How to restore your headlights yourself at home with very little cost! Step by step guide how to restore them the CORRECT way!!
Жүктеу.....
Пікірлер: 51
@major73282 жыл бұрын
I tried this today on my 2004 rav4 “shortie”. Worked 100%. Wish I can share the before and after pics. I live in Trim, Ireland. Bought all the stuff I needed at Halfords. Tnx a million!
@georgefifita71314 жыл бұрын
“We’re just gonna sand in circular motions” *proceeds to sand side to side* Great vid;)
@pennyhancock5197
Жыл бұрын
LOL🤣🤣
@falconlips5474
4 ай бұрын
😂😂😂
@reallifestories10776 жыл бұрын
I've watching tons of these videos but always love the outcome! probably a better method than just toothpaste lol
@Arayman3772
4 жыл бұрын
I used 120, grit sandpaper on headlight and have quite a lot of scratches.. any fixes?
@SG-uj8tj
4 жыл бұрын
@@Arayman3772 lol, 120 is rough grit, you need to use around 250 for "deep" cleaning and roughin out the scratches, then work your way up 600-800-1500-2500-5000 to get rid of all scratches.
@Arayman3772
4 жыл бұрын
@@SG-uj8tj thanks mate. I'm going to give that a shot.
@Dinos.Biz.English2 жыл бұрын
love the videos, keep em coming!
@vergecryptocurrency45526 жыл бұрын
Very good. Thanks
@rened99335 жыл бұрын
Very nice! Thanks! Go on!
@David_S19854 жыл бұрын
Any chance of doing a video on how to use blending thinners in aerosol form? U Pol bend 9 for example.
@al-zj2sy6 жыл бұрын
Just found your channel. Good stuff. Subscribed
@Mad4Motors_
6 жыл бұрын
Thanks video coming next week!
@KipacWF5 жыл бұрын
I dont even have a car, but this is so satisfying, reason i subbed :D
@coolamberboardingkennels30996 жыл бұрын
Great channel very informative.. cheers
@Mad4Motors_
6 жыл бұрын
Hey thanks
@kingdavid34575 жыл бұрын
But what If is yellow xo I use a lower grid sand paper or do I use 800 till is dull clear
@tjmone742 жыл бұрын
Thanks for the great videos. I did this to my headlights and used a 2K clear coat. Unfortunately I got bad orange peel. Would you suggest wet sanding and polishing them?
@johnkaimins9998
2 жыл бұрын
Wet sand and polish provided you have applied 3 good coats, otherwise you will sand through the lacquer and expose the plastic again.
@MrSpyruz10 ай бұрын
Would this work on plastic tail lights? Bought an '87 Tercel, and it seems like the tail lights are smoked, a bit too dark and It's hard to see the blinkers' lights.
@thewolfofsa5 жыл бұрын
Good shit!
@ze_german29214 жыл бұрын
Do you think buffing it between sanding it with 2500 and applying the clear would get an even better shine?
@johnkaimins9998
2 жыл бұрын
No.
@dmaher20074 жыл бұрын
Would 2k clear coat be ok to use on the lights? Great video as always. Cheers.
@johnkaimins9998
2 жыл бұрын
According to my research 2k clearcoat is the ONLY product to use!
@hobo1704
5 ай бұрын
It's the only way it should be done. Polishing is a waste of time..
@stephenho6336 жыл бұрын
That looks great. Please tell me for how long the clear paint can last? I sent my car to have the headlamps made clear but it last for just a month.
@zaink7037
5 жыл бұрын
I would of thought they last longer. Did they use UV resistant clear coat or a good coat of it? Something a guy told me in my local detailing shop is to use a ceramic coating over the headlights. Would last several months to 1-2 years
@ciensuk4 жыл бұрын
Is it made from plastic or glass? Can do this method on both media?
@johnkaimins9998
2 жыл бұрын
This method is only for plastic. Glass does not fade or discolour because it is ...... glass.
