Ha! Just built my 5+ today, installed Spider, metal extruder, and Capricorn bowden before even turning it on.

@3DRundown

Жыл бұрын

Good call!

Very cool. Thanks!

@3DRundown

Жыл бұрын

🤜🏼🤛🏼

Love the recommendation. I do not need the results, but the all metal design is something I really need to squeeze more life out of my ender 3 pro.

@3DRundown

Жыл бұрын

Ender 3 pro is a great machine and this hot end should be epic on it

Very informative review! Thanks.

@3DRundown

2 ай бұрын

Welcome. I do prefer the Spider 3, and did make the switch.

@AlexanderA80

2 ай бұрын

@@3DRundown Why? I was choosing between 3 and 4(this) and after your video 4 looks prefer.

@AlexanderA80

2 ай бұрын

@@3DRundown Ok, i got it. Version 3 have more modular and serviceable design. Changed order to version 3.

@3DRundown

2 ай бұрын

4 is much closer to the current design, seen in all the modern 3D printers. However, in my experience, (and others), there have been some issues with the heating element. The Pro 3, is a TANK. It will hold up to abuse, and never let you down. It's also, yes, easy to service. The 4 will heat faster, but, who cares.

@3DRundown

2 ай бұрын

It turned out, my speedy wasn't the problem, but.... kzread.infoiXsQ5uqMCrw

Thanks for the video. I have seen some other folks having issues with theirs, thankfully I have not had problems with mine and I am loving this hot end. I was wondering what retraction settings are you using with the speedy spider?

@3DRundown

Жыл бұрын

I believe I'm at 5/30, or super close to that. I will check when I'm in. Away till Tuesday.

Does the fan duct fit properly after swap to this extruder? I have impression the nozzle is a bit lower and air blows on it, not on the filament.Greate movie by the way.💪💪💪

@3DRundown

Жыл бұрын

This thing is really small. It's virtually the same size as the stock hot end. Looks fine to me. My prints have been super

I sometimes use my teeth to strip the wire back. Can't be arsed looking through my tool set for wire cutter.. 😅😂

@3DRundown

6 ай бұрын

As a fisherman, like my dad before me... Our teeth are tools. 😂😂

PID tuning on my ender 3 results in thermal runaway but if i just tell it to heat to 200 or 220 for that matter it will reach tempature and stabilize without thermal runaway. Is this a firmware bug? The tuning seems decent enough already right off the bat because the tempature stays within a degree or so. What are your thoughts? One thing i noticed too is that with my hotend once i tell it to heat up it will reach around 120 degrees in only about 5 seconds, in crealitys video showcasing the heatup time they too have their hotend heat to 120 degrees instantly and then they have a steady rise. With yours there seems to be no spike in tempature and just a steady increase the whole way through.

@3DRundown

Жыл бұрын

I would avoid Creality Firmware as much as possible and go with something like MRISCOC. Also, I wouldn't lose sleep over PID tuning. However It shouldn't be failing like that.

Excellent video my friend can I ask which firmware are you running I'm looking at changing from stock thanks

@3DRundown

Жыл бұрын

Thanks so much. I'm using TM3D, it's a massive improvement, and the install is not terribly complex. Take your time and do the Screen 1st!. #SuperThanks

@markingram268

Жыл бұрын

Thanks for getting back to me which motherboard do you run

Thanks for the video, will this kit fit the ender 3 v3 ke without mods or should i look for something else?

@3DRundown

2 ай бұрын

No. Totally different.

Awesome video, thanks. I have an Ender 5 plus, and Im deftly will add the new hot-end!!! Question: your Ender 5 plus firmware seems more complete and better than mine, what is your firmware version? mine is 1.70.2 and it sucks! Thanks

@3DRundown

11 ай бұрын

Brother, forget the firmware. Put a Sonic Pad on it. 15 Min setup and off you go. However, the firmware that WAS on it (just a static screen now) was TH3D, and it's worlds better than stock. Now it has Klipper flashed to it, via the Sonic Pad, but the screen stays like that, as it's no longer used. Sonic Pad becomes your screen

@3DRundown

11 ай бұрын

Check todays VLOG short

@ReviewRapido

11 ай бұрын

@@3DRundown Dang, I was thinking about that, im between a Kliper or an RPi3b+ or the sonic pad!

@3DRundown

11 ай бұрын

Sonic Pad, unless you are REALLY STRONG with your Klipper skills

Nozzel came off and tightened with no issue. Where did you end up with your reaction setting with this HE on your E5+? I figured that it would be the same as my Microswiss but definitely not.

