5:24 Brasso is safe to use on the silver you would find in your waterloop, but is not recommended for aesthetic pieces as it might cause micro-scratching. Use a less abrasive polish like Silvo for delicates such as jewelry or silverware. 5:36 We misspoke during one of the sponsor talking points and incorrectly said “IP7X” (rating of dust resistance) instead of the correct “IPX7” (rating of water resistance).

@Treetrytrey

Ай бұрын

W water resistant

@SoundsLegit71

Ай бұрын

I think the water cooling computer industry could learn a couple of things from a vehicle cooling systems. For example, the radiator hoses on a vehicle are actually conductive. Yes, the rubber is impregnated with carbon or bits of metal. This is extremely important. Otherwise, a corrosive reaction will happen between the engine block and the radiator, kind of like a battery. Also, has anyone tried putting like 10% antifreeze in the system?

@iamdmc

Ай бұрын

that garbage ek foam also dissolved on me don't feel bad... everybody buys ek once

@circuit2006

Ай бұрын

I believe the first note is more so just letting people know if they decide to do this for personal use, and the second one was the only actual correction. Although they still should've edited it in instead, or just re-do the sponsor segment because those would be very easy compared to the video it's self.

@octorokpie

Ай бұрын

@@pixelpirte15The Brasso point isn't really a correction, just another helpful tip- they didn't say anything about jewelry in the video about water cooling. Toothbrush companies have ad money to spend, may as well take it. What planet (or economy) are you on? The one where people only advertise things you like?

"The thing that attracted me to custom water-cooling was the inconvenience of it, I love taking apart my computer and washing parts of it like dishes in a sink, also the thrill of losing all my expensive components to water damage gets my heart racing like nothing else" - Custom water cooling fans apparently

@choochooChuy

Ай бұрын

whoever is running this channel definitely wants this to happen

@GrimReaping

Ай бұрын

Some people want to drive a prius the speed limit til the wheels fall off, some people want to tinker on a turbocharged hotrod every weekend that might tear its own wheels off. To each their own i suppose.

@basshead.

Ай бұрын

@@GrimReaping what about an air cooled 993 turbo s?

@Ryzza5

Ай бұрын

You must be young 😂

@woe2you2

Ай бұрын

If you do it right you won't have any of the problems in this video. Also unwise to do the things in this vid that will CAUSE problems: don't put acid in your rads unless you're prepared to test the pH before hooking them back up to a loop. Ignore the iodine as biocide as well: use a reliable premixed coolant like DP Ultra, Koolance 702 or Mayhems X1 and you'll have biocide and corrosion inhibitor included.

air cooling maintenance: "is it spinning?"

@Basil_left

Ай бұрын

No, it's breakdancing

@semi.

Ай бұрын

Is it dusty?

@Dasgabar

Ай бұрын

@@Basil_leftNah dude, it‘s solving the Birch and Swinnerton-Dyer conjecture.

@Legendendear

Ай бұрын

Disassembly, repaste, reassembly. Done.

@choochooChuy

Ай бұрын

@@Basil_left maybe it knows what its doing

Have always thought, "Yeah, I really just don't need *THAT* in my life" whenever thinking about watercooling and boy, was this video a good reminder!

@exander77

Ай бұрын

This. I like AIO 360 GPUs, because of low noise, but otherwise, fuck that.

@MaunoMato99

Ай бұрын

Yeah a loop doesn't look like that unless you fill it with crap coolant ( which they probably did in this case ) or if you never drain it, which takes like 5-10 minutes and another 5 minutes to fill it. Obviously staged for this purpose but yeah, you believe what you believe. Watercooling is very cool and fun to work with, it's never necessary though, unless you have the latest Intel high end CPU I guess. But just like a car with tons of moving parts, it requires some maintenance.

@BigPanda096

Ай бұрын

This isn't how it goes unless you put literal mineral water with bacteria in it in the system. You use proper coolant mixtures with fresh distilled water, and this NEVER happens. Especially if you drain it once a year and refill it. Which takes 5 minutes and no cleaning required. The coolant mixtures have cleaning detergents, seal conditioners and lubricity agents to prevent wear and tear. Get a decent mixture, since I live in Florida I use 30/70 coolant/water mixtures since 30% coolant is the optimal ratio for perfect dispersion and suspension of the coolant detergent and additives, without causing a change in viscosity and reducing waters heating coefficient. The inherent issue with air cooling is that there will always be one side cooler and one side hotter. This molecular difference causes the metal to bend and distort. No matter what you choose you will have maintenance. With air coolers that maintenance is removal of the cooling block to clean the fins, checking and straightening any bent fins from the process, then carefully reseating it. When the cooler block begins to warp, you need to get a new one. Anything but the Noctua cooling blocks usually warp in a year. Noctua 3 years roughly. But they all warp even Noctua. For liquid cooling if you properly build the set up or even just use an AIO, that process is, drain fluid from storage tank and cooling block, using fresh distilled water refill it and run a short cycle (only if you REALLY are scared it's not clean inside already from improper mixture use in the past, but if using proper mixture this is not always nessisity especially if using the se mix in brand and quantity) then drain it again, and then refill with your proper solution. This process takes anywhere from 5 to 15 mins. The air cooler can take a few hours depending on the size of the block and the damage to the fins during removal and cleaning. What they did here in this video is what using mineral tap water does to your system. Use fresh distilled water with the mix to make your solutions you put in the tank. I've done this for 8 years and I've never had to do what these guys have and I've been maintaining my customers PCs that I built for anywhere from 1 to 8 years depending on customer. This doesn't really happen in proper builds.

