This video has it all. Thank you so much. One way to get the feeder tube out without buying the special tool is once the feeder tube bolt is removed you can lightly reattach the fuel line onto the tube and it’ll give you more leverage to pop it out

I could watch this all day. I have a 6.7 Cummins and I love watching maintenance videos. How in the hell would you ever remove the injector / tube in cylinder 6?

@youjizz1991

3 жыл бұрын

Im guessing cab off

@randomrandywv1381

3 жыл бұрын

Struggle a bit more. Just did it on mine. Offset wrench (3/4” or 19mm) is necessary. Torquing things is a bit more difficult due to space constraints

I read that you should always replace the injector tubes when swapping injectors. The tip of the tube forms its own seat on the opening to each particular injector.If you re-use it on the new injector, you run the risk of leaks.

Thank you that helped

It's mind-boggling the amount of work to change an injector you would think somehow they would have the injectors on the outside if possible because I don't even comprehend wiring being on the inside of the cylinder head without just melting totally

Relly good video

THANKS YOUR VIDEO HELPED ME TOO MUCH I’m in Dallas Texas and I work on construction if you need any help just let me know I love to do all Maintenence on my trucks and I just got my first diesel truck it’s a 2019 2500 ram Laramie and is really hard to find any help with this new truck

Thank you for the video. I'm about to replace all 6 of these plus the pump on my 2020.

@totalarchertx11

Жыл бұрын

Did you change them yet? I’m on the verge of swapping to 60% overs but nervous of the difficulty lol

@kingpeasant5099

Жыл бұрын

@@totalarchertx11 I did. It wasn't the easiest job I've done but it was pretty straight forward, overall.

Awesome video!!! What software are you using for the scan tool/computer?

How would you change injector 5 and 6

So I took the exhaust side push rod out to clean it cuz some debris got on it well when I went back to put it back on it sits higher than the rest if I tight the Allen bolt it wants to bend what can I do to fix it?

Can you get the injectors code without getting the I ejectors out? I replaced a new engine and need to do the IQA program for the injectors

hello, on 2016 ram 2500 do I need to type in the code for the injector or is it only on the fifth chance?

Hola cambie un inyector en mi ram que estaba malo 2500 2012 6.7 Cummins y le coloque otro nuevo y sigue funcionando en 5 cilindros el motor o habra que codificar el inyector?

After done do you need a pc to reset the injectors values?

Its actually cheaper to replace all 6 injectors on the 2019+ Cummins 6.7's. 1 injector by itself runs around $1800. A 6 pack of injectors runs $2700.

Would like to see how you tackle replacing #5 or #6.

@youjizz1991

3 жыл бұрын

I was asking myself the same question…cab lift maybe?

@justinp6383

2 жыл бұрын

@@youjizz1991 not needed, you can get to them with no issue its just more of a pain

Great video thx ? What makes an injector go bad is it bad fuel

@TDRAuto

3 жыл бұрын

Contamination is a big one, I had one where the pick up pump failed and sent metal debris through the filters to the high pressure pump and clogged up the injectors.

Did you have to rotate the engine at all?

I don't see a final torque number on the injector hold down, you went straight to the rocker replacement after the the connector tube torque. 8 NM seems awfully light when every other 6.7 before it is recommended at 79" lbs.

can I reset/reprogram my injectors on a snap on scan tool? just got my injectors Flow tested and cleaned and need to reinstall.... Thanks!!!

@TDRAuto

3 жыл бұрын

Sure, as long as that function (offset reset) is supported by the scan tool.

So the rocker arms/valves/bridges don’t need to be timed/gabbed anymore on the 2020s?

@TDRAuto

3 жыл бұрын

There are no adjusting nuts anymore, it’s all hydraulic now. If for some reason removed there is that timed multistep tightening procedure to allow for proper oil bleeding of the hydraulic lifters.

I just had my engine replaced, wanted to do the IQA program for the injectors, got the I ejectors out and non of them have codes 😭 What should I do??

@TDRAuto

6 ай бұрын

Sorry for the late reply, Cummins 6.7L injectors don't need to be programmed, you only need to reset the injector values.

2018 also need to be reprogrammed?

@gb4807

2 жыл бұрын

yes

Just replaced all six high output injectors in my 2019 Ram 3500. Now she won’t crank. Any suggestions from anyone?

@penguinsgarage

6 ай бұрын

You locked it up with something

2020 and already needs an new injector?

@TDRAuto

3 жыл бұрын

I haven't done another one since, I believe it was a rare occasion!

@nicknetefor7116

3 жыл бұрын

He said he thought someone was in there already because a couple bolts were too tight