@3DRundown

Жыл бұрын

6.5 / 25

I just got mine today, and when leveling with the creality bl touch, I noticesd that it sits lower than the level and I can't level that bed at all with out the bed pushing up on the hotend.

@3DRundown

Жыл бұрын

You will want to use a spacer. kzread.info/dash/bejne/mJyIq8iIYdDFqbQ.html

Hey, nice video! I recently upgraded my E5+ to this hotend. As you said it comes with a .4 and a .8 nozzle. Have you changed the nozzle after use? I am going to put a .6 on but am not sure where or if I need to hold with pliers while changing. With my other all metal ends I need to hold the block in place so it doesn't spin. Any tips?

@3DRundown

Жыл бұрын

I have not! But there is not heat block, so, should be good to go on the Nozzle

@nachodaddy6572

Жыл бұрын

@@3DRundown Nozzel came off and tightened with no issue. Where did you end up with your reaction setting with this HE on your E5+? I figured that it would be the same as my Microswiss but definitely not.

@3DRundown

Жыл бұрын

6.5 / 25

iv installed the speedy spider, i cant dial in my retractions whatsoever! i used to have great prints, is there a trick to these all metal hotends or do i have a faulty one!!! thank you sir!!! used to run 6 60mm speed, now it looks the best, which is super stringy at 2 and 30mm!!!! i dont want to give up on this ender since i had it from the start of this hobby!!!

@3DRundown

Ай бұрын

2 is not enough for a boden setup. Start at like 6/25

I am just a little confused is it plug and play or do I need to splice the wires on an ender 5 plus?? I thought i heard you say you can just plug it in and you're done.

@3DRundown

4 ай бұрын

Yes. Many models will connect directly too the included harness. At launch, this information can often be hard to confirm, or, straight up wrong. So, I try to cover the bases for self splicing.

I just got mine - not sure how this will mount on a CR-10v3 that has the direct dive extruder... any ideas? Thank you!

@3DRundown

Жыл бұрын

I ditched the Titan and went Bowden/Extruder. My CR-10 works so much better that way. Not sure on using it with the Titan...

Do you have any issues printing with PLA on the spider all metal hotend. I installed a Micrswiss all metal hotend and direct drive and every time I try printing with PLA it cloggs the hotend. So I only use PETG now which I have had no issues with.

@3DRundown

Жыл бұрын

I print exclusivly with PLA. However. I am going to swap my Speedy for a Spider 3. I prefer that one.

Is the size of the speedy hot end the same as the stock hotend of an ender 5 plus? I have the og spider hot end and it's way bigger than the stock so my bL touch doesn't reach the bed before the nozzle and my nozzle is crashing into the bed. Not sure how to correct this. I tried adjust the bL touch with a bracket but then the bL touch crashes on the support brackets to the left when bed leveling 😮‍💨

@3DRundown

Жыл бұрын

A spacer will fix your problem. I have a video on that. However, ditch that slider and get a spider 3 (not the speedy. It fits, but I have had problems). SPIDER 3 is normal size, and will work with no modification.

I’ve installed mine but after having near perfect prints on my stalk hotend this one I havnt gotten a single print nor does it adhere to my pei bedsheet

@3DRundown

Жыл бұрын

First layer issues are generally a Z-Offset issue. Did you adjust your Z during the 1st layer to set it correctly?

Hiya Greg, this should be compatible as well with a V2 Neo, right? thx

@3DRundown

11 ай бұрын

The hot end cover is weird on the neo. May need to tinker it a bit, but yea, it should!

What firmware are you using on your ender 5+? Do you have an installation guide by chance?

@3DRundown

5 ай бұрын

Sonic Pad. It's an easy setup, and the printer is instantly like a new machine. It's NIGHT AND DAY. Sonic Pad, is the way, PERIOD. Grab a used one or on sale. You'll be up and running in 30 min, and after a short learning period, you'll wonder HTF you lived without it.

@kriid3107

5 ай бұрын

@@3DRundown awesome thanks, just picked one up it should arrive in a week or so I’ll let you know how it goes 😁

@3DRundown

5 ай бұрын

Awesome. I put it off for MONTHS, cause I didn't believe in it. Boy was I so wrong. You'll love it on your 5+. Just be patient as you learn the ropes. And remember the new GCODE for ABL! G28 ;Home BED_MESH_PROFILE LOAD=default

@kriid3107

5 ай бұрын

@@3DRundown hey i just got it today, what exactly does this gcode do and how do i put it into my Creality slicer

is it 12V or 24v? I have a trusty CR10 and I would like to install it on.