@bp3d106

19 күн бұрын

I love my custom water cooled computer. It was fun to build, looks cool, and it's quiet as the fans barely run. As a result of the low fan use, it stays clean as it's not pulling in dust. I use all Corsair products and although they say to change out the coolant every year, I waited two before doing it last time.

@saitodosan9377

5 күн бұрын

@@bp3d106 Yeah I just use an AIO cooler (Kraken whatever a while ago, Cooler Master ML240 now) and I've never had to do ANYTHING over the like 7 year total I've had them. I used the Kraken whatever-it-was for 5 years before switching, and I only did so because I was essentially building a whole new PC minus the graphics card and I wanted to go for a mostly white build. Never drained the liquid or did anything special to clean it, just dusted it like I do with every other part. Never had any issues. Very quiet and the temps are perfect!

I normally get annoyed with sponsored videos but this was pretty entertaining! I like how the main focus was on the PC instead of the toothbrudh for 20 minutes straight.

The toothbrush sponsorship was... inspired.

@whitepaws60

Ай бұрын

Inspired by their time's meeting fans at LTX lol

@ledocteurgonzo

Ай бұрын

yeah it's just a looong ad for the TB :D

@baths4carsraspberrypicomputer

Ай бұрын

tOoThBrUsH

@Metal_Maxine

Ай бұрын

WAN show said they wanted to do a water-cooling cleaning episode for ages, they just didn't have an angle to stop it being boring... clearly, vibrating toothbrushes are that angle

@Doroga05

Ай бұрын

Yeah... 16° holy moly with an accuracy of 0.1°. can someone remind me how this one is better than the one just vibrates?

I had the same EK coolant in the loop for 6 years, occasional topping up. Almost no residue, no leaks, tube still flexible, and the system was used daily. Rebuilt and cleaned it a month ago now.

@thatsl1ve183

Ай бұрын

Ek coolant is just not reliable. In some loops it works, in others it fails pretty fast. DP Ultra just works and costs the same.

@naibaf710

Ай бұрын

@@thatsl1ve183 Yeah not sure, always worked for me.

@TheElfangor

Ай бұрын

@@thatsl1ve183 Always depends on materials used in the loop. I use DP Ultra too, after almost 2 years still no sign of any residue or whatever in my clear coolers or the reservoir. Before that I had Innovatek Protect, which after about 3 years did clog up my CPU block which was my reason to clean and rebuild the loop.

@Yorhosashi

24 күн бұрын

@@thatsl1ve183 just dont mix different alloys in your loop! my loop contains only of copper alloys. and i clear my loops every 1 to 2.5 years. until now i still have a crystal clear loop since 2013

@user-re7wo2zs7s

12 күн бұрын

@@thatsl1ve183anecdotal but my same EK loop lasted for a decade. Also there was a 4-5 year period where I didn’t drain the loop either.

This video is 100% a fantastic demonstration why I always air cool my systems. Thanks for the validation.

@rata536

Ай бұрын

Air cooler and a kryosheet. Just pull out the fan and blow the cooler without ever dismounting it.

@garydunken7934

24 күн бұрын

Me too. Never bothered with water cooling even when I overclocked the system.

This is one of the few sponsorships that actually worked on me. I just love the dynamic of a toothbrush company sponsoring a video using their products in an unintended way, LOL

@littlebuch

Ай бұрын

Just get Sonicare. Wouldn't trust my teeth to an Iphone 3gs looking brush

@DoctorX17

Ай бұрын

Yeah, I legit use a toothbrush for that sort of cleaning, lol. And it is a good point that you could have an extra head for cleaning crap and clean ones for your teeth, lol

@ligametis

Ай бұрын

This was a terrible ad. I got tired hearing about this toothbrush from 20 different channels and this was a whole video about that.

@Nukezone100

Ай бұрын

@@ligametis ...sounds more like a "you spending too much time on youtube" issue. Not with the format of the ad itself.

@ligametis

Ай бұрын

@@Nukezone100 that is the point. I can't spend a lot of time on KZread and I do not wish to waste it on useless product ads. Have 10s-1min ad that is easy to skip or ignore. Also advertise something useful like some better alternative to their ltt screwdriver.

good lord david has NOT been skipping chest day. nice work

@gabetessin5837

Ай бұрын

I also notice his large chesticles.

