How to Use a Diamond Core Drill - The Secret To Making Big Holes
Тәжірибелік нұсқаулар және стиль
Today i will be showing you how to use a diamond core drill bit and how you can make a big hole in a wall. Common jobs such as tumble dryer ducts and bathroom extractor fan installations all require this method. I will be showing you the tips and tricks that make the job easy! If you like the content leave a like and please subscribe for more content like this as I've got a lot more to come and there will be something that will help you out.
⚪ Buy The Tools Needed Below
🌟 Diamond Core Bit Set - amzn.to/43ecVmC
🌟 SDS Drill - amzn.to/3ZOnZEr
🌟 Tracer Pencil - amzn.to/3WVwdJG
🛒 My Shop -www.amazon.co.uk/shop/thediyguy
► BECOME A MEMBER OF THE DIY CLUB Click! 👇🏼
/ thediyguy1
► Get FULL access to the Discord Group and other perks!
Follow me on Instagram 👉 the_diy_guy_youtube
Thanks for watching The DIY Guy. My mission is to bring you the best Tips, Tutorials and Tools to help you learn and save money.
Please be advised that this is only a guide which is intended for informational, educational and entertainment purposes and The DIY Guy cannot accept responsibility for any work undertaken. Be safe and have fun! The Amazon links above are affiliate links and as an Amazon Associate I earn from qualifying purchases. I may earn a small commission if you purchase via the recommended links, however this will not cost you any extra.
Пікірлер: 371
One little tip that I use to ensure you don't get plaster blow out on the inside is to use the core bit on the inside to just cut through that first half inch or so of plaster. Then move to the outside to cut the hole. The pilot hole will ensure that the two cuts line up perfectly, and as you have already cut through the plaster on the inside you don't get it blowing out as the core goes through. Sure, it does make a little dust on the inside but worth it to keep the plaster in one piece. 👍🏼
@TheDIYGuy1
Жыл бұрын
Thanks for sharing 😀
@alemgas
Жыл бұрын
In your dreams mate
@thechumpsbeendumped.7797
Жыл бұрын
@@alemgas What is in his dreams?
@cuebj
9 ай бұрын
For pros, Makita do a dust extraction accessory for their diamond core drills - very expensive and heavy duty. As heavy duty DiYer, I do what you do
@Nine-Signs
7 ай бұрын
@@cuebj Potential cheaper solution? Henry + bag. Henry likes to eat all things, and rolls down stairs well, and are still pretty cheap. Mines 25yrs old and for the last 7 has been sucking up everything from masses of brick dust to lose cold ashes around the fire. Remarkable machines, especially the older ones.
You sir are a Godsend. Instructions clear and concise. That is a job I have dreaded but you have given me the confidence to do it myself. Many thanks.
Great video, I did an extractor fan recently using these bits 👍🏻
Top tips as usual, and I love how clean your safety goggles always are! Look forward to the renovations👍
@TheDIYGuy1
Жыл бұрын
Thanks. Those are new ones sent to me from Unilite. Great glasses so far.
@bobbymac2911
4 ай бұрын
@@TheDIYGuy1 Now do hearing protection and a dust mask. Wear all your PPE and set a good example
Excellent presentation as always!
@TheDIYGuy1
Жыл бұрын
Glad you like the video 👍
Thank you very much Your videos is very good Everything is well explained Please do more videos like this 👍
Excellent video. Thank you.
Great tip about running the pilot bit all the way through and core drilling back in from the outside. Wish I had thought of that doing all my room vents 🤣🤣
@TheDIYGuy1
Жыл бұрын
Glad to help!
Excellent video and edit. look forward to the renovation series.
@TheDIYGuy1
Жыл бұрын
Thanks. I’m working on it. Currently I’m working on the edit for episode 1
Nice work, thankyou ..well done.
As always a great informative video 👍🙏
@TheDIYGuy1
Жыл бұрын
Cheers bud 😀
Someone below mentioned it, kickback control, but didn’t quite get to the optimal solution. Left or Right there is always a drill-handle orientation that will let you catch the kickback, which is the only way the clutch will ever engage. For the hole here, rotate the whole drill clockwise 90, then release the handle and rotate that another 90 so it is pointing straight up. Now you can engage the drill with your right hand and the handle is such that kickback with be straight into your palm, allowing the clutch to trigger rather than having it rip away from your hand. Nice video!
Great tip on the pilot drill
Brilliant tip on drilling from inside to out first!
@TheDIYGuy1
Жыл бұрын
Glad it was helpful!