@3DRundown

Жыл бұрын

Spider is CR10 compatible. 👍🏼

How is it printing 1 month later?

@3DRundown

Жыл бұрын

So far, Zero issues. I don't use it a TON, but haven't had any problems. I DO use the Spider 3 a ton, and it's my favorite hot end so far. Clean prints, every time. Not a single clog yet

Just installed Spider Speedy on my ender 5 plus Stock setup I plugged the extension cable between the thermostat to the backside of the printer “without soldering”. Plugged the heater with the extension till the backside then soldered it. I’m using Marlin FW It is working great so far With the old stock hotend I was suffering from temp runaway and clogging and fluctuations of temperature Now I’m looking for the best way to update the firmware to 300 degrees Any advice?

@3DRundown

Жыл бұрын

Look into TH3D firmware or Gift her a Sonic Pad.

@Hamed245

Жыл бұрын

@@3DRundown appreciate you advice

could you put this in the sprite extruder? like ok the s1 or s1 pro thanks s

@3DRundown

Жыл бұрын

No. This is for Bowden setups. You can get the High Flow Kit, or the new Ceramic hot end

@3DRundown I have the spider 3 pro hotend now for around 4 months. And till now it worded will but for 1 or 2 weeks now I can not finish any print anymore - it starts clogging ….. any methods works for 1 or 2 prints maybe. What is your experience with the speedy spider after 4 months?

@3DRundown

11 ай бұрын

No clogs yet on my Ender 3 Max with Spider 3. I print on it almost every single day. Have your Slicer settings changed? Could be retraction settings? But I'd start by looking at your Bowden tube to see if it's scorched or deformed, and, consider a new nozzle

@ziruszirus1654

11 ай бұрын

@@3DRundown thank you so much. I will check.

Know the wattage of the heater? I’m running the Mriscoc FW, and it uses MPC, and while it claims to complete the auto tune, it sets everything to 0.000 and that prevents the hot end from working. I tried adjusting wattage up, that seems to help the auto tune curve… Maybe. Still haven’t gotten a completed run that actually gave settings. Either way, I found some settings for a 65w hot end, that may work well enough to at least get working for now.

@3DRundown

Жыл бұрын

Hi. I'm note sure. I'm running TH3D on my 5+. It worked straight away. I'm gonna try it on a 3 Max or 6 Max, shortly.

@3DRundown

Жыл бұрын

Go to Creality.com and do a live chat after 9pm. See if they know

What will this do for my Ender 3 pro, besides faster heat up times? Great t Greg keep on keeping on🔥👍🤓

@3DRundown

11 ай бұрын

I wouldn't do it. These ceramic hot ends are the future, but I had problems with 2. Go for a Spider 3. Really excellent hot end. However, your stock hot end is OK also. Eventually it will wear down, get gunky, and become a problem. Spider 3 is the way to go

@williamwiese9963

11 ай бұрын

Thank you Greg!! What about now? You think there's been enough time for them to work the bugs out?. ✌️

@3DRundown

10 ай бұрын

I want to think so, but, I have no way to confirm. I know they have already revised the K1 Ceramic heater.

Hi there! Thanks for the video! Iam installing the spider speedy now on my Ender 3 max neo. But how do you know witch orange wire for the heating element is positive and negative? Or doesn't that matter?

@3DRundown

10 ай бұрын

No polarity

@airdevil21

10 ай бұрын

@@3DRundown oke thank you!

@airdevil21

10 ай бұрын

@@3DRundown it doesn't fit is 4mm shorter than the original hotend so have to find a mounting plate first.

@3DRundown

10 ай бұрын

Sorry, I reply to this while super distracted. YES, the NEO, sadly, has an odd hot end cover

@airdevil21

10 ай бұрын

@@3DRundown yes when I mounted the spider speedy the nozzle is unable to touch the bed the autolevel sensor will hit the bed first. And I learned that it's really important that the tube is tight against the nozzle.....still learning :)

I'm confused about the design of this hotend. Does the heatsink really touch the ceramic heater or does it only look that way?