@demacherius1

Ай бұрын

All that time he could be gaming he wasted on looking good... who would want something like that.😂

@Metal_Maxine

Ай бұрын

I think it's years of those huge Steadicam type rigs they use at LMG.

@XxxTheFireEmblemxxX

Ай бұрын

Based on his neck and arms, those are just moobs.

@Sydney_2011

Ай бұрын

That's just fat bro. It looks like he used to be a little jacked and put weight back on

I had to clean my custom loop about a year ago. It was starting to grow mold. Best non-abrasive cleaner I used on the acrylic parts is citric acid. You can buy it in powder form and then mix with water to make a cleaning solution. I used it even on the nickel plated copper parts and my fittings with no issues. You just need to make sure you rinse everything really well.

I love the dynamic between Linus and David. More vids with you two would be great. Gives me the Linus and Luke vibes.

Toothbrush sponsoring a cleaning video? We got to get The Greatest Technician That’s Ever Lived here

@blueisodd

Ай бұрын

god I'd love him to be here

@socramel2841

Ай бұрын

He'd be like your moms toothbrush was used for cleaning 😂

@Mrpuggo0322

Ай бұрын

I SAID DONT IN ANOTHER REPLYBON A DIFFERENT COMMENT

@jcalambert10

Ай бұрын

Read that last bit in his voice.

@EironKyle

Ай бұрын

That vibrating toothbrush will go well with his tiny raccoon-like fingers.

I hope that toothbrush Co paid a lot for this one, this is the longest sponsorship I've ever seen on this channel. Not complaining btw, you worked it in well!

@Icessassin

Ай бұрын

No. It's the longest sponsorship for a video that the item being showcased isn't traditional tech, hell they have hour long sponsored livestreams sponsored by the likes of BIG TECH and because the item being showcased is a tv or a pc peripheral you dont bat an eyelid.

@girlsdrinkfeck

Ай бұрын

overpriced electric toothbrush, my £12 braun has a 4 week battery life and does the same job , all these special priced toothburhses are gimmicks

@eTzTheGamer

Ай бұрын

​@@girlsdrinkfeckworse than gimmicks tbh... Selling points such as stronger than competition are kinda shady and potentially harmful.. There's a reason "the competition" don't want to use the strongest vibration on your teeth. If they wanted to they could just sell a dremel as a toothbrush and it would be "the strongest" but there's an obvious reason why you don't want that

@girlsdrinkfeck

Ай бұрын

@@eTzTheGamer some people like to justify their existence with fancy products. Each to their own. I even buy the cheapest tooth paste 60 cents a tube. Does same job as 20 dollar paste. Only active ingredient is sodium fluoride.

In 10 years of videos, we've never seen Linus talk so much about a sponsor's product. That stuff must be super good

I'm the winner of the Nerdforge PC at 2:25. You guys forgot to add a drain port to it, so I did not have a fun time trying to drain the water that was in the loop when I got it 😢

@userxyz783

Ай бұрын

Linus tech reply to this comment???

14:25 I freaking love this shot. It's like I'm watching a movie with a genuine one-to-one conversation between two people. Awesome job! It's these details that I love about your videos!

@ArtFiendz

Ай бұрын

bruh

@sunday87

Ай бұрын

Came here to write the same. What a different style. Loved it!

@StanHowse

Ай бұрын

You mean an extended Commercial?

@noob4head

Ай бұрын

@@sunday87 I know right, it's simple and probably not that substantial but this shows you they know a thing or two when it comes to videography.

This entire video is nothing but a testament to why you should use the proper cooling additives including anti-corrosives AND antibacterial. I noticed Linus only mentions antibacterial additives at the end. There's a reason why water cooling fluids like Mayhems exist.

@imapirateyarrr4508

Ай бұрын

Yeah I run Mayhem X1 Eco Clear (vegetable based so you can just pour it down the sink) and I just cleaned my loop after 18 months just to re-paste my CPU block. Zero gunk, no particles in the block fins, no living organisms coming out. You need to use the right coolant, and tubing that doesn't contain plasticizer. I use food-grade santoprene tubing meant for restaurant beverage lines. Stay away from any cooling with colors (pigment will drop out and settle in/stain your blocks), get the right tubing like santoprene or ZMT, and make sure you do a good initial radiator flush to get the manufacturing gunk out. If you do it right you're golden with very minimal maintenance.

@SoundsLegit71

Ай бұрын

On a vehicle the radiator hoses are electrically conductive. Take an ohmmeter and test it yourself. That is to stop the engine block and the radiator oxidizing like a battery. That's probably why all the corrosion.

@drwhom2598

Ай бұрын

@@SoundsLegit71 No, it's the additives in your antifreeze/coolant that prevent that. "It is very important that antifreeze or engine coolant is changed every 2 -3 years (4 - 5 years for vehicles with long life coolants) to replenish the additives that protect the cooling system from rust, corrosion, pitting, electrolysis, to gelling and foaming."

