Thanks for all the suggestions about the torque on the socket. The seller didn’t send me a torque wrench with my purchase. It is eBay after all. 😂 I do think I accidentally got the pressure right for the final mount considering that I got it to power up. However I will get an appropriate torque wrench for the follow up video.

@grumbert

10 ай бұрын

what's the model of motherboard?

@colestowing8695

10 ай бұрын

(copy pasta from another comment string) the early epic's were extremely sensitive to mounting pressures. Even mounting the heatsink could wind up screwing up memory channels etc. There's a pretty specific way you need to install the processors and hsf's. And yes, it can take a longgggg time to do memory training...like i seem to remember it could take upwards of 10-15 min or more sometimes (although you probably would have seen some signs of life if you got to the memory training phase). Anyway....looking forward to seeing you figure it out 👍 (Edit-you should send Wendell a message from "level 1 techs"...he lives and breathes this stuff. I'm sure he'd be happy to help you out)

@WhiskyNerd

10 ай бұрын

yeah go ask Lius for one. He has like 10 of them.

@chubbysumo2230

10 ай бұрын

I would also check what pcie lanes are assigned to what slots, it may not be able to boot a video card off of the second CPUs pcie link

@itsoowan2763

10 ай бұрын

please release touching cpu cooler video

These CPU retention brackets need to be torqued to a specific spec. if that's not the case you could get bad contact on the pins of the socket to the CPU and that can end in a no-boot scenario. Usually, if you buy these CPUs ne, there is a tool included. That is missing in you case, Dawid. I suggest getting your hands on one of those tools ans try again.

@DawidDoesTechStuff

10 ай бұрын

Thanks for the suggestion. Will definitely get an appropriate torque wrench for the follow up video.

@chriscalderon1337

10 ай бұрын

Yeah they even give you that specially clicking, orange, T-shaped, torx screwdriver with Threadripper! I remember it when I built a 1950X workstation back in the day.

@the_wiki9408

10 ай бұрын

It honestly should still power on with NO heat sinks. It would just overheat and power off in 60 seconds.

@Shire_Sam

10 ай бұрын

Also remember that server hardware takes a LONG time to fire up properly. I noticed at the front there was a little green light flashing? Did that give you an error code of some type? Did you try plugging a monitor into the onboard VGA to see if that gave you an output? I'm not sure if it was AMD CPUS but at some point they (HP or Dell I think) started locking CPUS to specific motherboards so that they would only work in that specific combination. Thank you for such entertaining videos good sir 🫡

@MrFaraz12

10 ай бұрын

​@@the_wiki9408He's talking about the retention bracket screw, not the heatsink ones

The network port above the USB plugs is ipmi I believe, you should be able to plug that in, then go to the IP address that gets assigned to it in a web browser and log in and the board will probably tell you what's wrong, and you should be able to power it on from there as well.

@reinekewf7987

10 ай бұрын

The ipmi will Report you his issues. I think the Jumpers are incorrect or some vendor Lock in ither Case the ipmi tells you

@DawidDoesTechStuff

10 ай бұрын

That’s a great suggestion. I’ll look into that for the next video. 👍

@frederichardy8844

10 ай бұрын

Yes and usually you cannot turn on from the front panel until the ipmi server is running (and the ipmi is not very fast to boot...)

@reinekewf7987

10 ай бұрын

@@frederichardy8844 yea it is slow but If ITS running you dont need a grafikcard for fiddeling in BIOS and com comandshell boot but If it is requerd you can use every GPU you want but die the Most time i use a t100 it smal no extra Power and can handle Windows easy

@FarrellMcGovern

10 ай бұрын

I was going to say the same thing. I used to support huge racks of servers, including dual CPU Epyc, Intel, Power6 (and above) AIX, HP-UX, and all those other fun letters. IPMI port needs to be connected to a system and booted through it to do the initial setup. You can then configure the MB to boot directly to the internal media, that is what those USB and SDcard connectors on the MB are for. You would, for example, have VMware installed on a USB Stick or SDcard, and boot from it, then either have internal HDs, or space on a SAN/NAS/SAS that would have all the virtual machines and such. Lots of fun...yes, I am strange. 🙂

Keep in mind that you have to use the VGA out. It might be different now, but for my Supermicro board, the VGA is the only way to get into bios. In all of its 640x480 glory. A GPU will work fine in windows, but until windows boots, it doesn't show anything for me.