@3DRundown

Жыл бұрын

It's a ceramic tube, below the Heatsink, with the heat-break inside

@Noxoreos

Жыл бұрын

@@3DRundown That's what is confusing me. The ceramic heating element has cooling fins around it in the lower portion. If those fins touch the heater it would actually be cooling the heater and be pretty bad for performance. That's why I'm wondering if they touch or not.

Silent motherboard (stepper drivers) would't be the worst idea,

@3DRundown

10 ай бұрын

My 5 sings like a bird, but works so well, I don't touch her

would u mind sending me the firmware you are running on this ender 5 plus. please and thank you

@3DRundown

4 ай бұрын

Hi Friend. I'm running SONIC PAD on the 5+. You should too. It's a quick and easy setup. It will bring your 5+ up to modern standards. Klipper has a small learning curve, but, if you don't go crazy trying to push the machine super fast, and all that, it's easy, and you shouldn't fear it at all. I 1000% suggest you go SONIC PAD on the 5+. Otherwise, use TH3D. But.... Go Sonic Pad. Used on Ebay will do.

Would you recommend this over the Spider 3.0?

@3DRundown

Жыл бұрын

I'm having a tough time with that call. I really like the Spider 3, and I like that the heat Block and Coupler can be easily replaced, but, if this thing holds up, it's 1000% the future of Bowden Hotends. Till some time passes, it's a tossup, but I see no reason NOT to get one, yet....

@noviceartisan

Жыл бұрын

@@3DRundown Nah, coupler looks like it can be easily replaced, but it can't lol I'd say try it, but you'll break the unit in trying, I did xD

Can you do a firmware update or upgrade for the ender 5 plus? I put insanity firmware, then tried going back to stock. All I get is either Chinese and buttons don't work. Or English and buttons don't work.

@3DRundown

10 ай бұрын

Creality firmware is awful, and the most recent version has a language but. You'd want to go back one, but, I wouldn't even do that. Put a Sonic Pad on it. It's an easy setup, and works great. It's like going from a Potato, to a super computer

@smallnuts2

10 ай бұрын

@@3DRundown thank you

I do appreciate your videos (Thumbs up) but you would get longer watch times and more views if you also included some results segments in these videos. I know that the videos would take longer, but I think the lifetime of the videos would be worth it.

@3DRundown

Жыл бұрын

With 3 Partnered YT Channels, over 2000 videos, millions of views, and endless analytics available on YT, I promise, even if Jesus Made an appearance, I wouldn't get longer retention. I'd be talking to myself by the end. People like shorter, focused content. Drop off is 80ish% in the first minutes of any YT video. Plus, results are the result of a landslide of factors. That said, I share my printing and work, multiple times a day on my Insta and other YT. @GreggAdventure. ✌🏼

Have I helped you? Help ME continue this channel with some support: Click the "💗THANKS" button, to Send a Tip. Or: paypal.me/cerenzio & venmo.com/gregg-cerenzio Support me via www.patreon.com/3DRUNDOWN Use my Amazon Affiliate Link when shopping: Amazon: amzn.to/2miGQq9

Giving up on this extruder... went through 2 already... clogs VERY easily. Clogging was the reason I ditched the stock hotend... The nozzle does heat up really quickl;y and the nipple guard is great. Other than that, not that special. Still looking for a good replacement for the stock hotend. Any recommendations would be welcome.

@3DRundown

Жыл бұрын

My Spider 3 have never clogged. I use it every day. However, your Speedy shouldn't be clogging either. But I am having heating issues with it. Not yet sure if the hot itself, or a wiring thing. Maybe your retractions too high? Should be 5ish. Spider 3 is Super. I may put one on my 5+.

@TheBrazilWill

Жыл бұрын

@@3DRundown this is precisely what I was thinking. Retraction or heat creep. I’ve avoided doing a Hero Me because I wanted to keep the printer as stock as possible as long as have the stock gantry. I was going to return this second heated today but I may try to pull it apart and fix it just to test before I get another.

@3DRundown

Жыл бұрын

I replaced my Speedy on the 5+ with another Speedy.... still troubles. I replaced it with a Spider 3, and so far it's super.

@TheBrazilWill

Жыл бұрын

@@3DRundown they refunded me my money and asked me to keep it longer so I am installing a Hero Me on it to see if it makes it better.

@TheBrazilWill

Жыл бұрын

BTW that hotend is crap, I went back to the stock one. LOL

Hi so I have a ender 5 plus and Im fairly new at wiring, do I need to do the crimping and wiring he does between the hot end and the existing wiring? or was that to just show how to do for those who wanted the option? If I do need to do it, does someone mind explaining what all the different wires do?

