My guy, you just saved me so much time trying to figure out how to access this door switch! Thanks!!!

@onlineappliancetech

14 күн бұрын

No problem 👍

Took some convincing to get my grandmother to not buy a new dryer. I followed your video and determined that the thermal fuse needed replacing. Saved us a lot of $$$. Thank you!

Thank you so much for this video! It's the best one in KZread for this type of dryer. We had a sewer backup into our basement and the washer and dryer were in up to 6 inches of water at one point. They were in water for maybe 2-3 hours total. We cleaned the washer and it is working fine. Using your video, we opened the top of the dryer, removed the front housing of the dryer with the door attached, and removed the metal housing that the lint trap goes into. That had lint inside that had gotten wet and it smelled bad. We cleaned that up really well, and i dried the standing water out of the casing for the blower. We did not remove the the drum. We cleaned as much as we could reach. We left it to dry overnight and then reassembled it. We had two screws leftover. 😬 Turning on the machine was fine. We started a test cycle, and the machine ran normally except for a constant squealing sound that we had not heard before. Any ideas what might be wrong? Squeals to me often mean a belt issue. I don't feel capable of removing the drum and belt and putting that back on correctly, so i suspect we may need to just call a technician if the problem would likely require removing the drum.

Very well narrated and paced so it was easy to follow. I was able to repair my 2 year old machine using this video. A rodent had chewed through one leg of the broken belt switch. Thank you for your professional troubleshooting tutorial.

@onlineappliancetech

5 ай бұрын

You're welcome!

Fixed my dryer this morning and saved $450 doing it because of this video!! Thanks man!!

@onlineappliancetech

16 күн бұрын

Excellent!

An absolute life saver! Have had a loud thumping for over a year. Couldn’t figure out how to get cover off!

Thank you so much for this literally saved me $1000 after taking apart the dryer realized there was a sock that got pushed into the lint box and blocked that spinning piece.

@onlineappliancetech

25 күн бұрын

Thank you for sharing your experience, I'm so happy I could help you save that $1000!

Thank you so much! This helped me reset the thermal fuse and do a deep clean. The heat is working again!

@onlineappliancetech

3 ай бұрын

You're welcome!

Thanks so much. I used this video to replace 4 drum roller wheels, pulley tensioner and the belt. Parts cost $30 on Amazon and about 2 hours of time which included deep clean of lots of lint. This video saved an expensive service call.

@onlineappliancetech

11 ай бұрын

Glad it helped!

@alexwen2786

6 ай бұрын

Thank you - I also used your video instructions install the $30 Amazon parts kit. The belt / idler pulley portion of your video helped me. My dryer noise turned was a bad roller wheel. Now my 20 Year Old LG Dryer is quiet like new!

@juliocastaneda3805

Ай бұрын

Could I ask you, how did you get the part numbers? I need to replace one of the drum wheels and the reset thermostat. Thank you ..-

Thanks for the content! General disassembly videos are highly underrated. I would've never found those clips that hold the top on, without going about it all wrong.

@onlineappliancetech

Ай бұрын

Thanks for watching!

Thank you so much for this video! I was able to disassemble, thoroughly clean, reset the thermal fuse, and reassemble the dryer after discovering that the exhaust hose had come off the dryer for who knows how long ago.

@onlineappliancetech

6 ай бұрын

Thank you for your kind words! I'm thrilled to hear that my video helped you fix your dryer. It's comments like yours that make creating content so rewarding.

Thanks for the video. I had a ton of lint near where the flame is and vacuumed it all out, reset the switched, and everything works! Thank you for the video.

@onlineappliancetech

Ай бұрын

Great to hear that the video was helpful for you! Keep up the good work!

This video has helped me not only fix my dryer but friends who have the same type. Granted all I did was clean the lent from the coils and the bottom pan but our drying issue of have been resolved! Thank you sir!