@righteousone8454

9 ай бұрын

He didnt read this comment. He spent weeks trying to figure this out. Then made new video on it. Only if he saw your comment,man 😅

@jonlangfitt

7 ай бұрын

Ah yes, supermicro. When I started getting back into PCs right before the dark period between rx4-500, I started out with free trash 771 workstations as my younger coworker was really into XP - 7 era stuff. For years he was always pushing supermicro for compatibility. I had a couple over the years but they were never more than 2 memory slots and were basic boards. The one supermicro board I kept was an mATX 1150 board for a NAS that i wanted more than just 1 x16 and 2-3 x1 as I was running sas cards and wanted at least x4 on two. I also already had a shit ton of various DDR3. The board claimed to work with the i3, celerons and E3 xeons, but not the i5-i7s. The single 1150 i5 I had came before the xeon and wouldn't post, but i had another 1150 board coming for my kid's PC at the time (hence the i5 while i waited for the xeon in the mail). His board had a couple of pins smashed down I was able to re-articulate with micro tweezers. Put in the 'tested' i5. No post. Start the process for returning the motherboard, seller is fine with taking it back, the e3-1230v3 arrives. Before I ship the bad pin board I put it in. Posts immediately. I end up getting another i5 that comes up later. So in the meantime my kid has my nas cpu and my coworker insists that supermicros limited ram compatibility for my particular board is near imaginary. I get the i5 in and swap it into his PC. I put my generic 1333 ecc dell memory that usually works with everything else, no post. I try some matched crucial, no post. I try my all of my 1600 sticks individually, only one stick of random 2GB works. I sell it off to my coworker as he swears he'll get it with his sticks. He ends up going through several sets with the similar results with memory from his server and workstation stash. I end up buying it back to give it another go. The listed sets that were supported were hard to find secondhand except for one set. I bit the bullet and bought the RAM, but then put my nas off until I found a 4 U case I liked and gathered SFP+ equipment. Time passes, I swap the i5 out for another i7 equivalent xeon and pair it with my old rx580 to my kids pc during a case upgrade. For fun I put the i5 in the supermicro with random non ecc memory. Forums, cpu support and bios update documentation all claim the i5-i7 aren't supported. Fucking thing posts. I still have it to this very day, I doubt I'll ever get rid of it willingly, even though I low key hate it lol Only supermicro board I've ever had issues like that with, but damn was it a bad taste compared to their 2011 and 1156-55 boards I'd used prior.

Dawid, those cpu socket lid screws have to be torqued for the cpu to make contact with the pins. They usually have an included torx wrench.

its most probably a mounting issue as you need a a proper torque wrench with the correct amount of torque id suggest watch Linus videos he's had this issue before

@LinusTechTipsTemporary

10 ай бұрын

This

@DawidDoesTechStuff

10 ай бұрын

That’s interesting. I’ll get a torque wrench for the next try so I can properly dial in the pressure. I think I did get it right for the last mount, considering the fans spinning up and all that. Interested to see what the proper RAM and mounting pressure will do.

@PointingLasersAtAircraft

10 ай бұрын

This is what I thought.

@samjonesmartin

10 ай бұрын

also possibly could be doing memory training. The ethernet port on its own will be a iLO (or out of band management) port that will give a web site showing the bios error codes most likely could be worth trying that.