@3DRundown

10 ай бұрын

Consider going with the Spider 3. The wires just clip on!

@3DRundown

10 ай бұрын

For the Speedy Spider, the wires are pre-installed and very short. You just crimp the 2 red wires for the heater. The 2 white's are the Thermistor. Nothing else needs to be touched.

@jeremiahguadez2090

10 ай бұрын

thank you so much!@@3DRundown

@airdevil21

10 ай бұрын

​@@3DRundownso for the heater + and - doesn't matter? For the thermistor it doesn't I read that.

@3DRundown

10 ай бұрын

neither have polarity

It looks good and I only have one concern. It looks like the heater cartridge and thermister are not replaceable. It looks like you would have to buy a new hotend if you damaged one of the wires somehow.

@3DRundown

7 ай бұрын

Correct

@zk_6312

7 ай бұрын

@@3DRundown Okay, thanks. I will not be buying this one then. Maybe version 3.

@3DRundown

6 ай бұрын

Spider 3 is my favorite hot end.

@zk_6312

6 ай бұрын

@@3DRundown Yes, I have been looking at that one as well as the Phaetus BM.

why not use a lighter? is this some weird don't touch it with an open flame stuff?

@3DRundown

Жыл бұрын

Because I have a fancy expensive tool. Might as well use it. 😛😛 Plus I can control exactly where the heat contacts, and the exact temp. It produces superior work. Also, my butane lighter ran out my on my very first take. 🤣😂🤣

i would solder instead of the crimping but an excellent descripten of the mod greetz from austria

@3DRundown

Жыл бұрын

Agree. I try to show methods that the average person can do, as well as what instructions show, if there are any... Solder would totally be a better choice. Greetings from NJ USA

@unclenicnac1035

Жыл бұрын

@@3DRundown btw i ordered the hotend afther this video^^ you should make affilated links for european countries too 🙃🤣

@petercallison5765

Жыл бұрын

You cannot solder thermistor wires as it changes the resistance.

@petercallison5765

Жыл бұрын

@@3DRundown You cannot solder thermistor wires as it changes the resistance

@unclenicnac1035

Жыл бұрын

@@petercallison5765 and a crimped cable has no change in the resistance... basically crimped cabels have a higher inner resistance then soldered ones. keyword contact resistance... but you should know how to solder. 95%+ do not know how to do it.

I'm experiencing heat creep with the Spider Speedy on my Ender 3. I don't know what's causing it.

@3DRundown

Жыл бұрын

Just finished a long print for an Uber Jason X Machet, and it went perfect. Haven't used it a TON yet, but, so far so good. I'm doing an E3 MAX next. What's your symptoms?

@andrelloydtorres4468

Жыл бұрын

@@3DRundown I had mine replaced twice. This is my third spider speedy and still having heat creep. What I did to solve the heat creep issue, is to use Thermal Grizzly Kryonaut for the heat break, heat sink, and the ceramic heater block.

How does it wire into an older v1 cr10?

@3DRundown

Жыл бұрын

You would splice it to the existing wires.

@jackwood6214

Жыл бұрын

@@3DRundown okay thank you! I need to check for positive and negative for either the heating element and thermistor? Or does it not matter?

@jackwood6214

Жыл бұрын

@3DRundown got mine installed and won't heat above 160c. My printer is a cr10 12v. Are these for 24v printers?

Does Polarity matter on either cable?

@3DRundown

Жыл бұрын

No

@airdevil21

10 ай бұрын

​@@3DRundownthanks! Was searching for this answer as this is my first hotend upgrade I do.

You didnt mention anything about thermistor settings? I installed this on my klipper build and I am having my printer disconnect over and over ever since installing it. I think it is because of my thermistor....

@3DRundown

Жыл бұрын

I am running TH3D Firmware on my 5+ and made no changes at all. It's been amazing. There may be changes you need to make on Klipper. I'd have to study up on that one. Feel free to pop into my Sonic Pad group and chat with the peeps there. facebook.com/groups/crealitysonicpad

@ThePrintHouse

Жыл бұрын

@@3DRundown Thats very suspicious. I trust that you are printing just fine, but I have serious doubts that your nozzle is actually the reported temperature you think it is. Today I am going to set my thermistor back to the stock settings and see what happens. Thanks for the input.

