Does this circuit really work I have bought the components

@Ciiads

Жыл бұрын

If it doesn't work, what's the point of my hard work and time? Go ahead buddy it will work ☺👊

@zeuszix8009

Жыл бұрын

Bro can u giv ur email. I made it, it does not work

@Ciiads

Жыл бұрын

@@zeuszix8009 Maybe you did something wrong. madebyaneeshmurali@gmail.com Forward the photo of your setup. and component details. Let me check.

@zeuszix8009

Жыл бұрын

@@Ciiads bro please check your mail. Thank u

@zeuszix8009

Жыл бұрын

@@Ciiads I think I found the mistake the shopkeeper gave me 4.7 k instead of 4.7 ohm. Silly shit though please check ur mails thanks aneesh

Wonderful good idea

@Ciiads

Жыл бұрын

☺👊

Simply Awesom ✨️

@Ciiads

Жыл бұрын

😉 nice to see you after a long time.

such a god man thx

Can this circuit be used to drive 24V discs @30V (for higher mist output)? If you want a multi-disc system, can a single circuit drive multiple discs at once or does each disc need it's own circuit? Also, if we are buying the 100uH inductor, what size is needed? Is a 6*8 enough, or is something like 10*12 or 10*16 needed?

@Ciiads

Жыл бұрын

As per the datasheet of the transistor, it's fine to handle higher voltage but you have to use a better heatsink to cool it down. Using thick wires and a thick layout is very important. and also use a high current 100uh to 150uh radial inductor which is also very important, the current capacity of the inductor is all the matter that's why I made one myself. Thin wires and thin layouts and weak inductors cause overheating and unstable operation. I never attempted with multiple disks But you can always experiment with that Good luck Regards AMN 👊☺️

Nice

Hi, dear Indian brother, I did everything in the video carefully and it worked. Thank you. I set it up with a 24V 3A adapter. Do you think I can connect two piezos to this board and it will work well? Your friend from Iran ❤️❤❤🇮🇷🇮🇳

Nice one

@Ciiads

Жыл бұрын

😊

hoçam merhabalar bende bir sis üreten çihaz var çihazzın özellikleri içinde su varsa çalışıyor yoksa çalışmıyor bir şarj aleti veya iki adet 1.5 kalem pil ile çalışmaktadır piezosu bozuldu çalışmaz oldu ben yenisini aldım taktım çalışmadı yeni bir çihaz aldım piezosunu söküp buna taktım çalıştı bendeki piezoyu ona takıyorum gene çalışmıyor ikisini bir bağladığımda ikiside çalışıyor lakin orjinal piezoyu sökersem çihaz çalışmıyor neden olabilir hoçam aynı ölçülerde aldım piezoyu yardım edermisiniz rica etsem

yeah... It's worked budy 🤝🙏, at the first time 4.7R was change with a 4.7k bcoz of shop guy, It taking about 600mA with 12.6V supply in the misting point.

@Ciiads

Жыл бұрын

👊☺️❤️

Does it have to have a 12V and 3.3 A supply or can it vary between that value? I have a power supply bench where it can reach a maximum of 30V but only a maximum of 3 Amps.

@Ciiads

Жыл бұрын

3 is more than enough

simple and effective.. works fine... it only consume 0.6amp...... thanks

Hi sir thanks. What equipment is needed to make a piezoelectric module with a frequency of 2.4 megahertz?

@Ciiads

6 ай бұрын

The same circuit works up to 2.4Mhz

I have 3 Ceramic Piezo 20mm disks rated at 5MHz, 10MHz and 20MHz. What components in you circuit determine the resonant frequency?

Hello, awesome tutorial! I made this following your instructions and it works somewhat, but it's much weaker. My multimeter showed around 3.7MHz. Could that be caused by me using toroidal inductor? (still 100uH). The capacitors I used are also slightly different format - 473j100 (should be same parameters). Sorry if these questions are stupid, I'm still a total noob, but willing to learn!

