exactly what I needed, thank you so much!

👍👍👌Many many thanks. I was looking for it.

Excelente!!

Can it run in 5v

Good job

Very good👍

Very nice 👍

Hi sir thanks. What equipment is needed to make a piezoelectric module with a frequency of 2.4 megahertz?

Muito obrigado, excelente

👍👍👍

Keep it up.

Is it possible to put more than one oscillating head for the same electronic circuit? Grateful

لو سمحت ممكن اعرف اذا كان اي نوع بيزو بينفع ولا لا واريد مخطط الدائره

वाहबहुतखूब

Please I want answer how long it continuously stays on (atleast 12 hours it can stays on ?)

can u regulate its power, a dimmer?

Как можно повысить мощность схемы, чтобы использовать более мощный излучаатель?

nice

I am the first viewer, yeah. Keep up Sir.❤❤❤❤

Components: NE555 10k variable resistor 220uH inductor 100n ceramic capacitor (2 units) 1n ceramic capacitor IRLZ44N 113Khz Piezo

@misha2323

Жыл бұрын

And 1x 10ohm resistor

@Skill002

9 ай бұрын

Sir i have mist maker board it turns off automatically after some time. But i want continuously on, How to make it continuously on, I need to do any short on ne555 ic ???

Pls make fm reciver

مرسی

Can we iuse 1.7mhz piezo?

👍

9v per bhi ye work karega yaa nhi

I want to spray the water mist to little longer distance , so how to do it ? Can i boost the piezo electirc disc by transistors ? Or can i get little long distance by buying big disc than before ? Plz clarify 🙂 i am currently involved in project , plz help me ❤

I would like to use this ultrasonic transducer (400EP125-NBPN) to replace the standard microphone capsules. It is still piezo but with high resonance frequencies. What can you tell me about it? Thank you very much.

How to add a second channel for 2 mist makers? Can you give me a circuit for that?

Schematic?

Nice video and schematic!

@TechIdeasAG

11 ай бұрын

Thanks!

How does it work? Can we add parallel more piezo? How can we set streanght of the mist?

CRT TV bord trasfomer invtor

Quantos volts

🙏👍👍👍

Why mine isnt working

My IRFZ44N got burned out it has simple heatsink

Circuit please

01:37 Incorrect schematic, pin No. 7 of 555 timer is not shown

i have a circuit board that replaces the humidifier circuit but it gets extremely hot and does not work. I want to know why it is not working, please help if u can.

Devre güzel ama o piezzo her yerde bulunmuyor çok aradım ama yok

Can you make this in a small plastic container for nebulising Asthma medication (Rx Duolin). Make a proper plastic chamber with a waterproof chamber for circuit board and sell it at medical stores. Open a company.

Sir can we use 5volt supply

@TechIdeasAG

Жыл бұрын

Fog will be small, you can use 12v battery or even 12v adaptor

@Physicsstar310

2 ай бұрын

9v per work kerega

Hey do you have a circuit for 5v input?

1st like

Sir please watch my video about humidifier self trigger. But it was mechanical some time dust cause non working So i need electrical thing that trigger itself on

1st view

like

Can we use pizzo removed from digital multimeter?

@TechIdeasAG

2 жыл бұрын

Nope, that's not for higher frequency like here

bro mosfet heat ho raha hai kya kru reply me

@TechIdeasAG

Жыл бұрын

It's normal, you have to install good heatsink to it.

@AllArtAndCraft

Жыл бұрын

Bhai iron ki tarah garam ho raha hai

@AllArtAndCraft

Жыл бұрын

Inductor thoda alag lagaya hai is liye ho raha hoga ki ????

@AllArtAndCraft

Жыл бұрын

Plz reply this is my project

@flywithme