Great project. My Uncle built 24 tractors during the depression. Farmer's couldnt get or afford power in those days. Your vid

ei shows the dedication and intelligence of farmers. Thanks.

I have a 1971 model 4320 tractor that has a engine out of a 6600 combine installed in it. I bought it that way, would of loved to seen the transfer. It runs 140 hp on the dyno.

That’s totally worth the whole video to hear it run at the end

@andrewssoundsofthepast110

Жыл бұрын

Thanks we really like it every start is a smile

I bought a 1967 4020 myself this summer.

i plan on doing this exact project with my '70 4020 gas, wiht the engine out of a 7720 combine.. Great insight on how to start the project. once you get the cheat sheet you will have to get it to me ha

@andrewssoundsofthepast110

Жыл бұрын

Seems to me a 70 gas 4020 would be very low production numbers

just found ur content and gave you a sub. Good job keep it up

Nice job as always Andrew. Thanks for sharing

Sounds like a 7700! I think it’s the in-line pump that makes them start like that.

@andrewssoundsofthepast110

11 ай бұрын

Your correct

@trevorn9381

3 ай бұрын

@@andrewssoundsofthepast110 Yep that same engine in the 4230 with the rotary pump cranks and cranks and cranks before it starts and usually needs a shot of ether.

@andrewssoundsofthepast110

3 ай бұрын

@@trevorn9381 it all depends what pistons are in them. Have the same engine in a 4010 with a rotary and it starts right up

@wizard_of_poz4413

27 күн бұрын

​@andrewssoundsofthepast110 both the 4440 and 4240 where I work are pretty fast starting all year round

@trevorn9381

27 күн бұрын

@@wizard_of_poz4413 By the time the 40 series came out Deere had fixed the starting problems. Also, the 4240 and 4440 have the 466 engine rather than the 404 used in the 30 series tractors.

Nice. Great job

Nice 4020👍👍😀

Nice!!!

Right nice.

Sounds ,great

Some questions on the radiator fit. I'm currently fitting a 7700 Turbo engine in a early 4020 Diesel that threw a rod and wrecked 90% of the original motor. I'm at the point where I'm checking the radiator fit. The combine w/p shaft comes out right against the rad core. Did you have to shorten the shaft and water pump hub?. Also the lower radiator hose connection to modified crank pulley is very tight...hose will rub...did you have to alter the lower rad connection?

@andrewssoundsofthepast110

Жыл бұрын

On this one the water pump pulley doesn’t collide bugg t if heard of guys pushing then on but just remember your belt needs to line up with on fog the grooved. I believe the front. As the lower water pipe dad did have it moved out like a half inch. My 4010 didn’t need moved

@greatnorthernn-3154

Жыл бұрын

@@andrewssoundsofthepast110 The water pump variation I have has a longer than normal pulley hub and shaft. I'll have to shorten both by 3/4" or so. Thanks for the radiator tip...if the lower connection were tipped to the outside the hose would clear. That's a very professional job done on your tractor. The one here will end up non turbo with the fuel cut back to 90 HP or so. It's main job will be to pull a Rowse D-9 mower in the summer.

@andrewssoundsofthepast110

Жыл бұрын

@@greatnorthernn-3154 I think we used the tractor pulley but left the hun and shaft as is. If I do another as stated I. The comments I want to use a 2940 fan and try to find a cheap alternative to the M&W fan. I also have a 4010 with a non Turbo rotary pump 7700 engine it runs around 110hp and was the big tractor other then my 4040 until this build

Should be a really peppy. 4020

@andrewssoundsofthepast110

Жыл бұрын

Cooling is the only thing holding it back

What size rubber are you running on it looks great

@andrewssoundsofthepast110

Жыл бұрын

20.8-34 on the rear 10.00-16 fronts for now I’d like 11.00-16 on it

Nice job! Looks Great! What width are those rims?

@andrewssoundsofthepast110

Жыл бұрын

18 I believe

@rich2693

Жыл бұрын

Thanks. I've got a pair of 20" wide rims that I might narrow up to 18". I'm hoping to end up with a tire height on the tractor somewhere around 66".