Great video i am drilling through a wall this week for extractor fan great tip drill out pilot hole first from inside and then drill from outside due to dust 👍👏
@TheDIYGuy1
Жыл бұрын
Glad it was a help
Great advice, and great Norfolk accent......"wull done bore keep on a troshin" 👍
I've saved a few quid having a go myself, which I didn't really have the confidence to do before watching videos like this. Nice one DIY guy, keep them coming!
@TheDIYGuy1
7 ай бұрын
Glad I could help! Thanks!
Great video! Thank bro, wish you good health and success always!
@TheDIYGuy1
Жыл бұрын
Thanks a lot you too 👍
@dailytricks6161
Жыл бұрын
@@TheDIYGuy1 have nice day! bro
Experience is the best teacher You're great
@TheDIYGuy1
Жыл бұрын
Glad to have helped. Thanks
Great video !!!!! Looking forward tothe new series .........thanks 😊😊😊😊😊
@TheDIYGuy1
Жыл бұрын
Thanks. Soon, I’m working on the final edit for episode 1 😀
It’s a good idea to put a slight rise, (out to in) on the hole, not level when to be used for vapour exhaust. Any moisture left in the ducting when machine stops will drain to the outside of the wall.
@TheDIYGuy1
Жыл бұрын
Nice tip, not something I’ve ever done.
@matthewsaunby9056
Жыл бұрын
Came here to say the same thing. Probably precautionary more than anything but it can’t hurt!
@paulchatterton1
Жыл бұрын
Absolutely! Very important that condensation finds its way out and not in!
@gaurasrspublishing
9 ай бұрын
But then if you're drilling through for something like a humidistat, the fan doesn't sit flush to the wall because the hole is on the wonk.
Beautiful job
@TheDIYGuy1
9 ай бұрын
Thank you! Cheers!
Awesome job 👍🏼
You forgot the dust mask.but also a question do those bits differ, like for dry cutting and wet.applying water
Lovely video mate
Very helpful video Thankiyou so much very appreciate your help.
@TheDIYGuy1
7 ай бұрын
Glad it was helpful!
Great Job!!
When I was drilling through some really dense comcrete using a 4.5” bit, it helped a lot to chisel away the inside core every inch or so
This is a very helpful video!
@TheDIYGuy1
9 ай бұрын
Glad you think so!
may as well get a condensing dryer as in a couple years we will see another video of you bricking it back up.
@TheDIYGuy1
Жыл бұрын
I’ve an old boiler flue hole to brick up if it’s something you want to see 😂
great video thanks
@TheDIYGuy1
Жыл бұрын
Glad you enjoyed it
Thank soo much freind, i appreciate a lot your advices, i lear lot of things from you , thank again , good luck for futur videos
Great video as always, what would be great to see is what sealants to use for what’s going in the hole!
@gregarrell6132
Жыл бұрын
Some dust control and lung protection is essential. Vacuum and P2 respirator.
first time here .very informative will be looking out for more of your videos.
@TheDIYGuy1
Жыл бұрын
Awesome, thank you!
I can tell you from experience that the core bit / drive shaft you are using will bind together after heavy use. It is then virtually impossible to separate the shaft from the bit and that means you cannot change bits thereafter. Before use I would recommend making and breaking the shaft/bit joint and also using copper grease or similar to make subsequent release of the joint more likely. I was drilling foundation wall that consisted of heavy-duty concrete blocks laid on their sides. The second point I would make is that the stub shaft being used will not get you through such long traverses. Eastablish whether you need a shaft extension before committing to task as separate purchase of long shaft is expensive. If these extensions binds and won’t release you will have an even greater problem to solve. I eventually resorted to stitch drilling after first creating the first short penetration using diamond core. That worked well and was faster but not a neat finish on the exit side of the hole.
Great and good quality video again . 👍 👌
@TheDIYGuy1
Жыл бұрын
Thank you 👍
@marcelobadilla5825
Жыл бұрын
The detector can find the cavity wall ties? Just to avoid drill over a wall tie 😮
You can avoid any brake out on the inside by drilling a little that side first.
@TheDIYGuy1
Жыл бұрын
That’s certainly another option 👍
Great job and great video thanks for sharing with us this appreciations 🇩🇰🙏👍
good work ! top video !
@TheDIYGuy1
Жыл бұрын
Thank you very much!
Your presentation skills are getting better and better. Much more natural these days. Good vid, ta.
@TheDIYGuy1
Жыл бұрын
Much appreciated!👍
Great video...👍🏿👍🏿👍🏿👍🏿
@TheDIYGuy1
4 ай бұрын
Thanks 👍
Core blimey!!! Cracking video 👍🏿👍🏿hole in one ⛳⛳⛳
@paul_my_plumbs_uk
Жыл бұрын
Instagram top tip copper washers on the chuck adapter
@TheDIYGuy1
Жыл бұрын
Thanks 😊
Good tips
Thanks again for all the advice you give, i always make sure I never miss a video.
