How do u know if it's the rotor position sensor and not the rotor and stator that's bad?

@aaraujo306

8 ай бұрын

Curious too

It's kind of common sense how to take it off and replace it. The important question is how to test it to know it's the problem. What are the voltages or resistance values I need to see to make an informed diagnosis?

@matthewschug939

Жыл бұрын

Speaking as a retired auto mechanic.

@RichaRat

Жыл бұрын

Anybody can throw parts at it. I suppose that is what they want us to do.

@Rockfish21035

6 ай бұрын

Pin 1 (common) to Pins 3 & 4 (Hall sensors 1 & 2) should be resistance of 10-12 K ohms. Pin 2 is ground

I replaced the sensor dc-31-00098A and the machine is still not working. It starts but it doesn’t sound like any water is coming in. The water is on

Will this stop it it from spinning out of control and complete spin cycle?

Nice. Very detailed video. Thank you

Any way to test the sensor?

@alexdavis7872

2 жыл бұрын

Multi meter cuz

@Rockfish21035

6 ай бұрын

Pin 1 (common) to Pins 3 & 4 (Hall sensors 1 & 2) should be resistance of 10-12 K ohms. Pin 2 is ground

Good video very helpful

I am having trouble with the bolt. Mine looks simillat but i dont feel notches and cant get a screw driver in to lock it. Tried at the both without that part but cant get enough leaverage to budge it. Mines doesnt really spin or turn more than an inch.

I have the same stator motor on your video. What should the resistance values be ? I'm getting 11.8, 11.9,11.9.

@snoopyfix2

10 ай бұрын

Did you ever figure it out?

@sdshawn29

10 ай бұрын

@snoopyfix2 No , the motor looked good. I did not want to go down the rabbit hole. Sold the set to a repair guy who said 90% control panel brain for 300 and bought a new LG set, never samsung again.

Thank you so much for this video. My rpm sensor went out which caused the control board to burn up (literally). Swapped out the board and rpm sensor for just over $100 total and with a little elbow grease I am back to being Cinderella.

@appliancepartspros

9 ай бұрын

Glad we were able to help you out. If there is anything we can help you out with in the future please let us know. We will be more than happy to assist you!

@aaraujo306

8 ай бұрын

How did you know that was the cause? Mine is giving a 3e1 error code, it fidgets trying to move with a slight clunk sound, then completely stops.

@Rockfish21035

6 ай бұрын

Your stator windings should be 12 ohms on each of the 3 windings. The Motor Position Sensor (Hall Effect Sensor) has 4 leads: Pin 1 (common) to Pins 3 & 4 (Hall sensors 1 & 2) should be resistance of 10-12 K ohms. Pin 2 is ground

no spin, no code ?? if the position sensor are defect , can i have a no code ? Yes i change vibrating sensor , an 2 electronic module , and all the wire , ??????

Very helpful but how can I be sure it's the sensor? The washer fills and drains, but it buzzes and stalls at the point where the drum should start agitating. I'm not seeing a code. The drum turns freely by hand. So what are the indications that I need this part please?

@appliancepartspros

9 ай бұрын

What is the model number of your appliance? Have you had any recent power outages?

@VideoVictor45

8 ай бұрын

Yes! It's a WF42H5000AW/A2. What part do you think I need?

@appliancepartspros

8 ай бұрын

Have you tried to put your machine into a diagnostics mode to see if any error codes come up on it?

I have a problem in washer samsung WF42H5000AW the error code is tE4, can you help me?

Had a Samsung error e3 code washer stops after wash cycle,,,changed out the position sensor,,,tried it and still no spin,,,,,,what now?

@appliancepartspros

6 жыл бұрын

We'd be happy to help you out with that! We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number to give you accurate advice, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx

Getting 3c2 code on samsung washer

@geofffreeman8226

21 күн бұрын

same here, what was your fix?

i did this much quicker!

@appliancepartspros

9 жыл бұрын

Roblo22334 Awesome, glad the video helped you get the washer fixed!

@Roblo-gz5qp

9 жыл бұрын

i didnt use the video

@Roblo-gz5qp

9 жыл бұрын

Roblo22334 i paused it and went off and did it in 2 secs, i needed to know where to get it.

@appliancepartspros

9 жыл бұрын

Roblo22334 I am glad you seem to have got your appliance fixed!

@Roblo-gz5qp

9 жыл бұрын

Roblo22334 by "it" i meant the part