How to Replace Front Wheel Bearings 2000-2006 Toyota Tundra
Автокөліктер мен көлік құралдары
Buy Now!
New Wheel Bearing from 1AAuto.com 1aau.to/ic/1AAXX00119
This video shows you how to install new front wheel bearings from TRQ on your 2000-2006 Toyota Tundra. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This process should be similar on the following vehicles:
2000 Toyota Tundra
2001 Toyota Tundra
2002 Toyota Tundra
2003 Toyota Tundra
2004 Toyota Tundra
2005 Toyota Tundra
2006 Toyota Tundra
Tools you will need:
• Flat Blade Screwdriver 1aau.to/obns/1AXAA00013
• 10mm Socket 1aau.to/obeE/1AXAA00017
• 12mm Socket 1aau.to/obyV/1AXAA00015
• 17mm Socket 1aau.to/obyV/1AXAA00015
• 19mm Socket 1aau.to/oajE/1AXAA00043
• 21mm Socket 1aau.to/oajE/1AXAA00043
• 35mm Socket 1aau.to/oaq/1AAST00005
• Bearing Puller
• Brake Caliper Hanger 1aau.to/oji/1AXAA00439
• Press
• Needle nose pliers 1aau.to/oEa/1AXAA00051
• Needle nose pliers 1aau.to/oEa/1AXAA00052
• Pliers
• Side Cutters
• Snap Ring Pliers
• Ratchet 1aau.to/obEj/1AXAA00016
• Socket Extensions 1aau.to/obyV/1AXAA00015
• Torque Wrench 1aau.to/oaIc/1AXAA00044
• Drill Bit Set 1aau.to/oaB/1AXAA00141
• Gloves 1aau.to/oadG/1AXSS00048
• Safety Glasses 1aau.to/o6J/1AXAA00343
• Chisel 1aau.to/okR/1AXAA00055
• Floor Jack 1aau.to/o77/1AXAA00068
• Hammer 1aau.to/oVg/1AXAA00091
• Jack Stands 1aau.to/oVI/1AXAA00065
• Punch
• Rubber Mallet 1aau.to/og6/1AXAA00413
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Пікірлер: 11
√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money
Thanks, I followed instructions and the new bearing is now shot, thanks for the help
We just gonna ignore all the rust? 👀😬
When pressing the new hub you didn’t explain the setup holding the bearings in place, also you should pack the cavities around the seals and bearings with grease also around the cap, this prevents early water intrusion
What size of race are you using to press the bearing out?
How far do you press the new hub?
He did not take the time to show how he reinserted the HUB after having pressed in bearings and hammered on the seals. He showed how it was pressed out. I’m about to tackle the job and will rent the set of different diameter cylinders Nedra to support the bearings as I press. One could easily press apart the bearing races or loosen them if they aren’t properly supported while pressing on the hub or ANYTHING. Am I correct?
Is this for RWD or 4x4?
Hi everyone! Have a dilemma here! I changed both front wheels hub and bearings, installed new tires, new ball joints, new inner and outer tie rods on both sides, realigned tires and the noise still there (humming noise) it can only be heard while driving inside the cabin, I put the GoPro and doesn’t pick up the noise at all! Any one knows something else that could be causing this noise? Is driving me crazy! Please help! Thanks
Wow! I have a 2000. No rust. That truck has or had a terrible owner. I live in kcmo, so there is plenty of salt used in the winter
50 steps and $10k worth of equipment later