I set up, tune and review the new 2020 Hoyt RX-4 Ultra Compound Bow.
Жүктеу.....
Пікірлер: 37
@CAB754 жыл бұрын
Best video I’ve seen on why to bare shaft tune. Great video
@travisglassman
3 жыл бұрын
Thanks 👍
@dangold1998 Жыл бұрын
Great video!!
@travisglassman
Жыл бұрын
Thank you!
@dlswot89504 жыл бұрын
Excellent video
@travisglassman
6 ай бұрын
Thx
@northwestarrowz39844 жыл бұрын
Hoyt baby!!! 🎯
@travisglassman
6 ай бұрын
🙌🏻
@KonstantinMazila3 жыл бұрын
super video, you are great !!!!!!!!!!
@travisglassman
3 жыл бұрын
Thank you very much!
@BramX104 жыл бұрын
Great video, what kind of Stabilizers do you have on there? Brand and Length? What do you recommend and why?
@travisglassman
3 жыл бұрын
I use the Stokerized Stasis 15”. I love the adjustability. You can adjust the position front to back, add weight to front to back etc.
@joeljohnrempillo53594 жыл бұрын
I got the same exact bow setup! RX-4 ultra, QAD integrate MX ultrarest, and CBE engage sights. It's a great bow. What stabilizer set do you recommend for this?
@travisglassman
3 жыл бұрын
Stokerized Stasis 15”.
@lukemaske25354 жыл бұрын
What type of organizer is that when you’re in the garage at the beginning of the video? I’m needing an organizer for all my stuff.
@travisglassman
3 жыл бұрын
It’s an old shelf that goes behind the seat of a regular cab pickup. I just mounted it to the wall.
@AERIALASSAULT13 жыл бұрын
I'm trying to learn all this. This is by far the best tuning video i've watched. But just to clarify on twisting the cables on the yokes. You put 2-2.5 twist in the left cable only. That got you to shooting perfect. Then to re-sync the cams you just take 2 twist out the right side? Or add 2 additional to the left and take 2 out the right. You kinda confused me how you worded that at the 24min mark
@travisglassman
3 жыл бұрын
Thank you for the comment. Ideally, a person definitely wants to make the opposite adjustment to the opposite cable. For instance, if you put a twist in the left, do you want to take a twist out of the right in order to keep the same cam synchronization. You’re right, I did not explain that very well and I’ve learned a little more since the video. Also, you can always make an adjustment to the bottom side of the same cable to get your cam synchronization back in line.
@bdakin912 жыл бұрын
Travis can you tell me where you got the red bow "vise". Did you make it? Good video. Thanks
@travisglassman
2 жыл бұрын
It’s a very simply built homemade vice.
@jasoncorcoran4 жыл бұрын
Will you be doing a more detailed video on the arrow rest setup / tuning ? Got same bow and rest last week myself . Arrow rest setup is still causing some issues. Really enjoyed this video . Thank you .
@travisglassman
4 жыл бұрын
Ja Corkie I basically covered the rest setup/adjustments I recommended. They are very minimal. Simply set it up so the arrow and string are perfectly at 90 degrees. Then move the left/right adjustment to align with the center of the riser/grip. If bare shafts aren’t flying with your fletched arrows, you’ll need to adjust your yoke cables/cam lean to get everything square. I can help if needed.
@bettscr
4 жыл бұрын
@@travisglassman on my new RX-4 Alpha, the axial to axial is not exactly what it should be, its about 1/8" off much like yours was at first. The more concerning part and my question for you is, the axial to axial is not the same on both sides of the bow. I hope that makes sense, but should that be step 1, to get the avail to axial the same on both sides of the bow and then correct the overall axial to axial?
@travisglassman
4 жыл бұрын
@@bettscr the axle to axle may be slightly different on each side due to the cam lean or tiller adjustment I speak about in the video. This allows for a better bare shaft or broadhead tune with the rest in a desirable position in the center of the riser. To change the axle to axle length, you'll need to add or remove twists from the string itself. Check out this video kzread.info/dash/bejne/gXhtpdemgbm8qNo.html
@bettscr
4 жыл бұрын
Travis Glassman Thanks for the quick responses, much appreciated.
@jhuntley575
4 жыл бұрын
Get set up on AT watch KZread if you want to learn. When I got into archery I decided I needed to become a tuning wizard which took me about a year to get decent at. Getting all the tools were an investment. It's the best way to go to do your own work so your not constantly worried about making it to the shop for this or that. Waiting in lines, and honestly they wont do more than the basic tune. Good luck
@Steve-ce1mh2 жыл бұрын
How do you have your vanes fletched? Straight, offset, helical? Right or left?
@travisglassman
2 жыл бұрын
Right helical. I use an Arizona ez fletch tool Mini Max tool
@bettscr4 жыл бұрын
Your number 2 cams get you up to a 30" draw?