@teriorlando7094 жыл бұрын
I wish you were my neighbor, I could use you at my farm... :) Great job!
@gioolioplus
3 жыл бұрын
Use tools, not people
@ej76876 жыл бұрын
Ok I got thr 800 grit sand paper but what was the other one? Also how long would you say the clear coat should last? Also thanks alot for your videos brother I'm learning alot!
@mckeon1960
4 жыл бұрын
800 and 2500, should last the life of the car if you don't the clear coat uv paint says it all in video
@D-zuno Жыл бұрын
Any suggestions on how to deal with condensation on headlights?
@Jackleeds206
Жыл бұрын
drill a small hole in the corner to ventilate
@FuriousHondaBoy2 жыл бұрын
What is conditions of headlights right now ?
@alexrebelrebel6 жыл бұрын
Can I light polish it after it's well dry? Cause it's looks a bit matte...
@Mad4Motors_
6 жыл бұрын
maybe give it a little sand and re clear
@alexrebelrebel
6 жыл бұрын
Mad4Motors Thanx! Great videos!
@johnkaimins9998
2 жыл бұрын
@@Mad4Motors_ Extra coats must be applied within 30 -60 minutes to ensure the coat bonds to the previous coat.
@hobo1704
5 ай бұрын
Use 2k clear..
@dejodevasia77114 жыл бұрын
3:27... 144p to 720p!
@jakeantony84474 жыл бұрын
Just gonna start sanding in circular motions.... Sands backwards and forwards That made laugh more than necessary
@FEDANIK215 жыл бұрын
🙈🙈🙈
@JayLupe4 жыл бұрын
I tried this but got cracks thru my clear coat, HELP!
@johnkaimins9998
2 жыл бұрын
You must sand back to the plastic again. Thorough prep is ESSENTIAL. If you can, remove the headlight from the vehicle to ensure thorough cleaning around the edges of the headlight. Final sanding grit is 1000. Using a finer grit risks the clear coat not sticking to the plastic. THOROUGHLY clean the head light with isopropyl alcohol using a lint free cloth to remove ALL traces of waxes and contaminants. Apply the first coat lightly, then 2 good coats 20 minutes apart. This is easier if you have the headlight removed because you can lay it flat to reduce the risk of runs. Wait 30 days before polishing/ sealing with wax, otherwise you prevent the solvents in the clear coat from "out gassing" trapping them under the wax. Good luck.
@NC-ro5gw3 жыл бұрын
You should of swapped out the acrylic lacquer for battery acid.
@colmbrady42453 жыл бұрын
use t cut it does the same job but with half the work
Пікірлер: 51
I tried this today on my 2004 rav4 “shortie”. Worked 100%. Wish I can share the before and after pics. I live in Trim, Ireland. Bought all the stuff I needed at Halfords. Tnx a million!
“We’re just gonna sand in circular motions” *proceeds to sand side to side* Great vid;)
@pennyhancock5197
Жыл бұрын
LOL🤣🤣
@falconlips5474
4 ай бұрын
😂😂😂
I've watching tons of these videos but always love the outcome! probably a better method than just toothpaste lol
@Arayman3772
4 жыл бұрын
I used 120, grit sandpaper on headlight and have quite a lot of scratches.. any fixes?
@SG-uj8tj
4 жыл бұрын
@@Arayman3772 lol, 120 is rough grit, you need to use around 250 for "deep" cleaning and roughin out the scratches, then work your way up 600-800-1500-2500-5000 to get rid of all scratches.
@Arayman3772
4 жыл бұрын
@@SG-uj8tj thanks mate. I'm going to give that a shot.
love the videos, keep em coming!
Very good. Thanks
Very nice! Thanks! Go on!
Any chance of doing a video on how to use blending thinners in aerosol form? U Pol bend 9 for example.
Just found your channel. Good stuff. Subscribed
@Mad4Motors_
6 жыл бұрын
Thanks video coming next week!