@stanislavzoldak2198

Жыл бұрын

Running on 12V, 3A (bench power supply). Current in the circuit seemed to be around 0.5A.

@Ciiads

Жыл бұрын

Use thick wires , pump the voltage according to the piezo driver spec and use ferrite core inductor having great power handling (5A++) or wound one your self on a ferrite core with thick wire like I did. It's a self oscillating circuit so the output frequency will shift according to the driver specification, for instance if your driver is 1.7mhz it's output is around 1.7mhz , if it is 2.4mhz then the output is around 2.4mhz

@stanislavzoldak2198

Жыл бұрын

@@Ciiads Thanks, will try those, but first I'll finish an electronics course I started a week and something ago, so I can actually decipher what does what in that circuit. 😅 My piezo is 1.7MHz, that's why I used your tutorial :)

Bom o circuito gostaria do esquema onde posso encontrar ?:

Ok sir it's work for me tks for share....

@Ciiads

Жыл бұрын

👊☺️

hi. what is the size of the wire you use to make 150 micro henry inductor? and how many turns? thank you and i will appreciate your reply.

@Ciiads

27 күн бұрын

I can't recall that it's been a while ago and I think you can use coil32 software to calculate that😊♥️👍, and very sorry for my late reply. Regards, AMN

Dear Aneeshmurali Sir, excellent work and very nicely explained. Many appreciations. One doubt Sir, can we use a cheaper power transistor of IGBT or JFET or MOSFET? The power transistor 2SC5200 is very expensive in the market; it handles 230Volts and carries 30 Amps and so the cost is justified. However, a low cost alternative would be much better and non BJT colution will also eliminate the need of heatsink. Any suggestions on alternate part number of IGBT or JFET or MOSFET Sir? Regards,

@Ciiads

27 күн бұрын

Yes, someone made modifications to the circuit using an IGBT and provided positive feedback about the results. I read his comments further down, but he didn't mention the IGBT part number. He explained the other components well, but I think he forgot to include that detail. Give it a try 😊♥️👍

Hello dear Ciiads, your video inspired me to try myself, but unfortunally i couldnt get it to work with a 2,4mhz piezo, but but but, then i started to experiment and got it to work very beautifully and highly powerful. I used your circuit, with an igbt, and i used a 1,5k puldown resistor from gate to emitter, and i used a 220uH torioidal inductor. And i used a 3k resistor insead of 2,2. I powered with a 19v laptop power supply... This setup works amazing for me. Please share this very important information! ❤ Kisses from Germany. Thank you brother❤! PS I use this to power an ultrasonic e cig tank called usonicig. Unfortunally the company went bankrupt, so u can only buy the pods. I can share more details if you want me to...

@Ciiads

Ай бұрын

That was great, I'm very glad to hear the good news and thanks for your valuable feedback I appreciate your patience and participation, can you share your modified circuit, and mention Your IGBT part number? This is my email: ciiads.amn@gmail.com If you want to contact me anyway. Nice to meet you. With love AMN ♥️🤝😊👍.

Nice circuit, it works. My steamer oscillates at 1.78MHz

@Ciiads

7 ай бұрын

Finally somebody did it, Thank God. It will work 100% and it's not fake, so many people are degrading my work, God promise I never upload any stupid things to grab attention or make money "my intention is Do the best or do nothing." If anything doesn't work that is because of their own mistakes not mine. You did a great job nice to meet you. Thankyou for your valuable feedback. 😊 Regards, AMN

@thelonewolf1757

7 ай бұрын

@@Ciiads However I'd suggest that in the video you show a circuit diagram to your circuits. That way they will be easier to understand. From a circuit diagram everything is straight forward, you know exactly where to connect each component, in what orientation as well. Seeing the circuit itself, without a diagram doesn't make clear where the connections are going. Even more that you are soldering from the opposite side of the board where the pins of the components are in a flipped position to the original e.g, the base of the transistor is at the place of the emitter. Also that will save lots of explanations where and how to solder each component.

