Shoutout to Aixun for sending me this Soldering Station. if you're interested in purchasing it, you can buy it here: bit.ly/aixunstore

Going from a Weller 1010na to a t12 station was a big help in learning microsoldering.. going from a t12 to this t420d with all 3 handles was game changing. If you repair electronics and want one of the best units available get this one! Worth more than what it sells for.

This is very good!!!!thank you for your sharing!!

@VCCBoardRepairs

Жыл бұрын

Thank you! Appreciate the support!

Hi, friend! under load on the T420, if the transformer makes a little noise, especially when working with the 210 handle, is this normal?

I was looking at this irons a while back. I believe to use the foam pieces you would remove the blue rubber handle part.

@VCCBoardRepairs

Жыл бұрын

Ah interesting. I'll take a look at that

For phone repair I will stick to my Aixun T3B. Impressive station. I see no use in a 245 or 115 handle in this business. I would maybe like 2 handles so I don’t have to switch tips so often. But lately my conical tip broke it’s tip about 1 mm and now it’s perfect for everything 😊

@VCCBoardRepairs

Жыл бұрын

Haha yes. I was in the same boat as you. But I think having 2x T210 handles would work great. One with knife tip & one with conical. We'll see!

@ChickenPermissionOG

Жыл бұрын

time is money friend

@limebulls

11 ай бұрын

isn't the 245 necessary for larger ICs or HDMI ports etc.?

@VCCBoardRepairs

11 ай бұрын

Nope. We do hot swap method. No issues

That’s the next thing I need is a 245 tip unit. I’ll definitely look into this one if it holds up for a couple months. Are you going to do updates on it?

@VCCBoardRepairs

Жыл бұрын

I'm going to be using it full time, so you'll see it in all my future videos.

Awesome

@VCCBoardRepairs

Жыл бұрын

Thank you

this location you are trying to put the handle is for the c115 type handle it hangs from the back i recommend to you buy it and forget the c210 you will see how much more precise will be your soldering i use 1 jbc whit 2 c115 handles and 1 aixun t3a for the c245 handle best setup possible major part of the soldering i do whit c245 and only use the c115 on the precision needed times

@arcilonjr

Жыл бұрын

and because the c115 hangs from the back you will not hit the tip on the metal holder like happens whit the c210 i lose about 3 tips in the beginning of use the c210 so i buy one jbc extension that let the same station use 2 handles both c115 and after that i buy the aixun t3a for the heavy work because it’s tips is much cheaper so my setup is perfect for our job as a mobile phone technician

@VCCBoardRepairs

Жыл бұрын

Yeah I noticed that after i recorded the video & was looking over the product page. I need to get the T115 and test it out 😅

@jaaa1976

Жыл бұрын

@@arcilonjr hi..i use JBC CD-2SE Precision Soldering station c210..but want sell and replace with Aixun Soldering Station T420D and use c115 and c245 ..is it good idea?

Can this station handle cleaning and soldering HDMI ports on consoles? Specially the mounting brackets that hold the HDMI in place on the motherboard. I can easily clean those up with my Hakko. But I would like to upgrade to something like this.

@VCCBoardRepairs

Жыл бұрын

If you get the T245 handle and large tip, I'm sure it can. Although it's not necessary. Check out my "Hot Swap Method" video.

Hi, this station can work on laptops pcb for change power jacks, etc… thanks!

@VCCBoardRepairs

Жыл бұрын

Yes it will

@reseteando1842

Жыл бұрын

@@VCCBoardRepairs Thank you for your response, have a great week.

Temperature recovery is THE difference between a hobbyist iron and a professional grade iron. The fact you can get these with that feature at that price is very impressive. The barrier to entry just got much lower. (for comparison my Weller base station without the irons is more than this set up with everything you need)

@VCCBoardRepairs

Жыл бұрын

Yeah that's crazy! I wasn't expecting much when I first texted the Aixun station but got surprised when it was actually performing well

@jstro-hobbytech

Жыл бұрын

Maybe one of yas put a word in to axiun for not honoring the warranty on the t3b. It ate every 210 I threw at it. Real jbc, their own, every other knock off and told me I didn't know what I was doing

@jstro-hobbytech

Жыл бұрын

If you guys have real repair shops why not get real stations instead of lying to yourselves. Free is great but let's not forget what it is. Even with the great ksger t12 stations are still fugazis

@ImranAli-rp4kd

Жыл бұрын

@@jstro-hobbytech I been using the t3b with t115 and t210 handle and no issues at all , I know lots of people who got it without issues so don’t know why you had issues, it’s upto everyone if they want original jbc or ones that are compatible with jbc tips, these stations are not illegal so it’s upto the individual what they want to use, I got original jbc station, 2 metcal stations , Hakko station, weller station and 4 china ones that use jbc tips, I got one that uses jbc tips which runs off powerbank aswell, all work great to be honest. What did you mean by lying to themselves ?

@jstro-hobbytech

Жыл бұрын

@Imran Ali I told them I had a defective unit ad I know a bunch of people with them. I'm bitter about how they wouldn't stand behind their product. Sorry for coming off like an ass. The first weekend I had the unit it literally blew the whole k tip off.