@travisglassman
4 жыл бұрын
Yes.
@reddawng43x91 Жыл бұрын
Did u also untwist the right side? If not you better check all ur specs
Пікірлер: 37
Best video I’ve seen on why to bare shaft tune. Great video
@travisglassman
3 жыл бұрын
Thanks 👍
Great video!!
@travisglassman
Жыл бұрын
Thank you!
Excellent video
@travisglassman
6 ай бұрын
Thx
Hoyt baby!!! 🎯
@travisglassman
6 ай бұрын
🙌🏻
super video, you are great !!!!!!!!!!
@travisglassman
3 жыл бұрын
Thank you very much!
Great video, what kind of Stabilizers do you have on there? Brand and Length? What do you recommend and why?
@travisglassman
3 жыл бұрын
I use the Stokerized Stasis 15”. I love the adjustability. You can adjust the position front to back, add weight to front to back etc.
I got the same exact bow setup! RX-4 ultra, QAD integrate MX ultrarest, and CBE engage sights. It's a great bow. What stabilizer set do you recommend for this?
@travisglassman
3 жыл бұрын
Stokerized Stasis 15”.
What type of organizer is that when you’re in the garage at the beginning of the video? I’m needing an organizer for all my stuff.
@travisglassman
3 жыл бұрын
It’s an old shelf that goes behind the seat of a regular cab pickup. I just mounted it to the wall.
I'm trying to learn all this. This is by far the best tuning video i've watched. But just to clarify on twisting the cables on the yokes. You put 2-2.5 twist in the left cable only. That got you to shooting perfect. Then to re-sync the cams you just take 2 twist out the right side? Or add 2 additional to the left and take 2 out the right. You kinda confused me how you worded that at the 24min mark
@travisglassman
3 жыл бұрын
Thank you for the comment. Ideally, a person definitely wants to make the opposite adjustment to the opposite cable. For instance, if you put a twist in the left, do you want to take a twist out of the right in order to keep the same cam synchronization. You’re right, I did not explain that very well and I’ve learned a little more since the video. Also, you can always make an adjustment to the bottom side of the same cable to get your cam synchronization back in line.
Travis can you tell me where you got the red bow "vise". Did you make it? Good video. Thanks
@travisglassman
2 жыл бұрын
It’s a very simply built homemade vice.
Will you be doing a more detailed video on the arrow rest setup / tuning ? Got same bow and rest last week myself . Arrow rest setup is still causing some issues. Really enjoyed this video . Thank you .
@travisglassman
4 жыл бұрын
Ja Corkie I basically covered the rest setup/adjustments I recommended. They are very minimal. Simply set it up so the arrow and string are perfectly at 90 degrees. Then move the left/right adjustment to align with the center of the riser/grip. If bare shafts aren’t flying with your fletched arrows, you’ll need to adjust your yoke cables/cam lean to get everything square. I can help if needed.
@bettscr
4 жыл бұрын
@@travisglassman on my new RX-4 Alpha, the axial to axial is not exactly what it should be, its about 1/8" off much like yours was at first. The more concerning part and my question for you is, the axial to axial is not the same on both sides of the bow. I hope that makes sense, but should that be step 1, to get the avail to axial the same on both sides of the bow and then correct the overall axial to axial?
@travisglassman
4 жыл бұрын
@@bettscr the axle to axle may be slightly different on each side due to the cam lean or tiller adjustment I speak about in the video. This allows for a better bare shaft or broadhead tune with the rest in a desirable position in the center of the riser. To change the axle to axle length, you'll need to add or remove twists from the string itself. Check out this video kzread.info/dash/bejne/gXhtpdemgbm8qNo.html
@bettscr
4 жыл бұрын
Travis Glassman Thanks for the quick responses, much appreciated.
@jhuntley575
4 жыл бұрын
Get set up on AT watch KZread if you want to learn. When I got into archery I decided I needed to become a tuning wizard which took me about a year to get decent at. Getting all the tools were an investment. It's the best way to go to do your own work so your not constantly worried about making it to the shop for this or that. Waiting in lines, and honestly they wont do more than the basic tune. Good luck
How do you have your vanes fletched? Straight, offset, helical? Right or left?
@travisglassman
2 жыл бұрын
Right helical. I use an Arizona ez fletch tool Mini Max tool
Your number 2 cams get you up to a 30" draw?
@travisglassman
4 жыл бұрын
Yes.
Did u also untwist the right side? If not you better check all ur specs
@travisglassman
Жыл бұрын
Done.
Check ur ata now!
@travisglassman
Жыл бұрын
Got it under control
I never bare shaft tune; never will.
@reddawng43x91
Жыл бұрын
Lol
@travisglassman
6 ай бұрын
10-4