@3DRundown

Жыл бұрын

Check out my short on the Uber Jason Machete Parts. That was literally my first print after the Test dog. Flawless

@expertshooter2055

Жыл бұрын

​@@ThePrintHouse this seems to be a common problem with the hotend that I, and many others are experiencing. If I set my print settings to 260c I can get good quality prints, where if the nozzle was actually 260 degrees the print would look terrible. Something must be going wrong on crealitys end.

@ThePrintHouse

Жыл бұрын

@@expertshooter2055 Well every thermistor is using different resistors in order to produce the readings it does, so every resistor is calibrated differently. That is why you need to change the firmware to recognize a different thermistor or else the temperature your 3d printer believes it is is incorrect. In Klipper that is easy to change, not so much with stock marlin printers without custom marlin compiled firmware. Because this hotend can reach higher temperatures than the stock hot end, they were required to use a different thermistor than the stock hotend and so anyone installing this on a typical machine without klipper will likely need to custom compile their firmware to get accurate readings.

I have a problem with setting the temperature. PID doesn't help It does not heat the nozzle during printing. Still missing 10*C The standard HOTEND works without any problems. Spider 4.0 works beautifully except for this E1 temperature error

@3DRundown

8 ай бұрын

E1 typically means the Thermistor has a problem, or isn't connected. If your get an "not heating as expected" error, try this: Turn your fan down to 90% when slicing. And test again. Mine failed EVERY PRINT, till I made that change. Zero fails since.

@Robert_Monitoruj24

8 ай бұрын

My fan is 0% I have PID but there are still a few steps missing

@3DRundown

8 ай бұрын

Why is your fan on 0%? Should be %100, however I found I got the error, unless I used 90%. I'm talking about slicing for PRINTING (FYI, I switched to Spider 3)

@3DRundown

8 ай бұрын

You are on Sonic Pad?

@Robert_Monitoruj24

8 ай бұрын

No TFT35 E3 v2 and SKR mini v2@@3DRundown

what firmware you running on your 5 plus?

@3DRundown

6 ай бұрын

Sonic Pad. Best move ever. So easy.

@derekgreig6905

6 ай бұрын

@@3DRundown I just had a look at them. Doesnt say compatable with the 5+ tho

@3DRundown

6 ай бұрын

I'm Running Sonic Pad on my 5+. It hasn't missed a beat since the day I turned it on. Setup was like 10 min, and at the time, I had never used Klipper before. I assure you, 5+ works on Sonic Pad.

Oddly they claim 250mm/s for Spider 2 300mm/s Speedy and surprisingly 400mm/s for Spider 3.0. - faster than the speedy!!!!

@3DRundown

Жыл бұрын

The V3 is a really great hot end. I think their best. Will see how the Speedy holds up. Having no Heat Block is kinda cool. But the "Speedy" refers to the Ceramic Heater, giving it a fast heatup. I don't believe Speedy has a HF Nozzle on it. I think it's an MK8. Spider 3 Does.

I had a lot of issues with inaccurate temperature readings. I ended up sending it back. Did you have any of the same issues?

@3DRundown

Жыл бұрын

Mine has been fine. How did you determine it was inaccurate, and what negative effect did it cause you?

@scottschnatzmeyer85

Жыл бұрын

I am having the exact same issues. I am running a BTT SKR 3 along with upgraded firmware. No matter what adjustments I make on this damn thing, it reaching about 10* below the requested temp and then fails. It is really becoming a pain right now.

@ericnfla

Жыл бұрын

@@3DRundown set it at 200° and it still can't melt PLA have to set it at 220. Then while printing temperature fluctuates wildly. Thought it was because I had the CR touch inside the fan shroud so remove that and was still doing the same thing although not as bad.

@adobolifts637

Жыл бұрын

@@ericnfla it is recommended to PID tune the hotend after changing it

@expertshooter2055

Жыл бұрын

This seems to be a common problem with the hotend as I have seen multiple issues with this issue. I am having the same problem and I'm thinking of just returning this thing and buying the spider v3.

That was pointless. Your supposed to print at 400mm. 😅😅😅😅 let's see how fast it can print?

@3DRundown

Жыл бұрын

I give Zero F*cks about speed. Go ahead and print us something at 400. Link me to the video when your done

So I got this hotend. I can’t get it past 7.2 mms cube flow rate. If I increase the temp to 280 it works but then I can’t really print with it since everything just droops and looks fucked. Wtf am I doing wrong? With a stock kobra go hotend I can push 17 mms cube. This spider was literally almost the same cost as a brand new kobra go