I've yet to get a reliable jbc clone from ali man. I'm trying one last time. My ksger stm32 t12 is finally dying after 3 years

Hi, could you answer: I just bought this T420D with T210 iron and any temp higher than 230oC like 280/300 make tips oxidized very quick, do you have same in your device?. I made calibration adjustments to be sure the temp is OK. For my older soldering stations yihua I setup around 300oC and that was ok for soldering (melting) mainboards of phones and tips wasn't became oxidized for a long time. This T420D can boil water but with such low temp (220/230oC) I can't solder much more grounded boards and when I set higher temp like 300oC the iron "I" doesn't take solder tin and I have to clean it using scalpel. The K tip died faster. I tested Ultra (high golden end of tip) tips and standard tips and ultra are better for heat transportation but same with oxidized issue. What temp do you set on your T420D ? Thanks for help. I saw in this video (@time 22:50) You setup 380oC for Knife tip, but when i set 350 the K knife burnt all tin and become useless. Maybe You used JBC tips not aixun from T420D package?

@VCCBoardRepairs

Жыл бұрын

that's weird. in the video, I used what was in the box, Aixun tips. maybe you have a defective unit. contact the seller for support

@jantestowy7884

Жыл бұрын

@@VCCBoardRepairs I will order new C210 tips for T210 iron, and I will take this standard version of tips not ultra lwhich are less expensive. Same standard versions you've got in package. Could you tell me what kind of flux do you use and tin solder wire ? is it SN60/PB40 or opposite PB60/SN40? Thanks

@tonylundberg4839

Жыл бұрын

​@@jantestowy7884Did you solve this? I have the same problem but i can use it at around 340 degrees, higher than that the tips turns black. I seem to have a hard time getting the heat to the board. Kind of useless.

@jantestowy7884

11 ай бұрын

@@tonylundberg4839 I will test iron with temp tester FG100 and i will give an info

@jantestowy7884

11 ай бұрын

@@tonylundberg4839 I will test iron with fg100 temp tester, tester will come next Wednesday

Had any problems or everythings still working good? I am thinking about picking one up 🤔

@VCCBoardRepairs

Жыл бұрын

I still use it every day

@tonylundberg4839

Жыл бұрын

@@VCCBoardRepairs Great! Have you tried any of the Aifen and Sugon stations?

@VCCBoardRepairs

Жыл бұрын

I haven't

@tonylundberg4839

Жыл бұрын

@@VCCBoardRepairs Thank you for your replies!👍

Thanks for the review! The Aixun store doesn't feature any products at the moment... Probably only due to Chinese holidays? Or the German tax system, so they do not sell directly to Germany? There are other stores that sell the station. Second question, does anyone know a similar quality station with a tweezers handpiece? 90% of my repair and restoration work is SMD caps and SMD resistors, so a single handed dual iron configuration would be very handy.

@VCCBoardRepairs

Жыл бұрын

You can buy from any reseller online, like DIYFIXTOOL.com I never tried hot tweezers but they don't seem like they'd worked well for my use case.

It does not have any hot tweezer option/support, right? :(

@VCCBoardRepairs

11 ай бұрын

Nope. I find hot tweezers to be useless

@limebulls

11 ай бұрын

@@VCCBoardRepairs that's interesting! why did you came to this conclusion? desoldering looks so easy with them and I've seen them on a lot of other KZread chanels like northridgefix. Really interested in your opinion, since you always recommend really good stuff :)

There is no comparison to the JBC station. The temperatures are accurate and doesn't drop much on small tips, which is great use in phone repairs. It is expensive as though. I paid mine for $1700., but it makes repairing jobs much easier.

@VCCBoardRepairs

Жыл бұрын

Yeah of course it won't be the same as a JBC, but seems pretty close & no complaints on the performance and quality of the Aixun.

Do real JBC handles work with the base unit?

@VCCBoardRepairs

11 ай бұрын

I don't believe so

I wish there was a way to use the jcb tweezers with this station…. God knows that massive toroidal transformer has the power to drive them.

@VCCBoardRepairs

Жыл бұрын

That would be cool. Personally I don't find hot tweezers useful though

@emmettturner9452

Жыл бұрын

Very hard to justify hot tweezers with a setup like this that makes dual-wielding the irons easy and convenient. :)

@emmettturner9452

Жыл бұрын

Just get two 115 handles and a PCB holder. :)

Sugon T3602 or Aixun T420?

@VCCBoardRepairs

Жыл бұрын

I dont know. Never used Sugon

@sameedmaqsood7051

Жыл бұрын

AiXun T420. Sugon stand is fixed with the station which is bit distraction.

Hi

@VCCBoardRepairs

Жыл бұрын

Hello ser

where are you from sir

@VCCBoardRepairs

Жыл бұрын

USA

@bintangservicecenter

Жыл бұрын

My greetings from Indonesia

if power supply become dead then both handle dead so buy 2 unit separately

@VCCBoardRepairs

Жыл бұрын

That's true

Talk about aggravating I bought this station and it only came with chisel tips, one for each handle

their store is currently saying the iron station is on sale original price is "1136" euros now for only 523 euros they are actually trying to mislead when i can find the exact iron station from somewhere else for 350 which is funny 🤣 it is the typical chinese 11.11 "sale" which is really not sale they put the price high and bring it to their real price with the "-53% discount"

@VCCBoardRepairs

Жыл бұрын

Buy from someone else then 🤷‍♂️

@thecow2756

Жыл бұрын

@@VCCBoardRepairs I am going to the comment is here so other people know to look out 😊

No it's not. I could buy a metcal for that price. They burned me on the t3b by not honoring a warranty and now you shill

AiXun = aiksun , aikseun

This is actually for the factory slaves who have to solder with both hands if they want their bowl of rice.

@VCCBoardRepairs

Жыл бұрын

Well that escalated quickly.

JBC copyright)(

@VCCBoardRepairs

Жыл бұрын

😅

@Jbkwoohooyeeha

Жыл бұрын

Yeah I’m disgusted. State of the world.