I dont even have a car, but this is so satisfying, reason i subbed :D
Great channel very informative.. cheers
@Mad4Motors_
6 жыл бұрын
Hey thanks
But what If is yellow xo I use a lower grid sand paper or do I use 800 till is dull clear
Thanks for the great videos. I did this to my headlights and used a 2K clear coat. Unfortunately I got bad orange peel. Would you suggest wet sanding and polishing them?
@johnkaimins9998
2 жыл бұрын
Wet sand and polish provided you have applied 3 good coats, otherwise you will sand through the lacquer and expose the plastic again.
Would this work on plastic tail lights? Bought an '87 Tercel, and it seems like the tail lights are smoked, a bit too dark and It's hard to see the blinkers' lights.
Good shit!
Do you think buffing it between sanding it with 2500 and applying the clear would get an even better shine?
@johnkaimins9998
2 жыл бұрын
No.
Would 2k clear coat be ok to use on the lights? Great video as always. Cheers.
@johnkaimins9998
2 жыл бұрын
According to my research 2k clearcoat is the ONLY product to use!
@hobo1704
5 ай бұрын
It's the only way it should be done. Polishing is a waste of time..
That looks great. Please tell me for how long the clear paint can last? I sent my car to have the headlamps made clear but it last for just a month.
@zaink7037
5 жыл бұрын
I would of thought they last longer. Did they use UV resistant clear coat or a good coat of it? Something a guy told me in my local detailing shop is to use a ceramic coating over the headlights. Would last several months to 1-2 years
Is it made from plastic or glass? Can do this method on both media?
@johnkaimins9998
2 жыл бұрын
This method is only for plastic. Glass does not fade or discolour because it is ...... glass.
I wish you were my neighbor, I could use you at my farm... :) Great job!
@gioolioplus
3 жыл бұрын
Use tools, not people
Ok I got thr 800 grit sand paper but what was the other one? Also how long would you say the clear coat should last? Also thanks alot for your videos brother I'm learning alot!
@mckeon1960
4 жыл бұрын
800 and 2500, should last the life of the car if you don't the clear coat uv paint says it all in video
Any suggestions on how to deal with condensation on headlights?
@Jackleeds206
Жыл бұрын
drill a small hole in the corner to ventilate
What is conditions of headlights right now ?
Can I light polish it after it's well dry? Cause it's looks a bit matte...
@Mad4Motors_
6 жыл бұрын
maybe give it a little sand and re clear
@alexrebelrebel
6 жыл бұрын
Mad4Motors Thanx! Great videos!
@johnkaimins9998
2 жыл бұрын
@@Mad4Motors_ Extra coats must be applied within 30 -60 minutes to ensure the coat bonds to the previous coat.
@hobo1704
5 ай бұрын
Use 2k clear..
3:27... 144p to 720p!
Just gonna start sanding in circular motions.... Sands backwards and forwards That made laugh more than necessary
🙈🙈🙈
I tried this but got cracks thru my clear coat, HELP!
@johnkaimins9998
2 жыл бұрын
You must sand back to the plastic again. Thorough prep is ESSENTIAL. If you can, remove the headlight from the vehicle to ensure thorough cleaning around the edges of the headlight. Final sanding grit is 1000. Using a finer grit risks the clear coat not sticking to the plastic. THOROUGHLY clean the head light with isopropyl alcohol using a lint free cloth to remove ALL traces of waxes and contaminants. Apply the first coat lightly, then 2 good coats 20 minutes apart. This is easier if you have the headlight removed because you can lay it flat to reduce the risk of runs. Wait 30 days before polishing/ sealing with wax, otherwise you prevent the solvents in the clear coat from "out gassing" trapping them under the wax. Good luck.
You should of swapped out the acrylic lacquer for battery acid.
use t cut it does the same job but with half the work
@hobo1704
5 ай бұрын
And only lasts a few months..