@TheDIYGuy1
Жыл бұрын
I appreciate that!
Great video! How would you go about enlarging an existing hole to fit a cooker hood that needs a bigger hole?
Good explanation! A little advice: in the future, try to move the handle in 90 degrees to right or left. In case of stuck or something you will control the drill much easier Good luck!
Great video. One thing I'd point out in my case - even if it means some vertical ducting inside stay well clear of the DPC. My house sits on a plinth of some sort and if you hit that your hole stops there. Got lucky, but it was close!
@chipburns4123
Жыл бұрын
DPC? Democratic Political Cheat?
@cuebj
9 ай бұрын
Good point. I have exactly that: rectangular duct between wall and dryer, rectangular to round connector to duct in wall. Unexpected benefit is it's more flexible when I've changed position and brand of dryer - just shorten or lengthen the flat duct and change angle from dryer vent to wall vent
Informative video. Wondering if this would work with the Hilti TE 50-AVR.
Do you have an idea on how to drill onto uneven surfaces? For example: rocks on the beach area? The goal is to build and plant a metal post onto it.
Very nice
@TheDIYGuy1
Жыл бұрын
Thanks
Good video!
@TheDIYGuy1
7 ай бұрын
Thanks!
great video - any tips to stop core sticking to abour - tried copper grease already thanks
I was pleased to see you mentioned to put drill on drill only and not hammer! I really wish you would set example and were more ppe your setting yourself up for future I’ll health
Your new home? Congrats
Oh how I wish I had one of these, instead it was a bolster and hammer job after drilling a grid of holes then mortar in after. The fun.
Perfect video! In Sweden we often use 125mm vent ducts. What dimension do you recommend for the hole?
I've been prevaricating on this one for my cooker hood for months, I'm sure I'll brave up enough to do it eventually - my complexity is timber framed house so i got moisture barrier to deal with also; though I also have only one layer of brick to deal with so swings and roundabouts.
@cuebj
9 ай бұрын
Hole saw or pad saw for the timber and plasterboard. The single thickness brick could be done with lots of holes using 6mm or 8mm SDS bit; then tap with small cold chisel. If you do hire or borrow diamond core gear, practice on a paving slab or block. Get very comfortable and solid in your stance for holding the tool and moving it through a position that mimics the hole you want to make - can you hold it without dropping from your line?
If you are drilling through something a bit tougher and maybe using a long extension, try drilling 4 holes at the top, bottom, left and right outer parts of the hole you are trying to cut. This makes the core bit easier to drill through the wall as it hasn’t got as much friction due to the holes. I’ve done this many times, it makes it a lot quicker and easier particularly if you are in a tight spot. Try it out.
spraying water occasionally, helps with dust and provide some cooling to the the core drill.
Easy 👍 please do pebble dash concrete next 😂😂😂
I have the same set of Erbauer drills. It is a bargain buy. If you purchase the 3 core drills and the mandrels separately it would cost double what you pay for this and you wouldn't even get the case. I have a 117 core to drill tomorrow in the loft. fortunately it's a double skin of breeze block with render on the out side so it won't take long. I drill the outside render first then drill the last inch from the inside to avoid blowout.
great video what min wattage drill to use?
you rock!
@TheDIYGuy1
26 күн бұрын
Thanks 🤟
I cut and drill concrete for a living and I’ve broken my wrist with a 8” bit lol but was also using a hilti hand drill
Hello mate whats the best length sds bit for this? I bought 400mm but think 600mm willl be better
I really enjoyed the way you explained it. Smart and clean. Only for safety put on a mask too beside the safety glasses. For protecting of all that dust entering to your lungs. If you do this on daily basis it can lead to nasty lung diseases.
Nice! I wonder if these can drill through sandstone and granite rock.
6:45 Forgot the glasses again ;). Nice video, thanks!
to reduce the blow out on the inside even more I usually run the coredrill in 5-10mm before going outside
@TheDIYGuy1
Жыл бұрын
Thanks for sharing 👍
how well does this work in fiberglass reinforced concrete and what happens if you run into rebar?
Would you recommend going from outside then doing the inner wall from inside out over if you had pipes and cables nearby?
Is this the right saw bit to cut through stucco, too?
For the pilot hole bit (8 mm) does that bit need to be diamond tip also? Or can I use the pilot bit that comes with the core bit to drill the pilot hole?
Can you give any tips for enlagering a previous hole?
What is a recommended hand drill machine? I am asking about lowest watt machine required for a hole saw bit to drilling in properly?