@Ciiads

7 ай бұрын

I appreciate your opinion next time I will and I'm considering it. Regards, AMN 😊

Could you make this plate to sell, I always need it here in my city, I can never find all the components, and I can't assemble it

Are indian? If u are dang man u have a very good english I came from the tutorial vid of blue stacks and it kinda makes me happy so ye am here now watching some of ya vids

@Ciiads

Жыл бұрын

☺👊

thats cool man! Can this circuit run the lower disk with 116 khz ?

@Ciiads

6 күн бұрын

@@fauzanhariz9589 no it's not but you can try that with ne555 chip.😊👍

Pls list down the components to buy, if possible the diagram too

I have made this but after running it for 5 minute the 2sc5200 became very hot around 90 degree Celsius, I am using a heat sink as u used in yours, now what to do, is it normal ?

@Ciiads

Жыл бұрын

Use thick wire and recommended power supply read the comments down below solved the same situation 👊☺️

Sir Is this circuit good for langevin transducer 40khz?

@Ciiads

Жыл бұрын

It's not designed for that ☺️👊

do you have schematic on this bro ,

I finished making this circuit and it's working alright, but when I measure the piezo disc against an oscilloscope I am calculating a frequency of 800 kHz. Have you tried measuring the frequency?

@Ciiads

Жыл бұрын

Is your piezo disk 800khz? It's a self-resonance circuit output frequency depends on the piezo resonance and it will vary between a few hundred kHz to 3++ mhz Depending on the piezo resonance and piezo load. Try dropping a few drops of water on the disk you can see the frequency changes on the oscilloscope it will vary and will go up to the piezo resonance frequency and try to verify that using a frequency counter as well.

@azimshaikh4074

Жыл бұрын

@@Ciiads no it is clearly a piezodisc with 1.77 Mhz resonant frequency. Can I contact you through email and share images of my oscilloscope reading and circuit?

@Ciiads

Жыл бұрын

@@azimshaikh4074 is it misting well?

@Ciiads

Жыл бұрын

@@azimshaikh4074 you can contact me but unfortunately, I'm not at my home right now so my reply takes a bit of time. madebyaneeshmurali.n@gmail.com

@azimshaikh4074

Жыл бұрын

@@Ciiads yep it mists okay at 12V and roughly 0.5 Amps. But when I increase this to 30V the circuit is more effective, but produces more heat and over time may damage the components. The signal read on the oscilloscope at 30V is very abnormal and highly erratic. I have sent you my results through email.

Total cost of the components. Can you list out items.

Can I use 47nF 50-volt cap for this circuit?

@Ciiads

Жыл бұрын

Use polyester cap ☺️👊

nice!!! can you please provide the link for buying the items.That would be helpful😄

@Ciiads

Жыл бұрын

I bought that from my nearest electronic store

Hello Aneesh. Very nice video, thank you for that. But I still didn't understand the function-principle. What drives the circuit, where is the 555 bug? 🙂It might be an LC-circuit in parallel, but I cannot bring the values together: f = 1,77 Mhz, L= 100 µH, C= 47nF - they don't fit in the formula f = 1/2 x pi x sqr(LC). Please explain. Bye Matti

@Ciiads

Жыл бұрын

Piezo disk resonance plays the role The LC circuit in the oscillator circuit sets up its own resonant frequency based on the values of the inductor (L) and capacitor (C) used. However, when we connect a piezo transducer to the circuit, it introduces its own resonance characteristics. The piezo transducer has a natural resonant frequency at which it vibrates most efficiently. When the circuit is driven with a frequency close to the resonant frequency of the piezo transducer, the transducer responds more effectively, resulting in stronger mechanical vibrations. This, in turn, affects the overall frequency of the circuit. The LC circuit provides the oscillation and frequency generation, but the presence of the piezo transducer influences the behavior of the circuit by effectively locking the frequency to its own resonant frequency. As a result, the output frequency of the circuit aligns with the resonant frequency of the piezo transducer. So, in our case, using different piezo transducers with different resonant frequencies will cause the circuit's output frequency to align with the respective resonant frequencies of those transducers.