@intercity125

Ай бұрын

For really low maintenance, car coolant can work (I use the Prestone Corguard "all-makes" stuff at 33% dilution) - the thing that gets some appeal with distilled & minor amounts of additives is the highest technical thermal capacity of the coolant. Back in the day with non-nickel blocks (the bare copper sort) and absolutely NO aluminium I remember distilled and a silver coil being really popular.

@Icessassin

Ай бұрын

@@SoundsLegit71radiator hoses are electrically conductive as they have metal mesh walls to stop them collapsing on themselves when coolant does inadvertently leak or boil over. No point having a hose if it can't handle the heat of the liquid inside it.

This is a great video - the energy is super fun, the camera work is excellent, not a second was wasted in the edit, the music is exactly right for each scene... well done LMG!

I really enjoyed the back and forth chatting dynamic in this video.

I think Linus deserves an award for most original and sophisticated shilling.

@lenon1980

Ай бұрын

Shiling ? Debatable, but I'm sure as heck to some of us this is legit use case.

@Elerindal

Ай бұрын

@@lenon1980Might sound odd, but I keep old electric toothbrush heads for use with cleaning small areas, grouting etc

@oliverer3

Ай бұрын

Cheap ultrasonic toothbrushes are actually really useful for cleaning in small tight spaces they're like small handheld ultrasonic cleaners

@EironKyle

Ай бұрын

Eh, I'd accept this kind of shilling. Once you use an electric toothbrush to clean tight spaces, there's no going back.

@Alias_Anybody

Ай бұрын

@@lenon1980 That's what I meant. Using an electric toothbrush for cleaning water loop parts isn't crazy, using it as a sponsorship however (considering that's not actually what they are made for) takes some balls.

The second I saw the black debris in the loop, I knew exactly what it was. The anti-vortex foam from a brand new EK reservoir also disintegrated for me back in 2021. I contacted EK and they had this to say "It could be then that the foam was poorly made and decayed on its own just like that. It was a poor foam then. As mentioned before, we can offer you a new foam replacement for free as well as we would suggest you also to use a coolant instead of the distilled water for further use of the loop and protection of the parts from growth and so on" I was a bit upset because it required me taking hours to do a deep clean like in this video, and I certainly was not going to pay for coolant. I used distilled water and a few drops of a copper-sulfate biocide, for the record.

@brumby92

Ай бұрын

Yeah mine started to disintegrate and removed it. Nice that it's included but most people shouldn't use it

@wesley0a

Ай бұрын

I also knew right away what it was. These fall apart even if you are running distilled without additives.

@YoSpiff

Ай бұрын

I work on industrial printers in my day job and we had a batch of defective foam like that get out into the wild in some cleaning units. I replaced one on an install and the bad foam just crumbled under a light touch. One of the bad ones accidentally got out to a customer and destroyed several printheads with microscopic bits of foam.

@JathraDH

Ай бұрын

Its why the anti-vortex acrylic insert is a much better option than the foam. Or you know, just dial down the pump(s) a bit. You really don't need 2 GPM flow. All it really does is create more noise, heat, vortex problems and decrease pump life for maybe 1-2c temp drop at best. I run my flow rate at like 0.5 GPM and my stuff still sits at 45-60c under load.

@drunkenfarmerjohn42

Ай бұрын

There's a generation of Porsches that have a similar problem with a foam block in the air loop that causes bits of foam to shoot out the vents over time. I don't trust foam based filtration in fluid loops for exactly this reason.

Oh man, used the toothbrush almost one month, it works really well for me, strong, and deep cleaning. My old soniccare is now used for cleaning my juicer LOL

never seen a sponsored product fit so seamlessly into a video

the music for the transition in the late 18 minute section is fantastic. Made the whole video better.

No matter how old, dudes will always chuckle when they hear anything that remotely sounds like “doodoo”. Thank you editor for leaving that in.

@SullySadface

Ай бұрын

Also if anyone says something smells funky, we're all gonna smell it and agree

a long time ago, I noticed my clear tubes turning yellowish green. took apart my waterblocks and found a tiny bit of biofilm growing 🤣 cleaned it all out, refilled with 90% distilled water and 10% engine antifreeze/coolant. never had an issue again! also made the pump quieter.

Installing a drain port in my system was such a worthwhile implementation.

dude thats insane, im looking into water cooling maintenance for myself and Linus uploads a video on it while I'm searching for it. crazy.

@choochooChuy

Ай бұрын

how did they heart this comment if it was 1 minute ago

@SwiftestScout

Ай бұрын

Linus sees all, Linus knows all

@cndJokester

Ай бұрын

Yeah full of misinformation 😂

that build montage with old-timey music was something else. I was mesmerized for a few seconds

@StormWarningMom

Ай бұрын

Genius addition. Agreed.

I thought about water-cooling the last time I upgraded, but WOW, I had no idea it was that much of a PITA maintenance-wise. I'm SO GLAD I went with air-cooling.