@Online Appliance Tech Thank you for the detailed video! Best one I’ve found for LG dryer not heating diagnostics. Our LG gas dryer went out last Monday and I was able to tear it down, use a multimeter to pinpoint the ignition as the root cause, replaced it and the thermal fuse for good measure. Put it all back together and was stoked to hear the gas ignition on the first try! Seriously, you saved my vacation! I start a week off tomorrow for family vacation and we are able to get our laundry done at home now before we leave.

@onlineappliancetech

Жыл бұрын

Thank you so much for your feedback! It's great to hear that the video was useful and you were able to diagnose and fix the issue with your LG gas dryer. Your resourcefulness and hands-on approach are impressive! Knowing that our content not only helped you repair your dryer, but also made a difference in preparing for your family vacation, really makes our day. Enjoy your time off and safe travels. It's heartwarming to know we could contribute to your holiday preparations in our own small way. Thanks for sharing your success story with us!

This was exactly what I needed Thanks!

@onlineappliancetech

3 ай бұрын

Thank you for the kind words! I'm thrilled it was what you needed.

Thanks for this post! I've given up on calling repair techs to fix most of our appliance issues. Its videos like this that make that possible. I have diagnosed our problem, and parts are on the way!

@onlineappliancetech

3 ай бұрын

Glad it helped

Thank you! My repaired cost me $20 and a couple of hours! Much better than the alternative!

@onlineappliancetech

3 ай бұрын

Glad it helped!

Excellent video! I replaced the motor thermostat and thermistor assembly and fixed my dryer. Thank you!

@onlineappliancetech

Ай бұрын

Thank you for the kind words! I'm happy I could assist you in fixing your dryer.

This is an amazing video - you've made my life SO much easier today. Thank you. I'd like this 1000x if I could.

@onlineappliancetech

Жыл бұрын

Thank You!

For those wondering if Model DLE7300WE is opened just like he did in this video. It does, I was able to open this model just like he did in the video. I also had confirmed with LG before trying.

Great video…well presented. I noticed a lot of humidity or standing water gets into my dryer tub when not in use. Guessing it’s just coming in through the outside vent (I am in VA & it’s very hot & humid here), but wanted to know if you’ve experienced this or had any other recommendations to prevent it.

Man! Thank you so much for posting this! This just saved me a repair call.

@onlineappliancetech

4 ай бұрын

You're welcome!

Thank you for this instructional video, question: I did not see the parts numbers list, could you post it please…. Thank you..

Excellent video. Thank you so much for showing us the way!

@onlineappliancetech

Жыл бұрын

No problem! We are happy to help!🙂

Thank you! Saved my day and a ton of money!

@onlineappliancetech

4 ай бұрын

I'm grateful I could help you out. Thank you for your kind words!

I cannot say thank you enough for this video. I would’ve never thought that I could take my dryer apart and fix it, but you guided me through it. Thank you again.!!

@onlineappliancetech

10 ай бұрын

You're very welcome!

high limit thermostat is there a different from the M230 vs M220 Or can I put the Reset one in both spots

Great video. Thank you.

@onlineappliancetech

2 ай бұрын

Thank you so much for watching and your kind words!

Great instruction! Bad heater element was the issue.

@onlineappliancetech

Жыл бұрын

Happy to help!

Great Video. Helped me out alot! Thanks.

@onlineappliancetech

4 ай бұрын

Glad to hear it!

Excellent video. Thank you so much for making this video, it helped my out big time.

@onlineappliancetech

9 ай бұрын

I'm glad the video was helpful! Thank you for watching and supporting my channel.

What about a clean filter code and it is cleaned out I even pulled exhaust out. Everything turns on but when pressed start it just beeps.. nothing happens

Amazing Video!! I have similar model dryer and all my parts seem to be testing good. When I plug mine in the drum light just flashes. Any Ideas? I get 240 volts from the outlet and the plug but when connected to the dryer I no longer get 240 volts.