@bigmacam

Жыл бұрын

@@Ciiads According your values the frequency produced by your circuit would be 73,412 kHz. Have you measured in on the scope?

@Ciiads

Жыл бұрын

why are you not considering the piezo resonance the output will depend on it, there are 2 nos of 47nf in the circuit, and this circuit will complete only when the piezo is placed. Did you tried it, on my frequency counter it was never 73,412 kHz Here f is not 1.77mhz like fixed frequency it changes according to the resonance of the disk if you place a 2.4mhz disk in it, it will oscillate within that range.

Hello, this fog generator is 16 mm, I think it is 113 khz. Is there a chance to make a circuit that works with small voltages such as a battery charger between 5 v and 9 v that operates the pieszo? Could you please help me?

@Ciiads

Ай бұрын

You can make 113khz version using ne555 chip which works with 5 to 9v , for further reference there is a tutorial on the Greatscott channel ☺️👍

@enderozata6308

Ай бұрын

@@Ciiads Can you share your tutorial with me so I can search among channel videos?

@enderozata6308

Ай бұрын

titles of the training video

can it run for a long time I mean for an hour ? can u share the schematic, I know it is very simple to make but schematic is more useful...

@Ciiads

Жыл бұрын

Why not?

Excuse me, how many volts am I allowed to add to this circuit? Please answer ❤️

@Ciiads

2 ай бұрын

Depends on the piezo disk working voltage.

Hi, man. What do I change in this circuit to integrate 2.4Mhz mist maker?

@Ciiads

Жыл бұрын

Nothing just install a 2.4 MHz piezo disk, it is a self-oscillating circuit. The resonance of the piezo play the role.☺️👊

@ZholobovSS

Жыл бұрын

@@Ciiads Thanks!

@ZholobovSS

Жыл бұрын

​@@Ciiads And one more question: does it matter to use film capacitor or may replace to ceramic?

@Ciiads

Жыл бұрын

@@ZholobovSS yes 100v polyester would be the better choice

BRO, can you design a circuit with help of working 2.4mhz and 48vdc

Can use 100 uh 2.4 ampsToroidal DIP Inductor for this circuit?

@Ciiads

4 ай бұрын

I've discovered that radial inductors perform exceptionally well. While I haven't experimented with Toroidal dips, you might find them worth trying out. Inductors with thick copper consistently deliver the best results. Best of luck with your endeavors! AMN🤗

@nithiyanandam6148

4 ай бұрын

Thank you buddy@@Ciiads

@nithiyanandam6148

3 ай бұрын

How much maximum wire length can be use between circuit board and peizo disc @@Ciiads

💨

Hello I have made this. I am. Using same same transistor, 4.7ohm resistor 2.2k resistor,0.047uF 63V Mini Boxed Polyester cap. 100uh Radial inductor but it still doesn't work. Am I using some wrong component? No idea about this just want to make a DIY humidifier haha

@Ciiads

Жыл бұрын

Maybe, use what I used exactly, and use thick wire high current inductor 1.77mhz piezo that's it if you did everything right it will work 100%. Read the comments you can find troubleshooting instructions I already helped some guys who going through the same situation as yours. Thank you 😊👊

@Nightflow9

Жыл бұрын

​@@CiiadsI have the exact same piezo disc, bought a whole lot of Resistors but they are 1w(could that be an issue?) But my cap is not same as yours could that be the problem? Also for power I'm using a 12v power from a 550w pc power supply.

@Ciiads

Жыл бұрын

@@Nightflow9 drop your setup and circuit diagram into my mail

@Nightflow9

Жыл бұрын

@@Ciiads what's your email dude

U can use bu 406 trans

سلام با ترانزیستودر D718 هم میشه ?

