How to replace MAP sensor on VW Jetta p0106
Автокөліктер мен көлік құралдары
Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic.
RB The Mechanic. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RB The Mechanic.
#vw #cwmapsensor #p0106 #vwp0106 #vwjettamapsensor #replacemapsensor #manifoldpressuresensor
Пікірлер: 82
Preciate the vid bro really helpful and i did not expect vaas/nacho varga to be this good at mechanic work
Great video saved hundreds of dollars, my brother in law and I got it done in less than an hour
@RBTheMechanic
9 ай бұрын
Nice job!!!! Good!!! Good saving!!!
thanks for the vid, appreciate you calling out the actual torx sizes. extremely helpful
@RBTheMechanic
Жыл бұрын
No problem!
Here is a tip for you good people dealing with this dreadful p0106 coming back. Check your intake manifold bolts, they may be loose. A loose intake manifold can contribute to a code p0106. Upon doing this, vlean inside the intake manifold, clean out your throttle body, clean out your hoses & check your intake manifold bolts. Throttle body - torx 30 Intake manifold bolts - either a 6mm hex or a torx 40 Clean with throttle/intake cleaner For map sensor, clean with map sensor cleaner..could be bought at walmart. Vlear out your p0206 with an obII reader. Good luck and hope it helps you.
@RBTheMechanic
10 ай бұрын
Thank you for tips
Ha. I tried the same. Bracket is in the way just a hair. Almost got to it. I’m about to do a lot of maintenance on this VW. Good video.
@RBTheMechanic
2 жыл бұрын
Yeah thank u they look complicated but fun to work on
"take it easy" as you yank it right off 🤣 awesome video tho man appreciate the hard work and it helped get rid of my check engine light
@RBTheMechanic
Жыл бұрын
Yeah I changed the sensor and kept getting intake temp code new part be defective
@paulmaleski5872
9 ай бұрын
@RBTheMechanic Did you find out what the issue was my vw is running 5 codes rn....
Thanks for the vid. Keep doing what you do.
@RBTheMechanic
Жыл бұрын
Yup thank u
I greatly appreciate this information
@RBTheMechanic
Жыл бұрын
Thank u sir glad video was useful please subscribe
Also. You can remove the back upper clamp and get the sensor off. Same car. I just did it to see
Man thanks for the video i really need it 🙏🏽 ❤
@RBTheMechanic
Жыл бұрын
Welcome
Sick! I gotta do this job, and thanks to you, easy money! Kudos my guy! Earned my sub!
@RBTheMechanic
Жыл бұрын
Thank u!!!
Thank you for sharing! Great video!
@RBTheMechanic
5 ай бұрын
Thank you
thank you, worked like a charm!
@RBTheMechanic
3 ай бұрын
Nice good job!
Thanks for the video but you mentioned a "Torque" when you were inserting the bolt that holds the sensor in place. What is the required torque there please??? Thanks again.
@RBTheMechanic
Жыл бұрын
Didn’t find the torque so I did it softly by hand
Quick question, you said the map sensor clamps when connected, when taking it off did you have to use a tool to unclamp or it pulls right off?
@RBTheMechanic
9 ай бұрын
Connector u mean? Idk why I said clamp it got 2 bolts and connector and it pops off
Perfect video 🤘🏻 thanks
@RBTheMechanic
Жыл бұрын
Glad you liked it!
Having trouble finding a replacement torx screw for the map sensor at the intake manifold, it looks like bolt for the throttle body only smaller, online extensive searches come empty and have ordered countless wrong bolts from Fcpeuro, any help part# and size l think it's t20 but I stripped out the head that's why l need new one.
@RBTheMechanic
2 күн бұрын
Oh ok match somthing
I need to clean wife's 2010 Golf's throttle body and MAF air flow sensor for the 1st time even though there is no problem. Do you think I will gain some performance back?
@RBTheMechanic
Жыл бұрын
No preformance back but it is service that will make the car idle start up better go for it
Great video, thanks. What would you say a shop would charge for this job?
@RBTheMechanic
3 ай бұрын
Labor like $140 unless they diagnose and order part then lot more
Nice swivel .bada bing bada boom😂
@RBTheMechanic
Жыл бұрын
Yup
@RBTheMechanic
Жыл бұрын
Always make life easy
I have a 2008 vw rabbit 2.5L and it's a p0108 code is there a way to fix the high input or do I need to take it to a VW dealership to replace it?
@RBTheMechanic
Жыл бұрын
Replace the map sensor!!! Get good quality or maybe buy it from the dealer
@xoxo_dumbgirl2198
Жыл бұрын
@@RBTheMechanic okay will do thanks for the advice!
@RBTheMechanic
Жыл бұрын
@@xoxo_dumbgirl2198 welcome!!!
