Thanks for watching! Remember if your not 3.4 swapped like me you dont need to do the 10ohm resistor mod.

Thanks for your time and info!!!!

Good shit , I’ll come back to this.

Awesome. Love that your truck has a red interior too. Mine is a 90 4x4 22RE metallic red on red. Red interiors on these trucks apparently pretty rare

@DirtGarage

3 жыл бұрын

I LOVE the red interior.

So how would hook up the tach on my 4.3 chevy swap 91 sr5 pickup? Advanced adapters has a pretty thorough guide for the major aspects of this swap but they leave out some of the finer details. When talking about the tach they just say "when swapping a gm v6 your tach should work without modifications" but that doesn't tell me how to hook it up! Haha

What’s up I have a 94 Toyota with a dual coil 3rz swap. just swapped a sr5 cluster in and I don’t know where to run the tach wire to my motor. Thanks

glazed right over how you unhooked the speedo cable from the rear of the cluster !

hello, I have a toyota 22re pickup, I changed the cluster for a toyota v6 3.0 upgrade, my question is the following since this cluster has a speedometer cable and mine is electric what to do when the speed gauge does not work

I just about got my 3.4 swap complete, I would like to install that same oil sending unit, before I put the motor back in. I'm swapping clusters just like your video. Is that a 3.0 sending unit?

Can I tap into that black wire to install an aftermarket tach? Or does it only work if I use another oem gauge cluster?

Hey man I have 89 I am about to swap out the gauge cluster and I am not sure if my truck was pre wired for the tach however previous owner put in an after market tach and oil pressure gauge. But not sure if I need to do the ten ohm like you had to with your truck...

Hello friend, a pleasure to greet you from Honduras. I tell you that we have carried out the project to change the engine of a 1995 4runner with 3vz to a 5vz 3.4 almost everything goes well but when assembling the tachometer it does not mark the revolutions because we have not connected the wiring for it, with these indications it should work the revolutions?

Hola me puedes ayudar tengo un 22r modeló 93 sencillo extracab pero la aguja del reloj de presión de aceite no sube y ya le puse tres bulbos que sera

I have a question if anyone can give me insight. I did this cluster swap I got mine out of a 1994 T100 yes they fit the 92-94 pickups as long as it’s electric they have cable driven one too but anyways. With the original stock cluster temperature would stay really low id move about a few inches from the cold line. After the cluster swap the temp gauge goes half way.

So I just did a 2rz swap in my 86 4Runner and ordered a “ gauge” style sender but my oil gauge gos up to 3/4 just turning my key on and stays there 😊

Will this work for 4 cylinder, RE engine?

Wow man, your channel is AMAZING. I am going to be eating up a lot of these videos. This gave me a great starting point for my cluster swap for my '93 T100. I am, however, a bit lost about things like that digital display you have. Also, I saw in another video that you somehow got OBD2 into this truck and I am just missing so much contextual knowledge on all of that. Can you suggest any resources for learning about things like that?!?!

@DirtGarage

10 ай бұрын

My truck at this point had a newer motor, and used a newer ECU. The newer motor used a OBD2 diagnostic port. Older motors like in your 3.0 93 T100 does not have a option to use OBD2

@TheSamsonizzle

10 ай бұрын

@@DirtGarage Ah ha! That clears it all up. Thanks for the fast reply!

Do you keep track of the mileage manually then? Bookmarked for my future swap. Great vids.

@DirtGarage

4 жыл бұрын

I actually adjusted the mileage to match mine. Did not include in this video. But possibly will on a future video.

Hey man I just bought a 1993 pickup with a 3.4l swap but that thing needs a lot of work. Does your shift lever sit towards the left side? Also does your truck shake when you let go of the clutch and its starting to grab?

@DirtGarage

5 жыл бұрын

Hey thanks for the comment! My shift lever is off to the left, but in the normal spot it wants to sit. Also my truck does not have any sort of shake related to the clutch.. Sounds like you got some problems to sort out! Maybe check the trans/engine mounts.

@Jursaw

5 жыл бұрын

Dirt Garage Thanks, my shifter maybe bent because in 5th gear it looks like what 1st gear would be in my other truck that has a 22re in it 4x4. This truck has a body lift on it to clear the 3.4l

I have the 22re engine would the work if i swap the tech from a V6 4runner???

@DirtGarage

5 жыл бұрын

Yes. Your tach signal is from a different spot. But everything else is the same as my video.

disculpa tengo un tablero de 5vz en mi 3rz y las rpm son mas bajas, tendrá alguna solución?