@meerpirat3418

Ай бұрын

that Video is completely over dramatic. If you do it correctly, you have a drain and you flush out the system every 1-2 years. Takes roughly 30 minutes. done. This System looks not set up properly. You usually have additional chemicals in the water to prevent what they are showing. (Like i assume they just added distilled water and left it as it is)

@evil_mel6430

Ай бұрын

@@meerpirat3418 Exactly and I have seen good setups running like new without flushing even longer than that.

Got ptm for my msi laptop and it was actually easy to use and now its cooler than ever, thanks linus!

Tip for pc newcomers : water cooling is not necessarily better. Just go for a sufficient enough cpu cooler.

@CatSucker

Ай бұрын

Its not cooler, but it is cooler 😉

@Woyta

Ай бұрын

If you have really quiet room, air cooling is annoying. Not to mention during gaming. With my custom loop 12cm fans were spining just at 400rpm. It is not always about performance.

@PortocaliusMaximus

Ай бұрын

well it used to be better, but that was before the thermal assassin and huge blow-through coolers on gpus

@boburanus69

Ай бұрын

Basically, water and electronics are not good together. It's a corrosive relationship that never ends well. If you by some chance build the perfect watercooled PC, never have ANY issues, and your components last until you want to upgrade, there's always the chance a leak happens and your stuff is never 100% again. When I build a computer and I want to keep using it for a years to come, I don't put liquid anything inside it. Or near it.

@figureviews

Ай бұрын

​@@Woyta use headphones

I found the music attached to the cleaning montage from 18:14 - 18:51 to be really fun and unheard from most tech videos. A very nice stylistic choice:) more plz

@personnel5428

Ай бұрын

Yes please, bump this post. Whoever does the music for LTT this was a wonderful choice :D

Had water cooler went back to air love th quiteness of water but i love the simplicity of cleaning a air Cooled system.

I’ve built two computers one with a custom loop the pump wound up failing, second pc was an aio sure enough stopped working,went to air cooler learned my lesson!

Love the musical score you went with when showcasing the PCs after the process was complete. Seemed classy and relaxing at the same time. Would like to see more of this outside the box thinking.

I did my OG water loop with Mayhems Biocide pre-rinse, and then I ran it on Mayhems Pastel for 4 years not giving it even a moment of maintenance, finally when I did it clean it out, all it took was a good few flushes of vinegar in the loop -- easy-peasy. I think if you take the time *at the beginning!* to use an inhibitor and ensure you have clean distilled water as a base for whatever colors/lusters you put it in, it's really not that hard to water-cool in a relatively pain-free way.

@zoson

Ай бұрын

Don't use vinegar in a pc cooling loop. Vinegar will destroy your nickel plating and cause acrylic to craze(spider cracks).

@Alex-zi1nb

Ай бұрын

couldnt you, in theory, run bleach through your set up for like 5 mins to disinfect, and then use the inhibitor and pure distilled water and...in theory...no bacteria should ever show up

@Exzeph

Ай бұрын

Okay but my tubing is PET and my components are bare copper.

@saddane6897

Ай бұрын

I can attest to RO water being supreme for cleaning focus, some preffers Destilled or De-miniralized but RO is just better as a decent filter setup is pretty cheap, and ensures a low solids count below 20ppm right at home. I have a big loop buildt over a long time, with external Rad, Res and Pump, and probly like 3m-3,5m softtube on there in total. I dont use any anti-agents of any kind (beside first time i put it on this Pc, which then grew fungi), i just use RO water now and a T-adapter to make a solids-trap on the pump inlet tube, so the pump is pulling from the side of the T helping solids drop in. But yeah using a T-adapter trap and RO water, i mean i basicly never have to clean my setup xD its been atleast 6 years now since i cleaned it (remove the blinded off trap tube and clean it/Refill) Actually now i need to refill the loop from dissipation loss more often than i need to clean it xD

@Slade111984

Ай бұрын

Agreed, water-cooling isn't that bad if you prep your blocks well, but nickel plated doesn't like vinegar. I've been using a lighter mix of coffee machine cleaner as it's fine with the acrylic as well as metals without stripping. Never had algee and I ran a loop for over 12 months on the same coolant no residue as long as it's clear based and not pastel. Pastel requires some harsher chemicals to flush everything clear again and several flushes with demineralised water .

I love the "Linus does stuff for us for free"-series. Keep it up. Especially David's clean my stuff and upgrade old stuff was entertaining.

This is my favorite video I've seen from you guys in a while! I feel like the camera work was different in a great way. The jokes landed and were not exaggerated. Keep it up 🎉❤

This video was really good, very fun. Shoutout David, he's doing great in front of camera rather than shooting!

The editing style with this one was impeccable. Cheers to the editors!

I've had Corsair XL5 clear coolant with some homedepot clear hoses and its been crystal clean for the last 4 years.