Does 2012 passat has Mass air flow sensor? Or just MAP?
@RBTheMechanic
8 ай бұрын
It might have map
@ricardov8633
Ай бұрын
Hey, I have a 2013 I have the same question? so what was it and did it come back? Check engine light.
Hey. I’m bout to do this now and clean throttle body?? Any suggestions?
@RBTheMechanic
2 жыл бұрын
Which car u got
@TourettesMobileMechanic
2 жыл бұрын
@@RBTheMechanic oh FYI. I was able to remove it without removing the throttle body. It was not hard. However. It had to come off. 2008 Jetta 2.5 l MK5. I had a break on the pigtail it had damaged the sensor. I finally Found the break and correct it with a ouch pin adapter into the old barbed and walla. Now I’m trying to figure out how the H ima get the this thermostat. Ima assuming ima have to take the whole manifold off it tucked in, I’m just about done. I need it get paid and this has been hell. Over all looking good I just hate the clips. Everyone is just seized, I have broken like 5 but spark plugs are in and it’s done. Many of my coil packs well 3 decide to break at the very end and I had to spend hours fishing the rubber out but I got it done and the others is also my throttle body is so clean you can eat off it. I should have it wrapped up pretty fast tomorrow and I also got the oils leak straight from the vacuum pump gasket, going smooth so just manifold thermostat and the temp sensor and out it alll back together. It should be fixed at the connection. I almost missed it but I caught it after one reassembly and take back alart there it was. Lose TB running against the thin 0.5 yellow white strip wire. That was the major issue. Video should post soon I can’t wait to get it done tomorrow. I’m beat .long day. Just need a couple things and the correct size tripped hex te fit inside the middle whole of the manifold. Should be fun. Jus my about something and I’ll keep you payed I am trying to have done by 4 pm tomorrow, should be no problem. was not easy though. Thanks again.
Why did you replace it, what were the symptoms?
@RBTheMechanic
5 ай бұрын
It had code for air temp sensor
Did you say a T27 was needed?
@RBTheMechanic
Жыл бұрын
Yup
Can this sensor be the problem if my code says air leak in manifold?
@RBTheMechanic
Жыл бұрын
I doubt that could be vaccum leak pipe hose or seals
@Rod-oh4sy
Жыл бұрын
@@RBTheMechanic thanks for the reply, I'll check them out brother keep them videos going you are really helping a lot of people 👍
Why didn’t you just cleaned the old one with proper spray cleaner? Thanks
@RBTheMechanic
6 ай бұрын
Nope this shouldn’t be cleaner
Hey, I got a code saying manifold absolute code P0106 on my 09 2.5 jetta, will replacing the map sensor fix this?
@RBTheMechanic
4 ай бұрын
Yes that is the only option I have also get original sensor
@geraldg4631
4 ай бұрын
@@RBTheMechanic thank you! also thanks for the reply it is very appreciated
@RBTheMechanic
4 ай бұрын
@@geraldg4631 welcome!! Always here to help don’t forget to subscribe
I have a code P2188. Would a oily map sensor cause this?
@RBTheMechanic
Жыл бұрын
It can but u gotta replace it regardless
@theasim3757
Жыл бұрын
@@RBTheMechanic thank you for the reply. Why do you say I have to replace it regardless?
@RBTheMechanic
Жыл бұрын
@@theasim3757 if it got code for it and u think it’s the oil build up usully that happnes it gets inside also blocks it
@mr.mr400
5 ай бұрын
If its new and it got oil on it can it be cleaned
@theasim3757
5 ай бұрын
@@RBTheMechanic I appreciate your content
how much do the MAP senser cost
@RBTheMechanic
3 ай бұрын
Like $120 in good quality
Yeah what year is this model? More infoe better video
@RBTheMechanic
Жыл бұрын
I think this one was 2011
Hey Ralph Bob The Mechanic!!,😂😂 You're saying it wrong!,😡 it's not called Volkswagen!,😠😡 is called Broke-wagon😂😂 or Choke-this-wagon!!!🤣🤣😂😂🤣
@RBTheMechanic
2 жыл бұрын
Haha good one!!
@Joserocha-wm9de
2 жыл бұрын
😂😂😂😂😂😂
Passat 2012 2.5 code p2187
@RBTheMechanic
2 ай бұрын
Lean code start with replace AF sensor
@user-pi5wm8rf5n
2 ай бұрын
@@RBTheMechanic af sensor ?
I did this and code still reading and have performed issue
@RBTheMechanic
2 ай бұрын
I had faulty sensor I would get new one from dealer
@mikesummers47
2 ай бұрын
I replace that map censor and that cover above the throttle body. After a nice drive on the interstate at high speed it corrected itself and the light went off