Ok so my dryer was working and was drying through a te1 so I ordered the parts on Amazon just put them in it did the te1 code once again than I tried it again it works but it has a smell is that normal and thank you for the video it helped me learn how to get to the parts after it took hours trying to take the back panel off lol

@onlineappliancetech

Жыл бұрын

Gas smell or burning smell?

Thanks!

@onlineappliancetech

3 ай бұрын

Thank you for your support!

Outstanding, this saved me, thanks

@onlineappliancetech

8 ай бұрын

You're welcome!

Hi, Will this work on model dle7300we? I and want to make sure this is the same way i can open up this model thank you.

Is there a capacitor in this dryer

In reassembling I, seemed to have melted, the belt, based on smell and the dryer not spinning, is it supposed to go to a specific place?

What is the model number of the dryer you are working on? Getting the little tabs to push in didn't seem to work for me on my LG DLE7060WE.

Thank you for this video! What model number is this? And is the thermistor the red wire that was next to the thermostat when you were checking those ohms?

This is a great video. Thank you so much. I did everything and replaced the thermostat and the thermostat or whatever it is right next to the thermostat, there is no visual damage to the wires. It started working for a few loads and then stopped again with the same error code. I opened it back up and checked again, everything is reading correctly on the multimeter this time so not sure what the problem could be now. Same error. Is it the circuit board itself possibly?

@mikey3000

6 ай бұрын

I meant to say thermistor

@onlineappliancetech

6 ай бұрын

It seems like the Main Control is the issue. Check out my LG dryer video which covers the thermistor problem. You can find it in my LG dryer playlist.

I have this same dryer that's out of warranty, and I'm looking for help to fix it myself. The machine turns on and shows that it's “running” (it even counts down and ‘acts’ like its running a cycle,“. I once got the “NP” error code, but it has since disappeared. I checked the breaker and confirmed that my wall outlet and plug are both drawing 240V. Could this be a belt drum issue, or is it related to the blower housing thermostat or fuse? I'm unsure how to check the latter. I have also done a wifi diagnostics and everything checked out. Any help would be greatly appreciated.

@AlSilva-jx9rh

2 ай бұрын

I replaced the 6:40 thermal thermostat and it worked for one cycle and stopped working. Anyone know why?

@AlSilva-jx9rh

2 ай бұрын

I replaced the thermostat for the motor and it worked for some time. 16 minutes before the cycle was to be completed the machine stopped and was told to check the sensor flow and it hasn't worked again. Any ideas on what is going on here??

im having the d80 fault code i cleaned out the clogg and reset the dryer but code still shows up and the dryer works normal to me but the wife says cloths is damp

@onlineappliancetech

4 ай бұрын

I would have your dryer duct work replaced and vents cleaned.

Thank you for this! But... Ok so I have little arms, can I reach in after taking the blower housing to reach that lil reset button 👀 I know my limits and I 100% don't trust myself to take the drum out 😅

Did you unscrew the back to take the top off

Best video ever

@onlineappliancetech

Жыл бұрын

Thank you!

Nice video how do u test the moisture sensor on that same machine my dryer turns on for like 2 minutes then the clock switches to 1 minute then end on the screen technician came to fix it said the air duct needed to be cleaned but it's clean

@onlineappliancetech

Жыл бұрын

Sounds like air flow? A good way to test is to disconnect the air duct from the back of the dryer and see if it runs longer? If it does great that means it's your vents that would need to be cleaned Also make sure you place a load of damp clothes in the dryer before you test so it can detect them. If none of this helps please send me model number. Best Regards Matt...

Thank you so much for this video! I just need advice if you can, my dryer wasn’t starting, just making the click sound, so I followed your instructions and changed the motor small thermostat which fixed the issue!!! And used one cycle and dried my cover perfectly but then it stopped working again, making the same click sound when pressing start, any theories?

@onlineappliancetech

Жыл бұрын

Seems like you have a blockage, meaning restricted air flow. Check your duct work from your dryer to the wall to make sure it is not bent or clogged up.Unfortunately you will have to replace the fuse again, or you could tap it on its back to reset to save you time. Just make sure you hear it shake or rattle on the inside, That lets you know it's reset. Hope this helps.