@DirtGarage

2 жыл бұрын

At about 9:15 in this video here I talk about how to adjust your tach: kzread.info/dash/bejne/YmukzY9mf7qpgdY.html

Also I have no lights in the dashboard

will any 10k resister work? or what wattage should i use? 3.0 to 3.4 thanks!

@DirtGarage

5 жыл бұрын

Honestly not 100% sure. I used these ones amzn.to/2QdZAWA And it's working great!

@JesusHernandez-lv4rx

5 жыл бұрын

It has to be a 1/4 watt 10k ohm resistor

Yo tengo un 22re y le pondre el cluster con tacometro. Pero no se de que valor poner la resistencia. Puedes ayudarme con eso

@DirtGarage

5 жыл бұрын

No necesita usar una resistencia si está instalando esto en una 22re. Solo se requiere si va de 3vz a 5vz, o de 22re a 3rz. Si no puedes entender esto, ¡culpa al traductor de Google!

@carloscorrea6479

5 жыл бұрын

Ya pude instalarlo. Y no ocupe modificar nada. Solo conecte el tacometro y cambie la iluminacion que trae por unos hiper leds.

I have a 2wd 22re with a electric speedometer and no tach is it possible to do this swap

@DirtGarage

2 жыл бұрын

Yeah. Same process

Do I need to add the oil presuse sensor in a Toyota pick up 91? I just got a cluster like yours. Thanks in advance.

@matexf4c

Жыл бұрын

If it comes with the simple tach with just the speed temp and fuel then yes. I have a question is it a 22re or a 3.0

@bigpilouh7256

Жыл бұрын

@@matexf4c Its a 22RE engine. The only problem is that I couldnt get the tach to work

@matexf4c

11 ай бұрын

@@bigpilouh7256 I thought I replied my bad but there’s a video by a Chanel called garage build Hondas he has a link that shows you where you have to solder on the rpm cluster

@bigpilouh7256

10 ай бұрын

@@matexf4c I saw that video. But if I didnt undertand wrong the resitor only applies whe the swap is from 8cly to 6cly; am I right? btw thanks for the support

@matexf4c

10 ай бұрын

@@bigpilouh7256 yeah that is correct no need to solder anything. I think I figured out why the rpm aren’t working I finally swapped mine out and got it running I’ll make a video on it right now and post it on my channel so you can see it

Do you have to do the resistor mod for a 3.0 application?

@DirtGarage

3 жыл бұрын

Nope! Just if you have 3.4 swap!

@whiteout628

3 жыл бұрын

@@DirtGarage oh sweet! Thank you!

How come the tach adjustment knob doesn't work for the 3.4 swap?

@DirtGarage

6 ай бұрын

It does

@rdybhjhbehb

5 ай бұрын

Im confused. Whats the benefit of adding the resistor vs adjusting the knob using a secondary tach? @@DirtGarage

I need the link for the gas guage everything works except the gas guage

@DirtGarage

4 жыл бұрын

My gas gauge not working had nothing to do with the cluster swap. My fuel level sending unit failed in tank. When I replaced that it started working perfect.

@owenfalconer9398

4 жыл бұрын

But it was working parshally not giving the correct reading but the needle work now this one nothing but I am going take off the back and check it

@DirtGarage

4 жыл бұрын

@@owenfalconer9398 So I once had a issue where my gas gauge was not working and me temp gauge read waaay higher than normal.. This was caused by a bad ground. Maybe your issue? Or perhaps you picked up a bad cluster?

@owenfalconer9398

4 жыл бұрын

@@DirtGarage well maybe but it's hard to get originally but from the junk yard it's going a $100us

How do you fix the gas guage

@patrickfields3392

4 жыл бұрын

I think his issue was with the sending unit not telling the gauge how much fuel was in the tank. It isn't an issue with the cluster because the fuel gauge is plug and play. His issue is in the tank. A new sending unit would fix that problem.

@DirtGarage

4 жыл бұрын

My issue was the fuel sending unti! as Patrick mentioned. Replaced the sending unit and it was fixed!

@owenfalconer9398

4 жыл бұрын

Am going to try changing the sending unit because mine is the same plug n play so am going to change the sending unit and see

A/c wiring????

@DirtGarage

4 жыл бұрын

Sorry, I can't help you there, no experience yet!

@evanmadigan3157

4 жыл бұрын

@@DirtGarage it's all good I'm bout to sit down and figure it out I'll do a write up and send it