@Ciiads

11 ай бұрын

I'm not tried it

can you guys explain how it works? does the vibration or heat create the mist ?

@Ciiads

Жыл бұрын

The mist maker contains an ultrasonic transducer, which is typically a ceramic disc or plate. This transducer is made of piezoelectric material, meaning it can convert electrical energy into mechanical vibrations. When an electrical signal of 1.77 MHz frequency is applied to the transducer, it starts to vibrate rapidly due to the piezoelectric effect. As the transducer vibrates, it emits ultrasonic waves into the water. These waves create high-frequency pressure variations in the liquid. The pressure variations generated by the ultrasonic waves create small areas of low pressure, causing tiny water droplets to form. This process is known as cavitation. The rapid formation and collapse of vapor bubbles lead to the creation of mist or fog. The water droplets formed by cavitation are extremely small, typically in the micron range. They are then released from the surface of the water as a fine mist or fog, which can be blown or diffused into the surrounding environment. That's it Good to see you 😊👊❤️

@emergencyimpact369

Жыл бұрын

@@Ciiads than you so much for the replay i do appreciate it LOVE YOUR CHANNEL, so the electricity being used is AC right? for the frequency vibration ? so the electricity flowing on the Piezo wire is AC?

@Ciiads

Жыл бұрын

@@emergencyimpact369 yes 👍

@emergencyimpact369

Жыл бұрын

some electronic devices converts AC to DC for it to function this one converts DC to AC to work pretty cool

@Ciiads

Жыл бұрын

@emergencyimpact369 it's an oscillator

How much power it draws?

@Ciiads

Жыл бұрын

500 to 600 mA but may go up to 1 Amp plus peak current So give it some room, I recommend a minimum 12v 2 Amp power supply

What is the current rating of your inductor? Thanks advance

@Ciiads

6 ай бұрын

I made that myself, and I can't remember the wire gauge. Sorry. It's been a long time ago. Thicker wires are always better. Regards, AMN😊

The diameter is 25 mm. How many volts can I use?

@Ciiads

2 ай бұрын

We can't Guess that , check datasheet 👍😊

Hi! I installed your circuit but I couldn't run it, can you help me?

@Ciiads

Жыл бұрын

Because you did something wrong read the comments below you see I helped many and it's always gonna be a repeated question and answer so read the comments below you will get the fix It will work when you did it right

@roozbehkhodambashi7089

10 ай бұрын

it doesnt work for me as well. there is discrepency of what values for the resistors are. another video has the same circuit but with a different resistor value.

@Ciiads

10 ай бұрын

@@roozbehkhodambashi7089 So sorry to hear that maybe you did something wrong. There is no need to provide the values in the description because I explained everything in the video. the values of every component are there and you can turn on the subtitles if you want. Or even the video is pretty clear that you can identify the values and their color code.

Some times you said 1.77mhz piezo and some times you said 1.7mhz piezo witch one is correct?

@Ciiads

11 ай бұрын

1.77, with 2 decimals, 1.7 with 1 decimal both are correct

PL Z... the circuit diagram

Can u upload circuit diagram with components name

There is a thing like circuit diagram!😜

How i can get 27khz from this circut . Thank you

@Ciiads

Жыл бұрын

Sorry it's not built for that, you can use it with 1.7 or 2.4 MHz piezo disks thank you, for 27khz make something with ne555 or an astable oscillator

Transistor is heating too much.. how to solve the issue ? Not working also. Can u help?

@Ciiads

Жыл бұрын

Use thick wires, a high current inductor, a decent amp power supply, and a heatsink, and read the comments 🤝👍

Can it be made even smaller? Like to fit in a vape?😁

@Ciiads

Жыл бұрын

That's up to you, try to get the smd version of the exact same or equivalent components, yeah, of course, you can shrink the circuit but use good quality SMD inductor having a current handling capacity of 5 amps plus otherwise, it's going to heat up and limit the performance. 😁😁😁😁☺👊

For your followers who do not understand your language, could you post the list of components?