@jalealejandra

Жыл бұрын

@@onlineappliancetech ok, I will try this, thank you so much for replying!

@onlineappliancetech

Жыл бұрын

No problem

Great video. My dryer is throwing a te1 error, would you know what this means?

@onlineappliancetech

Жыл бұрын

TE1 is a dryer thermistor error code. Make sure your air flow is good. And duct work is not kink up from dryer to wall. Hope this helps!

@macias2e

Жыл бұрын

​@@onlineappliancetech I checked my duct work, it's all good. I just replaced the thermistor and just got done reassembling the dryer, did a test run I'm still get the same code. Any ideas?

@onlineappliancetech

Жыл бұрын

Under LG Dryer Service Manual under Remarks it states = tE1 error is displayed in the drying cycle or test mode. Replace the Steam Generator, however I would recommend calling a good LG tech to come by and check out and diagnose the problem. Hope this helps!

Great Video! I have a te1 code so after replacing the thermistor and sensors right next to it I still get the te1 code right away. The igniter had a reading up in the 300’s, could that be my issue? LG gas dryer model DLG7301VE

@onlineappliancetech

Жыл бұрын

The TE1 error code on your LG Dryer model DLG7301VE typically indicates a problem with the thermistor, a component that measures temperature within the dryer. This error is often triggered when the dryer does not properly detect or read the temperature. The issue can be due to a few reasons, such as: The thermistor might be defective or damaged. There could be a problem with the wire harness connected to the thermistor, possibly due to a loose connection or a wire short. In rare cases, it could be an issue with the control board that reads the thermistor's resistance. It is recommended to unplug your dryer and check the thermistor and the wiring for visible damage. If there's no visible damage, you might need a multimeter to test the thermistor's resistance. However, please be aware that this requires a level of technical competence. If you're unsure, it may be best to contact a professional to help diagnose and fix the problem. Hope this helps! And best of luck!

@bradlane811

Жыл бұрын

I have checked the thermistor with my multimeter and it was good, I still replaced it but this did not solve my problem. The wires look good so I’m leaning towards the board being the problem. Is there a part number or is this something only a technician can replace?

@linos9457

3 ай бұрын

I have the same problem. Was it the control board? If yes, what is the part number?

Hello My 2-3 year old LG dryer stoped heating recently. I checked my vents and they were really clogged prob from previous owner. I cleaned out the vents and found out about the reset button. Dryer started heating for a few loads but stops heating after a few loads. I have to always hit the reset button after one or two loads. Do you think I should replace the thermal fuse? I’m sure it’s prob hard to say without properly inspecting everything but do you think this is the most common problem? I watched your video and a few others and think it’s something I could do. I just don’t have all the testing equipment to test everything. Thank you

@joeshmo23w

Жыл бұрын

Sorry one more question. The part I am referring to is the thermal fuse that has the reset button. Under your parts link, I see the high limit thermostat that was towards the back and you explained right after. Do you have the link for the thermal fuse connected to reset button or Is this essentially the same part?

@onlineappliancetech

Жыл бұрын

Open the door, turn the drum clock wise, if it is hard to turn you will need to replace roller wheels . Reason why is if your drum is not moving at the right speed due to rollers not allowing the drum to move at the right speed hot air will be trapped inside of the drum and cause the fuse to trip. Also when you replace wheels make sure to clean all air flow inside of the dryer well.

I have model DLE5001W. Door switch has 2 wire connector besides the door switch itself. Can’t seem to find info on where they go. Comment?

@onlineappliancetech

9 ай бұрын

For the LG dryer model DLE5001W, the door switch will have a specific connector that is meant to attach to a corresponding part of the dryer's wiring harness. This is to ensure that the connection is made correctly and safely. The two-wire connector you have should only fit into its corresponding connector in one way-this is by design to prevent incorrect wiring which could potentially cause malfunction or pose a safety risk. If you're not seeing where it should connect, or if the connection isn't obvious, then: Double-check the user manual for a wiring diagram or installation guide for the door switch. Look for any markings on the wiring harness that might indicate the correct connection point. Examine the connectors for unique shapes or color-coding that might match the harness. If still in doubt, it's advisable to consult with a professional technician or reach out to LG customer support directly for guidance.

