I learned a lot because I had never heard of the Kegerator. You made a very nice looking product!

@rustydogandco

Жыл бұрын

Thank you! 😊

Nice work. Very clean especially with no visible fasteners in the wood frame. And love the VT shirt - class of 88 myself. Go Hokies!

@rustydogandco

9 ай бұрын

Thank you! I appreciate that. Go Hokies! 🦃

Cool project, thanks!

Ah i see you also made dogerator

Kooler, kegler, barrelator, booler, keggo (ozzie version), coolkeg. 🤔 I know, how about 'Boozer'? 😊

Greetings... You think like a #hotWaterHeater for the overlay? #goodluck #thanks

Nice Job. I want to do same project but with Duo-Tight Lines

@rustydogandco

9 ай бұрын

Nice! Good luck! 😊

@prodanman

9 ай бұрын

@@rustydogandco What adhesive did you use to secure the collar to the freezer? Did you use any hardware other than the corners?

@rustydogandco

9 ай бұрын

@prodanman I used some silicone adhesive that’s typically used for kitchen and bath projects (waterproof). I didn’t use any other hardware for attaching. I just made sure to apply a good amount of weight while the adhesive dried. I left it for about 24 hours before I removed the weights.

@prodanman

Күн бұрын

How's your DIY Kegarator project holding up?

@rustydogandco

Күн бұрын

Great so far! We use it all the time.

I'm not sure about the sensor in the water, because that might cause a delay in the temperature control loop. That means it will be slow to respond when the fridge heats up and keep it running for longer than it needs to. So it might use more power and you might end up with bigger temperature fluctuations than you might want (depending on how the control unit is set up) but see how you go. Awesome build, might have to make one myself someday. Cheers! 🍻

@rustydogandco

11 ай бұрын

I’m going to see how it goes and I might eventually move the sensor. Seems to be doing okay for right now. Thank you! It was a fun build and we have enjoyed having it. Cheers! 🍻

@wedomusic9451

10 ай бұрын

The sensor in the water is smart. Because the temperature of the water will be similar to the temperature of the beer in the keg.

@JeeeezBub

8 ай бұрын

@@wedomusic9451 First I've seen this approach and that seems logical.

Why did you choose 34 degrees Fahrenheit? Also, what's the recommended upper limit? (How high should you allow the temp to go before the unit kicks on)?

@rustydogandco

7 күн бұрын

I like for the beer to be nice and cold! Haha so that’s close to freezing temperature but not too close. I would say the highest temp you would want to go for setting the temperature would be 40 degrees Fahrenheit. 34-40 degrees is kind of the recommended zone but ultimately its up to each individual and how cold they like to serve beer. In my experience…the colder the beer the less issues with foam. Not sure if there is something to that but that’s just the experience I’ve had. Hope that helps!

I am super intrigued about putting the temperature sensor in water. Out of curiosity, have you measured beer temperature right after pouring? And well done...project and video! Edit: And the temperature controller...I don't recall seeing these when I looked at doing this project a long while ago. It seemed like the only ones available had to be hardwired into the freezer. Do you have any thoughts on the that and about your temperature control unit in general?

@rustydogandco

8 ай бұрын

First of all, thanks so much for the compliments! I appreciate that. I have not measured the temperature of the beer when it's poured but that's a good idea. I might try that sometime to test the accuracy of the temperature sensor. What I can say though...is that the beer tastes nice and cold upon pouring haha. The temperature controller that I purchased for this Keezer I got off of Amazon. I'll leave a link to it below. It seems to work pretty well so far. I will have to wait and see how long it lasts. Overall the setup was relatively easy although everything being in Celsius required me to google how to change it over to Farenheit but that was simple to do once I googled how to do it. I leave my temperature controller set to 34 degrees farenheit and it keeps the freezer at that temp. I haven't put a thermometer in there to measure the actual temp and see if it's exact but I'm satisfied with how cold it's keeping the kegs so I feel like it's probably pretty close. Hope that helps some. Here is the link to the temperature controller I use: a.co/d/6r8QWZE

@cecilarchbold

Ай бұрын

Rookie question: So by plugging the freezer into the temperature control unit allows the freezer to operate like a refrigerator?

@rustydogandco

Ай бұрын

Correct! It allows you to set the temperature the freezer operates at so you can run it at a temperature closer to that of a refrigerator.

@cecilarchbold

Ай бұрын

Ahh, so it basically cycles the freezer off when it arrives at the temperature you set.​@rustydogandco

@rustydogandco

Ай бұрын

Yep! That’s the jist of it.

Nice work, I especially appreciate creators who share oopsies too. Please fix your flag though. Stars are always top left.

@rustydogandco

Ай бұрын

Thanks! I didn’t know about the flag issue until some other people commented the same thing. No worries though…I have already fixed the issue. 😊

The flag is backwards