@DawidDoesTechStuff

10 ай бұрын

@@samjonesmartin That sounds super useful. I will definitely give that a try. 👍

Before Power On 1. Check that the LEDM1 is blinking before the motherboard is turned on. 2. Check that the LED3 on the motherboard is on. 3. Make sure that the power connector is connected to your power supply. 4. Make sure that no short circuits exist between the motherboard and chassis. 5. Disconnect all cables from the motherboard, including those for the keyboard and mouse. 6. Remove all add-on cards. 7. Install a CPU, a heatsink, and at least one DIMM on the motherboard. Check all jumper settings properly. Make sure that the heatsink is fully seated. 8. Use the correct type of onboard CMOS battery (CR2032) as recommended by the manufacturer. To avoid possible explosion, do not install the CMOS battery upside down. No Power 1. Make sure that no short circuits exist between the motherboard and the chassis. 2. Verify that all jumpers are set to their default positions. 3. Turn the power switch on and off to test the system. 4. The battery on your motherboard may be old. Check to verify that it still supplies ~3VDC. If it does not, replace it with a new one Manual Fro SuperMicro

@Felix-ve9hs

10 ай бұрын

It looks like there isn't even a CMOS battery installed in the first place...

Could the issue be not the correct torque on the cpu hold down? if I remember correctly threadripper used to come with a torque driver. Just a thought.

@ShinnaDEW

10 ай бұрын

I was about to comment the same.

@TheRealNeoFrancois

10 ай бұрын

yep,you need it to be exactly the correct torque otherwise it wont seat the cpu properly and could even damage the mobo

@damianosplay9457

10 ай бұрын

I really dont think that is the issue

Those epyc need specific torque on each screw to seat properly. You need to find it or get the driver that would have come with the cpu.

You might want to torque down those cpu mounting screws a bit more. AMD gives a calibrated screwdriver just for that.

@raven4k998

10 ай бұрын

the question is how those ryzen thread rippers got killed maybe the motherboard killed them🤣

@kadrix732

10 ай бұрын

​@@raven4k998We don't know that they're dead. If they're not torqued down properly, they won't work.

@raven4k998

10 ай бұрын

@@kadrix732 sure that's gotta be it they are not torqued down properly🤣 that's it exactly which is why they sold the whole system for 400 dollars makes no sense at all unless they were dead to begin with that's how ebay works got a dead system sell it off to someone whom wants to try and fix it simple

@AlaskanGamerGuy

10 ай бұрын

@@raven4k998you don't understand how the value of quickly advancing technology is incapable of retaining value for any actual length of time.

@ArtisChronicles

10 ай бұрын

​@@raven4k998 I've seen people have issues with actual threadripper CPUs similar to these issues because they weren't making proper contact. It's an actual thing.

i love dawid doing the stupid stuf im to broke to do its super interesting and he does the kinds of things i know i would.

@HUYI1

10 ай бұрын

this is pretty much overkill science project but it's hilarious that he is trying to get this thing working 😂😂

@powerfulshammy

10 ай бұрын

what build a server 😂

I am gripped by this saga, well and truly. Can't wait for part 2, with a nice cuppa to boot.

@Ass_Burgers_Syndrome

10 ай бұрын

And Rich Tea with it or no? Cos a drink's too wet without one!!

@BarryTGash

10 ай бұрын

@@Ass_Burgers_Syndrome I prefer shortbread biscuits - I can say I don't add sugar to my tea but secretly I'm just dunking it in instead.

did you try mounting the cpu by torquing the screws in the right order to the right torque value? ya know, like you're supposed to?

There's an order in which the torx screws must be tighten also those connector are for an storage array!

Seeing you install the CPUs without the pressure torx screwdriver that the socket needs to put the right amount of pressure over the motherboard pins put me in pain.

Didn't those Epic CPUs come with a torque wrench. For installation

@DawidDoesTechStuff

10 ай бұрын

Nah, it wasn’t in the box. Can’t expect much from eBay sellers. 😂 I’ll get a wrench for the follow up video.

this is 100% mounting issue, normally amd gives you a torque wrench that helps you with the correct force you need to give it

I like the fact that Dawid shows the failures. As any of us who have been immersed in the PC sphere knows, sh*t happens.

@AlaskanGamerGuy

10 ай бұрын

I think his failures make for his funniest videos. They're why we are still watching his content.

@ilichio

10 ай бұрын

His channel could be named the idiot with PC parts. It's part of the show.