For the Radiator Cleaning that you recommended with vigorous shaking, the good way would be to use a paint mixer saves that sore arms but if you wanna do it Janky, than weld to plates to a reciprocating saw blade and have at it

I think David becoming a writer has been one of the best things to happen to LTT recently! I've enjoyed absolutely all the content he's involved in even when it was just comments from behind the camera lol

@_aullik

Ай бұрын

Having him as a write is awesome, but now i miss the comments from behind the camera. Well one can't have it all.

This felt like such a traditional KZread video you'd find of two friends in a workshop, doing maintenance on a computer. Even the editing adds to the casualness. I don't know, this video just felt so different than the standard structure of LTT videos

@LemmonDP

Ай бұрын

That's because this video was more instructional whereas most of their videos are more entertainment. This actually felt like an LTT video from like 2015.

Very interesting. I've had water cooling for years and currently have my first custom loop (though regretting not adding a draining port to the system) My previous PC had a pump failure after 4 years. A flush of the system with 50% white vinegar for 10 mins (I jury rigged an IV giving set to the loop) and then flushed it with purified water, added a new pump and it ran as good as new. Didn't get much out when I flushed it, and the system is still running now (I gave it to my friend to convert him from X-Box to PC gaming when I built my new system in 2020.

Nice to see someone still rocking the Cooler Master Master Case Pro 5. Such a solid case with so many options!

Linus at 18:05 "cut off the end of the tubes" 18:27 : clearly showing tube not cut off

@vaughanschmidt2130

Ай бұрын

Linus was the one that said to do it. Him saying it however does not necessarily mean that David will do that, intentionally or not. We love you David.

@FieryOnyx

Ай бұрын

Also said, "IF you had a little bit of extra length"

@metaleuman

Ай бұрын

Those tubes have no extra length, they can't be shorter.

@nethiuz9165

Ай бұрын

@@metaleuman That's what she said.

This is one of the best sponsorship videos I've ever seen. It's entertaining and not just an annoying ad read like so many others. Take note companies, this is what you want.

@yourmamaisphat

Ай бұрын

I watched every second of this video. David is amazing, Linus is 10/10 per the norm, and I even thought about getting a new toothbrush! I didn’t, however, think once that I wanted to start water cooling my computer. Very good video!

@yourmamaisphat

Ай бұрын

To be clear to all the people learning from this video, that I’m saying that that’s how good this ad was. It didn’t stop the flow, it was easy to accept that the toothbrush had very tight purpose and that it simply just made sense as a viewer.

@ligametis

Ай бұрын

This was more annoying than any other add because you can't skip or ignore it.

I've been building custom liquid cooling rigs for over 10 years. There's two key facts at play: You need to flush and swap out the fluid every year (we do this on cars, it's not that weird) and you can do that easily with some fab forethought to put a fill port at the top of the loop and a drain valve at the bottom. Use a decent filtration device in the loop at a point you can open and clean it without too much trouble. Use quick disconnects or valves around it. Use an anti-microbial insert in your reservoir. If you use water instead of premade solution, use the most pure option possible, NEVER tap water. If you have no access to lab-grade purified water, then using a high-quality reverse-osmosis system to process the water is needed. Any little bit of minerals or organic material in the water will clog blocks / grow over time. EDIT: I've never cleaned a loop with anything more than common dish soap and some soft brushes. EDIT 2: When you have a poorly designed block that can't be disassembled, reverse flush with high pressure (2x loop pressure is probably a good starting point) using a cleaning solution designed for brass and aluminum. Check your local auto parts store. You can use a high power fountain pump to hook it up. (Fun Fact: all the 655 pumps are in fact originally meant to be low-pressure fountain pumps) I've NEVER had a machine that looks like this video. Ever. Even with neglecting maintenance. I also have been able to overclock CPUs/GPUs with some of the setups to nearly their theoretical peaks without using something unrealistic like liquid nitrogen.

Really nailed the cinematic shots, alternate camera angles and b-roll 👍

loved the cinematography in this video, especially around the 14:30 mark (the over the shoulder "interview" type shot). Keep up the good work.

Chapeau for the creative use of the sponsored item. It didn't come over too forced.

@kg4wwn

Ай бұрын

Just forced enough.

@martinseal1987

Ай бұрын

😂

@joog79

Ай бұрын

@@kg4wwn It was a bit wedged in, true. But i still appreciate the fact that they found a way to make a nice video with a toothbrush brand as the sponsor and incorporate it.

i also had one of those EK anti vortex foam bits dissintegrate in a system that was all EK components and EK pre-mix. ended up seizing up the pump, but was able to clean and salvage it. just a huge PITA

This has to be one of the silliest videos you have made in years... Love it!

Just get a Thermalright Assassin (on a budget) or NH-D15 (pure longevity and customer support). You'll be set for so many future PC upgrades and it's brain dead easy to maintain

@onyxeye5896

Ай бұрын

actually true, bought an NH-D15 and im gonna keep this thing till i die. Maybe i will need to replace the fans in 15 years but thats cheap asf

@casinojka

Ай бұрын

as much as i remember thermalright's phantom spirit should be lilttle better than both of them.