Secondary pro tip if dust/debris mitigation is a concern. Bosch (and other tools brands) makes a suction cup attachment to the shop vac that, when the vacuum is activated, suctions it to the wall. You put your drill or core but through the center of the bristle attachment and all dust and debris get sucked out as you go. Saves a huge mess and minutes of clean up afterwards. This also saves you from wearing a respirator, which you should be for any masonry drilling application. Silica and mortar dust is incredibly harmful to human lungs.
@TheDIYGuy1
9 ай бұрын
👍
I have a guild 1000w sds is this powerful enough?
Where can I get the complete set of this diamond core bits and the drill set
Have you got a video where you make a Review on HP2071? 🤔 Would like to see how good it is.
Always use the correct core drill with a clutch so save broken arms and wrists,i would not recommend use a standard drill for this type of job !
@michaelshaw8656
Жыл бұрын
It was a clutched drill 👍
@prawnk1ng
Жыл бұрын
Exactly. The clue is in the name. Core drill for a core bit. SDS could land you a trip to A&E
@ddfann
Жыл бұрын
I uses an SDS to core drill all the time, it has a clutch and has never kicked back at me.
@sydsnott5042
Жыл бұрын
Ok that's acceptable what you've stated But I did just that job some years back with a standard hammer drill. Yes I got got some slight kickback but I got the job done without any broken bones or bruises. Yes I took my time.
@darrenpaulgreen
Жыл бұрын
Young guy I was working with drilled a core hole using a standard SDS. Drill kicked back and he tore his rotator cuff in his shoulder. A month off work and it’s at least 5 years ago now and never been right since 😖. Core drill for a core drill bit every time.
Any advice for an overscrewed bit that won’t unscrew??
I'm looking for an SDS drill that can drill big holes. The SDS drill you link to is actually the one I was thinking of getting but everyone says it's not going to be able to cope with core bits over about 20mm and I need a corded drill for anything over this. I notice you use a corded drill in this video, what's my best bet for site and domestic work as I don't really want to have to buy two for the different power ratings? Cheers.
👍👍👍Thanks
@TheDIYGuy1
Жыл бұрын
Welcome 👍
Was going to say goggles, but also ear plugs and dust mask. Nice job though 😊
@TheDIYGuy1
Жыл бұрын
Haha yeah probably best. Cheers
Are drainage pipes cut level also? Or do you need to cut them at the same angle the pipes need to drain? Is that easier than it sounds?
I can't find the arbor adapter for sale anywhere for a regular hammer drill.
Worth greasing, or anti-sieze paste on threads
I have2 concrete wall and 5 feet gap it’s between them how can I make that any idea?
Before i screw the diamond core to the arbour i put some 20mm electrical lock nuts on the arbour that way the core cutter can never wind up tight on the arbour thread and easy to remove.
Pro tip, have a healthy breakfast before you start 😄
Can a Milwaukee 1" 9/16 rotary hammer be used with a core bit to drill through concrete?
The shank type is this SDS Max? Cannot believe it would be a SDS plus.
Once your pilot hole is drilled bit of painters tape on the inside and Gorilla tape on the exterior brick really helps lessen blow out or cracks.
@TheDIYGuy1
4 ай бұрын
👍
Corbett? Need Barker, too. Good tips, which we used a few years ago. For the more casual DiYer, this is a case where hiring the gear makes sense as you might just do it once. The Erbauer kit is pretty good, even for pro tradespeople who don't do this all the time. If it's a tiled wall, use a tile grinder to remove tiles with about 5mm extra radius and cut hole a few inches deep from the tile side first, then cut from the outside. The pilot hole ensures the two holes meet up. You might have to hack insulation from the cavity as the bit gets clogged
@TheDIYGuy1
Жыл бұрын
👍 cheers and thanks for sharing
If you go up on the ladder, make sure someone holding the ladder for you, and even changing turns! You can get tired quickly higher on the ground holding heavy drill and it will feel more heavier!
My OCD loves the brand new core drill, nice and clean. Dont really want to use it and chip the paint off and get it dirty😂
@TheDIYGuy1
7 ай бұрын
😂
How to avoid wall ties? Are these picked up by the detector?
Great video, but may I suggest in the recommendation for a drill that you specifically mention a clutch. If somebody tried without one, they might end up with an unpleasant experience.
@TheDIYGuy1
4 ай бұрын
👍
Dust aside - if kick back is most likely going into the internal wall from cavity. Would it not make more sense at this point to drill inside outwards? Some does but avoids kickback and also blow out risk?
My sds drill (dewalt) clutch is not man enough for 4" core drill spend more time trying to get it to bite. I think I need a proper core drill.