@AlaskanGamerGuy

10 ай бұрын

@@ilichio I would still watch. I'm glad that he hasn't become obnoxious like so many smaller you tubers that think behaving outrageously works just as well and is much easier to accomplish.

I'm so incredibly disappointed that it didn't work. I was on the edge of my seat... Glad that you aren't giving up. You are a real hero!

Those CPUs need to be correctly torqued like the threadripper or they won't work.

You must use the supplied torque wrench to get the system working. Sadly being used you did not get this. But they are only ~20 USD. Without it the CPU is likely twisted in the socket with pins not making contact. These are a behemoth of a CPU that must be secured properly.

Jesus dude the way you screw the cpus down made me hurt inside you have to carefully turn each screw a step at a time to apply even force across the cpu onto the board. I won’t be surprised if you screwing on side down fully and then the other has damaged something preventing booting. Those “were” working but poor handling as per the evidence in this video probably killed them

2:10 one of those network ports will likely also be a remote management port: a computer in the computer that hosts a webpage that lets you start, stop, and reboot the computer. It will _probably_ also let you remotely control the computer but ymmv on if you need an ancient version of Java filled with security holes to run it. These management ports typically have diagnostic information such as voltages from the power supply, fan RPM, and sometimes what CPUs+memory configuration it sees.

0:10 - great Arnie impersonation 😂😂😂

Be sure that the board and CPUs are compatible. Some of those server boards only work with certain CPUs. You may also want to try going IPMI into it if the board supports it or going in the VGA/Mesozoi port.

You may want to try the VGA port on the motherboard. Server boards usually have an aspeed video chip and dedicated network port so you can remotely change bios settings over ethernet. It has to get though that nonsense before it even thinks about booting the cpu.

hell yeah lets gooo the next videos on this server stuff will be so freakin awesome

I think I've seen this issue before.... It's because supermicro uses their weird proprietory connector which fit in x16 but actually pcie x8 with different output lanes so that a normal pcie device couldn't work. The connector is used for a storage such as SATA and NVME. I've seen the converter to a normal pcie but I never tried it. This problem also happened to my old supermicro server, the difference is I'm still using lga 2011.

This is Epic, no pun intended, awesome stuff mate, can’t wait till part two!

If cpu isnt mounted correctly it may do that that also explains why it booted for a second there. These sockets do require a lot of mounting pressure so maybe you have to really screw it down (I think they come with a Torque driver and recomanded specs). The board has ipmi so trying that would be the first thing you should do.

yeah as mentioned before i strongly believe that is the CPUs not making proper contact since these need to be torqued with the bright orange thingy they include when new.

Man I love how straight up you were with it you’re like this just isn’t working like it’s broken 😂

It could be the IPMI needs time to boot before the system powers on. Not sure but the blinking light beside the Aspeed IPMI chip is an indicator. Also, you should torque town those CPUs with the AMD Thread ripper/epyc tool.

@b127_1

10 ай бұрын

Yup. I've a supermicro board and if you power it in immediately after plugging it in, it'll sit there for a minute waiting for the BMC to boot up. I think it even outputs "waiting for IPMI" to the screen.

@splitprissm9339

10 ай бұрын

@@b127_1 Usually fans will already spin up when the IPMI is initializing. But yes, it can mean you'll nervously wait minutes until anything comes on screen.

When you buy used non-pin CPUs and RAM you always should clean their contacts with eraser rubber and ethanol. They always get an invisible film of rust/oxidation which acts as insulator.

Ive seen these combos on ebay and they were very interesting. Thanks for taking the plunge on one of these.

@mr_jarble

10 ай бұрын

I really dislike this video as it gives the wrong impression. With some thought into part selection you can easily get amazing systems up and running. I have a ebay sourced amd server and had none of these issues.

Zen 1 cores, so no official Windows 11 support hence why it is inexpensive

Nice to see you have fun with those, in case you are wondering those SD cards are sometimes used for OS on setups where you need no storage just compute.. anyway using a single 7702p mainly for pcie 4 and for more pcie on the MBbut first gen are alot cheaper per core but older servers are often a ton of bang for the buck!(if you dont need insane single core). Also said it didnt work out usually i pay like 20% more to buy it of local sellers because i trust those more but hey even there sometimes you get things that dont work.