@rickeykeeton4770

9 ай бұрын

@@onlineappliancetech Gonna look for the user manual today. I cannot visually find another connection for the two wire connector. Thanks for the response. If I can’t find the answer, I may just scrap it for parts. Wire burnt in the cutoff and high limit thermostat has come apart. Both test bad. I might straight wire them for testing purposes since parts seems to have gone up in price so much, and I am a little leery of LG’s.

@rickeykeeton4770

9 ай бұрын

My dumb ass found the connection for the two wires. It fit the drum light. SMH. I am pretty sure I checked for that, but I was just haphazardly placing the the front parts if the dryer in place by hand and in sort of a hurry. I didn’t think the the wires were long enough. Checked again and they are for the light. Reminds me of a few times I forgot to connect lid switches on washers.

Thank you

@onlineappliancetech

11 ай бұрын

You're welcome!

I have the same dryer but mine is electric not gas, the problem I’m having right now is that whenever it starts it just makes a loud humming noise for a second then stops, it doesn’t spin, im not sure what’s wrong with it

@onlineappliancetech

4 ай бұрын

It seems like either the motor is shorted or the blower wheel might be jammed, preventing the motor from starting.

@JuanFlores-nl9nc

4 ай бұрын

@@onlineappliancetech I took apart the dryer and took off the blower wheel, I started the dryer without anything hooked up to the motor, it made the same humming noise, the motor twitch but didn’t spin so I ordered a new motor hopefully that’s the problem, thank you for the information

@mikeking561

Ай бұрын

@@JuanFlores-nl9nc Hey I have the electric version as well it's a dle7001w model, basically the same as in the video but he doesn't go over testing the Motor. I had the same issue you described, when I turn the machine on it makes a humming noise and isn't spinning while everything else seems to be working like normal. How did your motor replacement go, did it fix your problem? And if you don't mind where did you buy your parts. Motor isn't seized and turns easily, machine was pulled out of storage recently and worked for about 3 loads but I thought the motor did sound a little loud, now it did what you described. Thanks in advance I hope I see a reply.

@JuanFlores-nl9nc

Ай бұрын

@@mikeking561 the way I tested the motor by putting the dryer back together but without the drum in it and I use the belt to pull up on the pulley so it’s not pressing the off switch, then you want to turn on the dryer like normal and if you see the motor kinda twitch but not spin then it’s the motor, there’s not much that can go wrong on these dryers

My lg dlgx5681v wont turn off even once the cycle is done. Can you please help me with this?

@onlineappliancetech

Жыл бұрын

So drum keeps on rotating once its done?

@just516in

Жыл бұрын

@@onlineappliancetech yes that is correct

@onlineappliancetech

Жыл бұрын

@@just516in Could be your main MPC not turning off the dryer. Does it turn off when you open the door?

The last few are all reading 0 what does that mean?

@onlineappliancetech

Жыл бұрын

Sorry I do not understand the question? Do you have a digital multimeter? And did you place it on the OHMS settings? If you could tell me what the multimeter said before you place it on the part and when you are testing the part. Please get this information to me and I will try to help you.

coool

@onlineappliancetech

Ай бұрын

Thank you!

My husband replaced the thermal fuse since it had no continuity and it wouldn't start would just click I ran the dryer for like 10 minutes n then it started doing thr same thing clicking and not starting

@onlineappliancetech

10 ай бұрын

It appears that your ductwork may be clogged, causing the fuse to trip. You should ensure that the ductwork leading from the dryer to the outside of the house isn't backed up. Additionally, inspect the ductwork to ensure there are no bends that might restrict airflow from the dryer.

Mama