@andrewssoundsofthepast110

Жыл бұрын

@@rich2693 not sure of your aware of rim prices but I wouldn’t cut them I’d sell and buy what you need

i don't know if you remember me or not we talk some time ago on Facebook about the M&W parts and then i gave you first chance on a john deere 1008 bush hog that need work. Any ways i have a customer that is going to be dropping off a 4020 with a bad motor and he has the motor from a 6600 that he wants me to put the 6600 motor in the 4020. What i wanna know is what did you do about the water pump fan ? and how much do you take of on the crank pulley and what ales do i need to do to make it fit. As for the bad motor me and my cousin are going to overhaul it and keep it in till we get a tractor in with a bad motor and change it out with the motor that we overhaul

@andrewssoundsofthepast110

Жыл бұрын

If you have my info pm me even your ready I’ll send you a list

@CS-zl6hc

Жыл бұрын

Ok I will pm you

@scubasteve335

10 ай бұрын

Doing a 4430 into 4010 did you machine clear though the rubber or just down to it and what about the balance holes? The manifold what deg and how much to mill off? I really appreciate any info thanks ​@@andrewssoundsofthepast110

@andrewssoundsofthepast110

10 ай бұрын

@@scubasteve335 look me up on face book and message me I’ll try to explain the best I can. Andrew Baldner

that sounds pretty sweet🎉 how much hp?

@andrewssoundsofthepast110

7 ай бұрын

We’re really not sure I’d guess 150 plus

Going to do the same thing not for pulling what u do to the front pully to make it fit

@andrewssoundsofthepast110

10 ай бұрын

Machine the front grove off set the hydraulic pump drive lug pads 7/8 inch from where the washer for holding it on sits

@user-hp3oe4xm5c

8 ай бұрын

Won’t than throw the dampener weight off , don’t want to break my crank ?

@user-hp3oe4xm5c

8 ай бұрын

A guy I know did one he lengthened the frame and all lines and fan hub and hood but dampener he left idk if I like that either?

@andrewssoundsofthepast110

8 ай бұрын

@@user-hp3oe4xm5c I’ve don’t 2 like this never a issue you could rebalance it if your worried

I just purchased a 64 4020 what's the info on the rear tires rims and Center section

@andrewssoundsofthepast110

Жыл бұрын

Not sure what your asking about the center section but the rears are 20.8-34

@djmorgan8783

Жыл бұрын

@@andrewssoundsofthepast110 tire that's on it now are 420 85 R34

@djmorgan8783

Жыл бұрын

@@andrewssoundsofthepast110 and our them Firestone Tires I just didn't know if I can get that wide of a tire on my rim

@andrewssoundsofthepast110

Жыл бұрын

@@djmorgan8783 these are pretty hard to find. I believe they are a 18 inch wide rim

FYI a 2940 fan is 7 blades and a lot cheaper then the M@W

@andrewssoundsofthepast110

Жыл бұрын

Been told that not tried one

What did you do to the throttle linkage under the dash?

@andrewssoundsofthepast110

Жыл бұрын

All factory

So would that be more like a 4430 engine with inline pump

@andrewssoundsofthepast110

Жыл бұрын

Pretty much so

@williamspates1015

Жыл бұрын

@@andrewssoundsofthepast110 my uncle did a few repower jobs years ago putting 6600 combine engines in 4010 for pulling. I did a 2640 engine into a 2520 few years ago.

@nalley6815

Жыл бұрын

It would be a 4440

@williamspates1015

Жыл бұрын

@@nalley6815 7700 still has a 404 in it. 4440 has 466 in it different engine.

What kind of horse power is it making?

@andrewssoundsofthepast110

10 ай бұрын

I’d say around 150 in the field

Im thinking about doing that to my 4010 lp

@andrewssoundsofthepast110

Жыл бұрын

Personally I’d leave it an lp but it’s your tractor

I'd subscribe, but I already did, awhile ago. Bet she'll pull good for you.

@andrewssoundsofthepast110

Жыл бұрын

Tomorrow we’ll find out

How much horsepower will you have with that 7700 motor?

@andrewssoundsofthepast110

Жыл бұрын

I’d like to farm with it around 140 to 150

@huntingandstuff9489

Жыл бұрын

@@andrewssoundsofthepast110 the normal 4020 motors were right around 100 weren't they?

@andrewssoundsofthepast110

Жыл бұрын

@@huntingandstuff9489 claimed 80

what size rear tires

@andrewssoundsofthepast110

Жыл бұрын

20.8-34

Too much mic noise

@andrewssoundsofthepast110

Жыл бұрын

I’ll try to do better with what I have