@Ciiads

Жыл бұрын

It's just English the same language you texted back to me ☺️👊 Turn on the closed captions if you need any further assistance 🤝 I spend a lot of time creating that subtitle for those who are struggling thank you.

@alvarofuentesarjona2668

Жыл бұрын

The problem is that I don't have audio on the PC

@Ciiads

Жыл бұрын

It's been a long time ago, I did many things after that so I can't recall But let me try 2sc5200 100uh radial inductor (good current capacity ) 47 nf 100v polyester cap 4.7 ohms 2w 2.2k ohms 2w Use thick wires and good to go☺️🤝 If you have problem with your speaker the CC will help you, please turn it on ☺️👊 Thank you

For me...a schematic digram is needed

@Ciiads

Жыл бұрын

It's a simple circuit and very easy to follow the video but I will consider your request next time.👊😊

Sometimes I don't understand why you make video

@Ciiads

Жыл бұрын

What do you think about your question? ☺👊

@wonderoleg4131

Жыл бұрын

HAHAHAHHAHAA LoL

@Ciiads

Жыл бұрын

☺️👊

The transistor gets too hot what is the problem please

@Ciiads

Жыл бұрын

Use heatsink

@Ciiads

Жыл бұрын

Is that working well ?

@Ahmedmohamed-rs8no

Жыл бұрын

@@Ciiads yes it’s working good but the only problem that the transistor gets super hot with heatsink and I try bu407 it’s the same gets super hot after a few minutes but c5200 it’s more powerful but still got super hot after couple of minutes it’s there a problem with my circuit thank you for your time and your help

@Ciiads

Жыл бұрын

@@Ahmedmohamed-rs8no use thick wires and decent power supply

@Ahmedmohamed-rs8no

Жыл бұрын

@@Ciiads I will try but I use 24v 3amp

circuit diagram？

@Ciiads

Жыл бұрын

Watch the video carefully and follow the steps.

@aaaaa-ct1vn

Жыл бұрын

@@Ciiads 🤣

apart from his fake accent, nice video

@Ciiads

Ай бұрын

Thanks for your judgement but this is how I talk and how my voice is it will be better soon.

Sorry, do you have a schematic diagram ?

@Ciiads

Жыл бұрын

Yes, but inside my brain. I didn't draw the diagram because it's a tiny circuit and very easy to follow. if you are still struggling to follow my video then contact me, and l could draw and share the diagram for you 😊👊

@javo

Жыл бұрын

Sorry my english is not good can you draw the diagram?

@javo

Жыл бұрын

​@@Ciiads hi, could you draw the diagram?

@Ciiads

Жыл бұрын

@@javo no worries 🤝☺️

@Ciiads

Жыл бұрын

@@javo of course

it doesn't work. Please explain otherwise the effort of all these people trying to make the circuit will be wasted

@Ciiads

10 ай бұрын

@roozbehkhodambashi7089 A lot of people are failing because they are not following what I did here. and I feel very bad because I can't able to help them physically I can only talk through comments but that has a limitation. but some of them are attempted more than twice according to the instructions that I provided through the comments and they succeeded. You can find those people in the comments and read their chat history maybe it will help you. I pinned one of them for the people who are facing issues with the circuit. Believe me, it will work. I don't know why people like you misunderstand me. whatever it is, I never make things that don't work but I make things that are too complicated to make. because "if we are thinking about simple we can't achieve the impossible " I don't know about your situation if you did everything right it will work. It only works for those who build well because each and everything in the circuit is so important a little mistake is enough to make it worse. the problem is your build,not the circuit. if you wanna see my build you can come to my place You can see that with your bare eyes.

