Thank you! I was totally dreading doing mine until I saw your video.

Thanks for posting this.

Great video and explanation. Just picked up the bolts at Ace Hardware and going home to put the clutch and two new tie rods on.

What’s the torc spec on the bolt

Great video! Having a similar issue with a 2019 HPX815E Diesel Gator. Pulled the primary clutch no problem and ultrasonically cleaned it. Clutch compresses and releases by hand but the rollers on the spider that limit the travel of the flyweights are only about 270 degrees complete--is this normal or evidence of extreme wear? I would have expected them to be 360 degrees round... A detailed photo of the ends of the spider showing the rollers would be very useful. Also, has anyone had any proven success with an aftermarket primary clutch? The John Deere parts ought to be called "Dear Parts" because they want $700 now for a replacement AM13887!

Your video was very helpful. Today I had to put a new primary clutch on. But, I am having a issue with that old clutch bolt. Once I got it on and tighten it up, the clutch would have way to much play, i.e. , the clutch would even touch my chain. Do I need a shorter bolt now that the clutch number changed? And, if so, what size and length?

@Hubjeep

3 жыл бұрын

I don't recall the length of the bolt, I think it was pretty long though. Are you using the original bolt?

@davidbridges6450

3 жыл бұрын

@@Hubjeep Yes, but it seems to long for my new clutch because once tightened down, I could move the clutch all the way over to the chain.

Good work, how does it run? great idea with pulling tool set up as well.

@Hubjeep

8 жыл бұрын

Thanks! Drives better than ever, nice and smooth.

Where did you buy the clutch ?

How did this clutch hold up? I just got a 855D and need to replace the belt, and possibly the clutch. Just curious if the eBay clutch held up

@Hubjeep

4 ай бұрын

Hi, it's still working like new! I got it on ebay, it's an OEM part. I put less than 100 hours on my Gator a year.

thanks for uploading where did you get the clutch and how much?

@Hubjeep

7 жыл бұрын

John Deere dealer selling on Ebay. $280 shipped.

@yamaharidr450

7 жыл бұрын

Thank you for posting this video, had to do a clutch on a 6x4 and this really helped me out.

John Deere dealer selling on Ebay. $280 shipped.

Hey man I too have a project gator diesel 6 x 4 and have just been too pre-occupied to get to it. We put a rebuild on the motor and cranked it only to find that it had a warped head. had it shaved and re worked. Not sure what else to do but try myself to fix it. I discovered that I had a bad fuel cut off solenoid. The last mechanic killed the battery and starter trying to start it with a closed fuel solenoid. It has been sitting for 5 years prior but is so close to running. Might need to call on you for advice sometime.

How did you hold the clutch when tightening it to50Nm?

@Hubjeep

3 жыл бұрын

That's about 36 lb/ft, was able to hold by hand/engine compression as I recall.

Do you still have the old clutch

@davidbridges6450

3 жыл бұрын

Yes Sir.

the right tool from jdt1641 john deere parts about $ 40

what was the torque specs

@Hubjeep

7 жыл бұрын

Sorry, I don't remember. Not sure if I came up with a Deere spec, or went with a bolt torque chart.

Just two years later and I cannot find one for less than 500 dollars

@Hubjeep

5 жыл бұрын

WOW, I just searched too, cheapest I saw was $558!!!! I thought $280 was high.

@redetroitwing

5 жыл бұрын

Im looking as well, it's bullshit that they want to rob their customers, I'll never buy another John deer anything

@SilverCanary1

5 жыл бұрын

@@redetroitwing you must not have heard about the engine management software saga and how most US farmers have pirated diagnostic software as JD wouldn't sell it to ANYBODY but themselves. I think they've rescinded that but probably now charge double for parts instead, lol. I just want to keep one running for a bit and pattern service parts are pretty reasonably priced in the UK at least. Don't forget though - as with every vehicle - to service them properly and regularly or you're in a world of pain. Stuff like blocked airfilters (these have 2) can wreck piston rings, etc. and cost more on fuel as well as make it slow and smokey. Clutches are £500 here btw lol...

@Miniaturehorseexpress

4 жыл бұрын

@@Hubjeep you can rebuild them for $33 bucks

@Hubjeep

4 жыл бұрын

@@Miniaturehorseexpress Interesting, is there a rebuild "kit" available?

I’m about to attempt this then I heard you say good luck Um like I don’t like the sound of that 😅

All you had to do was clean the primary!

@bswaby1

6 жыл бұрын

Wish that was the case for mine. Mine ended up breaking when it jammed in full position and I tried to pry it back.

@SilverCanary1

5 жыл бұрын

ikr! I'd at least try cleaning it and putting some grease somewhere relevant inside the casement. And the bloody imperial system! Thirteen sixteenths lmao