@fly1ngsh33p7

Ай бұрын

@@onyxeye5896 maybe Noctua sells their new fans then ;)

@Alex-wg1mb

Ай бұрын

Frost Spirit 140 is a silent killer. 13900k works perfectly without any power caps but a bit undervolted only 95c degrees max

@jackmillen

Ай бұрын

Definitely, maybe a U12-S for mid-tier systems

I never comment, but I have to say I appreciated the level of detail and information in this video. It was fun to watch, but I also felt like I learned some helpful knowledge.

Back in the earlier days of VR, I used an AMD FX-8120 overclocked 100% stable to 4.7GHz and a Radeon R9 290, both liquid cooled on a completely DIY cooling loop. The loop was made with vinyl flex tubing, a small 160 GPH submersible fountain pump, and cooled by a diluted antifreeze mixture to prevent corrosion from mixing high end copper heatsinks on the GPU and cheaper aluminum blocks cooling the CPU, VRMs, and the 2x240 radiators. For the reservoir I used a large old plastic cylinder container with a nice tight lid, and cut holes for the pump cable and tubes. Sealed them back up with a little plastic welding and silicon sealant. I ended up buying a separate small reservoir pump combo for the GPU and running 2 loops after adding the the VRM heatsinks. With this setup I ended up spending significantly less than replacing the outdated AM2+ motherboard and DDR3 RAM. The loops had to be disassembled once for cleaning approx. a year in due to gumming up of some of the component fins and subsequent overheating issues. After that disassembly I just started draining the loop every six months, ran some cleaner through them, followed by distilled water for a day or so, then switching back to the diluted coolant. It served me well for 3 or 4 years before I decided to get with the times and upgrade. The whole exercise really took me back to the early/mid 90's era of DIY'ing performance solutions when they were either unavailable on the market or too pricey. The old days where school friends were having an arms race to see who could build the best PC on the weakest budget, or who could find a business or family throwing away a PC with a slightly faster processor or compatible RAM for a free upgrade. For the $200-$300 I saved building the loop, I was able to wait just a bit longer for the next generation of CPUs and GPUs, and still enjoy the new "thing" of VR. I feel like with where CPU and GPU utilization is at right now, the performance gains of liquid cooling don't justify the hassle for gamers. Maybe when some of the new features of Unreal Engine are better utilized.

air cooling is always the way! also is tough to find consumer builds that REALLY needs super complex liquid cooling solutions rather then just the top of the line, also unexpensive, air cooling stuff. I kinda also understand that ppl still do that more for looks than practicality, but actually also a nice air cooled build still can be super duper DOPE

The cameraman has his priorities right😂 17:35

That transition from 3:57 to 4:00 is TV quality. Music ends and Linus is talking about the problem with the B roll for context. Chef's kiss

For radiator cleaning along with the water/vinegar mix pour in a bunch of kosher or coarse sea salt it'll work as a mild abrasive to knock off buildup but it'll be easy to clean out.

still making good videos my dudes ... makes me so glad you got me on the noctua hype train a few years ago. I also have been a disciple of Gigabytes windforce cooking systems on gpus. I have a 4070 ti and at 100% the thing barely touches 60c. Before that I had a 3060 with windforce that was the same. IMHO, those cooling units are fucking lit. All the temps on the card are fantastic. Air cooling for life man.

David's got some awesome on-camera energy

Watching you guys water-cool things over the years convinced me to buy a high-end air cooler. best lesson learned from the channel. haha!

Nice to see you recommending Brasso. That's a super-underrated product. I've been using it to clean contact pins or solder points on PCBs for years.

Not gonna lie, this process has never crossed my mind every time I had considered custom water cooling. I'm definitely glad I never went through with building one.

That toothbrush sponsorship was one of the smoothest you've done in a while

Evapo-rust is a good product for removing rust and you can just soak the parts in it as well. There is a KZread channel that restores old products that uses it all the time with great results. Try using it for that pump you're trying to revive.

@mzaite

Ай бұрын

And don’t dump it out! It chemically keeps working even after it looks cloudy.

I'm so glad this toothbrush is wiggling with an accuracy of 0.1 degrees. This is absolutely what i've been missing on all of my conventional toothbrushes.

I absolutely love the 50's/60's rom/com music during the montage.

this video was so good and fun, all these recent david videos were all good but this one is great, everything from the chill vibes, the cleverly positionned discussions bits, the nice watercooling tips, nicely put in with a super relatable storyline, and overall the great editing and pacing

I love Linus Toothbrush Tips.

Random comment: That over shoulder shot was awesome!

Red Line Water Wetter - biocide and reduces surface tension so you can get even cooler temps. It's got a red tint that can dye plastic tubing but IDGAF and it works great. My Swiftech pump has run for like 8 years BTW :) Decorative water fountain pumps, transmission coolers or heater cores and home made blocks were my goto for years. I miss using Peltier but these days processors are just too hot.