Sorry brother. Didnt work

This circuit is not working only just transistor heating seriously bro you need to add a circuit diagram this is useless with a proper circuit diagram😫☹️

@Ciiads

7 ай бұрын

Use thick wires and follow the video carefully use right components it will work it's not useless and this circuit is not enough to draw a diagram, only having few components easy connection and it's very easy to follow the video. If it's not working means you made a mistake or you are seeking the video like reading a software lisence agreement. But I will appreciate your point, next time I will draw the diagram for you and the people like you who are struggling to follow my instructions even if the circuit had a single node. Thank you. Regards, AMN

Not working

@Ciiads

Жыл бұрын

Maybe you did something wrong, but it will work when you did it right, read the comments below I have shared some tips with the others like you and assisted those who tried to make this they have the same situation at first because of some mistakes. Please read the conversation between me and Zeus Zix in the comments to fix the issue. I pinned that one to make it easy for you. it will work 100%. Good luck Regards Aneeshmurali

@fikriizakaria2704

Жыл бұрын

@@Ciiads its work but the transistor is very hot with heatsink.and boom hahaha

@Ciiads

Жыл бұрын

Use thick wire and decent high current inductor and a decent 3amps power supply

the fuqs with the accent?

@Ciiads

5 ай бұрын

Appreciate your curiosity! I'm not sure about wtf my accent is, and I hope you still find the content enjoyable. Apologies if it didn't meet your expectations. By the way, I switched my native language to English to make the content more accessible. I'm still practicing and improving. This video is a year old, so I invite you to check out my latest videos for the ongoing progress. Thanks for watching! 👍 Much Love, AMN😊♥️🤝

Just making video and making fool not helpful person not showing clear there is something wrong

@Ciiads

Жыл бұрын

I'm so sorry for what you are going through. You are not watched well right? Everything is clear in there Step-by-step procedure all you have to do is just repeat after me. Read the comments below it helped a lot of people. Here I will not gonna post anything to fool anyone but fools always think their way that is not my problem, that's theirs I can't do anything about that but I'm always here to help you. If you watched the video carefully and you followed the instructions as per my video you will get the same output as what I have shown. if you don't, then you did something wrong but no issue we can fix that. If you have any issues with this build Explain your situation I'm always here to help you. We are just a word far. don't judge a book by its cover Fools are always fools. Next time, think before you throw words. Thank you. Regards, Aneeshmurali

इंडियन इंग्लिश बोलो साफ-साफ जो भारतीय लोगों को भी समझ में आ सके जरूरी थोड़ी ना है इंग्लिश ट्रांसलेशन बोलना है क्या समझाना चाह रहे हो यह पता नहीं चल रहा ना कंपोनेंट बता रहे हो

@Ciiads

Жыл бұрын

Sorry I can't understand Hindi 😔

@MalluTrollen2024

Жыл бұрын

@@Ciiads take translation

@arun.sekher

9 ай бұрын

​@@MalluTrollen2024 The person going by the handle designerpotplanter7555, who is complaining about the video host not using Indian English, ought to take note of your comment.😀 @designerpotplanter7555, इस वीडियो के सावधानीपूर्वक चयनित वीडियो प्रतिलिपि को Microsoft या Google अनुवाद में नकल करें, और आप वीडियो में उल्लिखित हर एक चीज़ को समझ सकेंगे, सहित ही इसमें प्रयुक्त इलेक्ट्रॉनिक घटकों और उनके मूल्यों को। (कुछ तो दुनिया ही चमक जाएगी, ना?) 😇

is it easy to make a 10 mhz mist maker?

@Ciiads

6 ай бұрын

Nothing is impossible if we work for it. Nothing is easy until we master it. Give it a try. Regards, AMN.🙌😊

@mohammadhashemi1771

6 ай бұрын

@Ciiads thanks cii I know that I'm asking your expertise do you think it would be easily put together

@Ciiads

6 ай бұрын

It's not a one-word question, we have to experiment and develop some sort of design for that. Where did you get a 10Mhz piezo? Have you found any driver for it?