing at 04:02 ?? Mine is broken

@BunkrMan

Жыл бұрын

It's not plastic, the material the cap is made of is bakelite.

@chuco9113

Жыл бұрын

@@BunkrMan is it durable when welding for anything longer than 10 seconds? I want to buy this welder but this non-metal tip is something that puts me off. Won't it just melt after some longer welding?

مؤشر الكهرباء يعمل ولكنها لا تلحم

120,A ऐ मसीनका मीग मसीन रेट कीया हे भैया बताऐ 🙏🕉️🙏🙏

is it AC or DC current

@ninonaputu

2 ай бұрын

DC ofc

كم.السعر

je trouve que les buses susent vite?!!! et savez ou les commander? LIDLL n'assure pas!!!!!

IL crache beaucoup est il fume pas mal ?????

@Zanderman2000

3 күн бұрын

Of course because it has flux in the wire like a stick welder

Push not drag mate:)

2 ай бұрын

nope, you drag with flux core.

@arekguzik1715

2 ай бұрын

​@yes! You're right. Thanks to you I've learned something new:) thanks buddy👍

2 ай бұрын

@@arekguzik1715 good luck! I've just got my tool, done only like five small lines, so much to learn, thanks YT!

Dam re kamina Dam.

Μπορείς να κολλάει και ανοξείδωτο αν θες μου απαντάς

I can’t find dis welder send me address please

Bien mais vaut pas avoir de pb car le sav est nul à chier !!

😂 ЕЦ цдф и џдфгффдедфффрффф😂😂🎉

120A its is joke. Only 2mm welding

@cestvraimenthorrible3465

Жыл бұрын

So the more Amps the thicker metal you can weld? The metal in the video looks thicker than 2mm though

Dali može dase poruči još uvek aparat

For the price, this is an amazing welder. Had mine for a few weeks now and it welds good straight out the box. However.......if you decide to get one the first thing you should do is remove the existing earth clamp and replace it with a good quality clamp. The supplied clamp is made of poor quality mild steel, I replaced mine with a decent quality clamp with a rating of 200A.

Ok felicitări ❤❤