Two guides in one. Use this for PTM7950 installation too. Once you cut the PTM to size, put it back in the fridge for a few minutes to give yourself some more workable time.

Really nice looking shot angles on 14:30! Would love to see more of those being used in future videos!

I've had the same pump, res, and rad for the last 10 years and temps are still perfect. Aside from waterblock replacements to accomodate cpu/gpu upgrades and flushing the system twice per year using distilled water w/ anti-organic additaves, (Which takes about 15 minutes) I've had to touch my loop exactly zero times. Seems like LTT just overdramatizing a simple and straightforward setup.

Unironically the best toothbrush ad I have ever seen

This is the exact reason i only bought AIO's that can be "added to", not to add more parts but so i can do fluid changes yearly to keep the fluid fresh clean and full. Buy some CLR or similar to clean the metals and fins

@JathraDH

Ай бұрын

You are probably doing more harm than good TBH. Proper sealed AIOs are filled with glycol and the fluid doesn't go bad, nor do they really corrode, because of the glycol. They can easily last 5-10 years and you will probably be building a new PC before then anyways.

David looks jacked man, nice!

I've had Mayhems UV Blue in my custom loop work system for over 10 years with just occasional fluid top up. No decrease in performance! Using it again in my 14900KS and 4090 system with MoRa 420 🙂

I used an automotive coolant called HT-12 on my loop. I work at a BMW dealership and in 2018 this coolant was introduced and used on all high-voltage components including the computers and even cell modules themselves. Those cars today are basically just computers that can drive and this is the best coolant available. It's not like in the olden days when computer watercooling was starting out and no automotive coolant had to be able to cool the engine and the electrics without mixing different metals in the loop or being too conductive

David hosting yet again let's goooooo! And also the classical music was genuinely so damn good. Please do more of that

David, I hope your build lives long and prospers!🖖

As a kid of the 90’s and 2000’s I always wanted a fancy water cooled PC but knew it was never necessary. After watching this video, I am glad i never went down that route.

Ngl David's tech Upgrade Made me fall in love with the mastercase 5/MC500 and I tracked one down as a result and I love this case the biggest issue is they're discontinued so some accessories are way harder to find

The day I need an app for my toothbrush is the day I need to be taken out back and old yeller'd.

@AB-80X

Ай бұрын

Hey we need to fill those landfills with something. Why not super toxic e-waste...

Love the old-school music at 18:30 ish for some reason, very cool fits the vibe

This is one reason why I always recommend an air cooler of some kind for anyone who needs a system to just work. Cleaning out dust every once in a while is a lot easier than replacing an AIO or clearing out a custom loop.

My first AIO defaulted to 100% pump speed and I left it running like that because it was so quiet I hadn't realized. Took less than a year of operation for it to start rattling, become noticeably loud and basically unsalvageable. And when the water level does decrease, most AIOs don't have fill ports, leading to audible bubbling no matter how your orient your pump and radiator, it always returns.

Ive been loving all the David videos lately! every time i see that hes in front of the camera i know im in for something good!

You guys should try re-chromming the water block so that the exposed copper gets a layer of crome over it again. i believe the chroming can be done through electrolysis and its simple and less time consuming and the end results are worth it

@h3artl3ss

Ай бұрын

Nickel plating would be safer, Chrome creates a toxic gas in the process.

@Woreec

Ай бұрын

Probably the better option would be to use Electroless Nickel Plating since its result is more uniform and can plate complex shapes like the fins better, also much easier since you basically only have to submerge the part in a solution and dont have to deal with electrodes.

@Efreeti

Ай бұрын

Nickel plating, but yeah. That would be a cool video concept.

@brumby92

Ай бұрын

Waste of time. I like the copper patina

@DEJ915

Ай бұрын

@@brumby92 doesn't hurt performance either so yeah, most of the time raw copper blocks are better unless you're using liquid metal.

I must have used the first commercial water cooler back in the naughties, the problem back then was that water would grow algae, so I put Listerine in the system. It didn't slow the algae much, but my PC had a minty fresh smell to it.

You convinced me. If I ever build a pc, fans will the way

18:40 loved the old Disney movie, music 😍😍

Ever since you guys started doing watercooling so many years ago, I always thought about how much of a pain in the ass this would be. I already hate zip ties because I don't wanna cut and re-apply them every time I want to move something.

@bartbasil3704

Ай бұрын

Imagine the custom loop nightmare, where sometimes it's making new loops because it only fits in, but doesn't fit coming out. It's awful.

@noodlelynoodle.

Ай бұрын

You can loosen zip ties pretty easily

Going on almost 10 years w/ current rig - Swiftech Apogee Drive 2 for a 4790k, 240mm rad. Drained every 2 years. I’ve de-gunked the pump every other drain and fill. Quiet, leak-free, and reliable. Swiftech > all!

I watercooled once and was done with it. It took you 25 years to figure this out. Holy man...