From what i see it most likely a torque issue - these CPUs require a lot of torque on the socket screws, it is by no mean "finger tight". I do not think that it is a memory or cpu vendor lock issue because these manifest much later and you would see the fans spinning. To this theory the bad spread of thermal paste adds up as well - looks like cooler bottomed out on the socket instead of the CPU itself. Also, in order to get more information - assuming you just apply more force to screws - just connect an external VGA display to this mesozoic port, these boards come with IPMI management chip (it is active since it blinks green when board is fully powered and it booted up) and it starts outputting debug information to the onboard VGA before it even initializes PCIe devices so you will get information much sooner.

I love it when Dawid Does Tech Stuff!

I like how it slowly turned into a tech blog big brother giving us Dawid's weekly tech battle. You're amazing, Dawid!

Ahhh man, was hoping for it to boot, can't wait for your next video

1 yes you need the torque wrench and 2. the memory training takes LOOONG so just give it a solid 2 to 3 minutes once you got it torqued right

Server/enterprise-grade equipment and hardware is very difficult to get running, but if it runs, it runs till the end of time

None of your videos are pointless. At the very least they're a chance to say Linnnoooooooooode. And even when nothing works, you keep it entertaining. Nicely done.

I NEED to do Dawid with a silly machine doing dastardly things to it. That is all. Love the channel.

Hi, on my server mainboard, i need to close a contact for open chassis. On a other Mainboard (HP) all FAN Slots need to be connected. is there any clue in the manuel?

I used to work for Atech. Always a joy seeing their relabel sticks going in machines.

really enjoying your video's that stray from the normal, but also looking forward to seeing you game on a 64 core epyc system.

i caught your vids on and off for the past couple years now. dont know why ive never subbed till now... great stuff

This is a server board even in 2023 they’ll still come standard with vga as data centers don’t care about image quality just to check and make sure everything’s running right source I used to build them at my previous job that I quit in may

In those types of motherboards, I believe you have to run dual CPUs or install a continuity module for the "empty" CPU socket. it does sound like one of the CPUs was dead though if you weren't getting any power with just one, or possibly one of the sockets on the board is bad.

It could be the fact the mobo doesn’t like not having a power switch, I had this issue with my old 5000psl mobo until I got a power switch from Amazon and tried all the configurations on the panel pins. After that if powered on.

That thermal paste application gave me chills. I've had to replace a few EPYCs on my job and we have a giant pre-formed thermalpad that covers the entire surface of the lid

These chips are tremendous! Did you get it to work? Ive helped build several for people and always managed to resolve any issue.

Just good to know that kinda stuff exists, thanks, Stefan

@08:18 thanks for showing us what fans turning looks like lol

Great video Dawid. I am on my second server motherboard from Ebay, but mine are a bit older. I currently run a Supermicro dual socket with 2 Xeon X5650 and modern coolers. Keep up the good work and good luck with the project.

This is slowly becoming my all-time favorite tech channel. Love the videos Dawid! Hope you can get this thing running!

@a.filakiewicz2942

9 ай бұрын

Yeah, its like all the mistakes i was thinking of making, but they dont cost me a thing.

In case it hasn't been mentioned already in the comments, you need the proper torque screwdriver that usually comes with the cpu to mount the cpu correctly. :)

It could be a pressure issue, the three retaining screws on EPYC and Threadripper sockets must be torqued down to a fairly specific amount - if you get the torque wrong (and yes, too high is also wrong!) some or all of the memory channels and/or PCI channels often won't work so that's another possible reason though usually at least ThreadRippers tends to get to the BIOS screen. But since it's a server they MAY have decided you're supposed to check the BMC information for that instead.... The ASPEED Baseboard Management Controller runs completely independent of everything else and you connect to it via the dedicated (third) network port. That should be your first place to check. All Threadripper retail packages includes a yellow bespoke torque-controlled torx screwdriver that goes "click" when you hit the right amount so they're fairly easy and cheap to get on the second-hand market. I've seen blue ones that presumably comes with at least some EPYC processors (matches the 7xx1 carrier board color) but a EPYC one should work. It's NOT impossible to do this without a torque wrench but it's definitely not trivial even if you've done it many times! Looking at SuperMicros memory list I'll note that it's VERY small but also that all the few 16GB sticks it does list are 1Rx8 models, not 2Rx4 like the ones you bought. It does have some larger 2Rx4 sticks so it clearly supports x4 chips which means those memory sticks MIGHT be supported but... risky. From any of the other large vendors the manual would spell out exactly what memory is supported but not with SuperMicro... The other source is various memory vendor memory configurators - Crucial only show 1Rx8 models for 16GB but that might be because the memory chips required for 2Rx4 is, well, long since out of production and they're selling new memory. Kingston's Memory Configurator usually has a side-bar telling you what the hardware supports (in addition to "these current server memory sticks will work) which is really neat but... their entire site is down for maintenance Sigh. The manual does say how to officially run it just one memory stick and one CPU (and 2/4/8) but two cpus officially needs all 16 memory slots populated, I expect this is completely bogus.

Another Dawid moment of dawiding

Those are torx bit screws, very common anymore at the hardware store for things like deck screws and drywall screws. Make sure to get the right size, there are about 6 sizes all pretty close. They don't slip and cam out under high load like Phillips bits do.

Good luck hope you work with servers before, that cpu and the tread ripper are server based , accessing as someone mention has to be done via the network port, good luck can’t wait to see if you can get it working

happy to help you figure this out as there were quite a few things done incorrectly in the video. - CPU mounting: the cpu has to click in with those blue tabs then you put the retention bracket and torque it to spec (must have tool for that, comes with threadripper CPUs typically, not sure about epyc). Thermal past application, use 9 dots at least - RAM: do NOT EVER use non-ecc on server mainboards. check carefully online and the manual to confirm compatibility. Check manual for which RAM slots to use if not fully populated. You can fry normal DDR4 sticks if mounted in server. - you don't need a GPU, you can connect a VGA monitor to see the bios screen and get the IPMI IP address. There is like a small computer within the mainboard that manages the big PC and gets you plenty information about your components (without even booting the PC). I think those flashing green lights mean it is powered on and ready to use. - The Ethernet ports are not all for the PC. One of them is for the IMPI remote management system. Make sure to check which one that is (manual again) then connect it to ethernet to be able to use remote access. - use the IP address displayed in bios boot screen. type it in your browser, then you can access the ipmi. - remember that it takes a couple of minutes for the on-board IPMI (small computer on the mainboard) to boot up. hope this helps. There are a few more precautions. reach out if you'd like some more help. This hardware is tricky to get running. Once you do, you can add multiple GPUs, everything will run at full speed as you have a ton of PCIE lanes

Not sure if that changed on Epyc, but you will usually not get POST with CPUs installed but no memory. Also, server motherboards usually require the correct memory positions to be filled - so please double check in the manual. Easist process is to start with just one CPU and the least amount of memory possible, then start changing memory modules untill you have any signal. Like other people commented, server motherboards can take a long amount of time to do anything. Another thing that comes to mind, maybe the BIOS is not updated for this specific CPU? That would be problematic because you would need a supported CPU in order to boot and uptade BIOS. Well, good luck! Part of the fun is getting it to work :)

Good luck! Looks like an idea I may try tot rebuild my home lab. Any info on the MB make and model?

All those ram slots are so satisfying to fill, yet such a pain to troubleshoot. The Dell Precision Towers my work uses have 8 Ram slots and its just glorious to look at them all filled.

Love it! You brave the tech jungle and send us the reports. Awesome stuff.

These motherboard are equipped with an onboard graphic chipset. I would recommend to boot the motherboard with no graphic card and a display connected to the vga port

I actually bought the same board (H11DSi-NT) from them (but with two EPYC 7302 instead). I had 8 64GB ECC RDIMM populating all DIMMs for CPU 1 and it booted up as expected. I think you should be able to diagnose exactly what went wrong by going into the IPMI management page as the LED to the left of the board is blinking green, so the board has started up successfully. The user name and password are printed on the board (the sticker to the right under CPU2 DIMMS). Also, consult the manual and see which DIMM slot for CPU1 needs to be populated in order for the board to boot and torque the CPUs up to spec, I heard the board is really picky about these as well. Hope this helps!

The socket specific torque wrench tool wasn't included with your mobo. Ask the seller for it as that is going to most likely be your issue. Notice the tightening order for the screws printed on the cpu bracket? Thats the order you torque them in.

@LinusTechTipsTemporary

10 ай бұрын

THIS

Damn I was excited to see this running. Guess I'm just gonna have to wait :)

I love the 1980s self realization comedy movie soundtrack you always use.

It's Always fun watching you strugle bro :))))

On the server board, you have OOB to fully control the chassis. So you don't need to jump the power pin nor need a GPU to have an output.

that scream LMAO, that is me after being frustrated with computers also 🤣🤣

Love your vids!

I went to work today and nothing worked. So seeing this video of nothing working certainly cheered me up. Thanks Dawid :)

Don't know if it applies to this build or not, but some server boards require some kind of memory cooling shrouds in order to work properly. Guess cause the memory sticks can get a little toasty, but I don't know about these things all that much if at all.

I'm somewhat convinced the Ebay Seller is like, 'Cool, I have some noob who will buy all this potentially broken hardware... sweeeet'

@CapComa

10 ай бұрын

Jeez... Tell him to read the manual and check the LEDs/jumper configurations. It works fine, he's just lazy

@LinusTechTipsTemporary

10 ай бұрын

@@CapComa No he needs to torque the cpu to the exact correct pressure for the pins to make contact

@CapComa

10 ай бұрын

@@LinusTechTipsTemporary I don't think that's the issue

The sound clip of Dawid installing the 16 ram sticks is my new ringtone 😊

Curious about the PSU you used. I know some server grade hardware is pretty finicky about power.

If this was run in a server, you might need to set up a console via the management port and tell it to turn on. It could be that it's just waiting for the command to start up. Turning on a server board just starts to initialise the management subsystem, think of it as turning on the computer that will turn on the computer.

Seems like torx bit that you used for tightening down CPU to the socket, was little to big. Might be that you didn't tighten those three torx screws enough.

Funny how I for years have made builds from trash picked hardware literally, I can't see a PC next to a trash bin without having to open it and check out what's in it! So watching your channel is strangely satisfying. Guess making a youtube channel is kind of brilliant. Thank you for letting me know I'm not the only weirdo out there.

Always enjoy watching you struggle 😂🍻

5:23 not enough thermal paste, that is ~50% of what you really need.

Didn't realise supermicro did mini-SAS connectors directly on the board, I might actually look at getting a supermicro board (probably not epyc based tho lol) for a home server setup. Great vid :)!

"once I see that not working" lolol Don't give up!

Love the video, a few months might be a bit hopeful unless you have Wendell or Linus's number handy. Good luck and i can't wait for the update video 🙏🙏🙏

cant wait for part 2.

I wish I could get my hands on those server components for that price. What a bargain (assuming you will get it to work). Those are amazing for virtualization. We have one of those at work and they kicked the living crap out of the old xeons we had before. So good luck to you getting them running! And if you do, enjoy this great system!

A few things as well. Not all epyc chips will work on all boards. You need to verify that chip works on that motherboard. There were what 3/4 gens on that socket? So thats what i would check first.

i’ve used ebay a total of 4 times in my entire life & i’ve legitimately been happy with it once. i’m actually shocked & equally impressed it’s managed to survive so long

We're gonna need to call in backup from Wendell

6 days later: Dawid turns into a Wookiee. Dawdacca Does Tech Stuff, let's goooooo!

4:06 bro was really amazed a screwdriver set had torx bits

Dawid, you are the best! Thanks for a laugh 😂

Those CPUs are not even suspiciously cheap actually, just a little while back I sold 2 of them BNIB for $130 or 140 each iirc (USD).

this man is doing the things I need tto see