Well explained, your voice is well suited for the videos

@gerhard5911

3 ай бұрын

Thx, been many years ago. I would do it different now I guess. Less of the hammering lol

Weekend warriers like us need to earn our tools. You certainly earned a few more tools with this job, good work! I'd start with a good set of jack stands, it's a scotty kilmer job with only a jack.

Great video! Very useful for me & my adventure replacing the wheel bearing on my '09 Prius. A couple pf things that this video does not cover: 1. The shield around the speed sensor in the back of the bearing. I removed this with only a little trouble by first removing the entire yolk/knuckle assembly, then gripping the shield with a pair of Vice-Grips and whacking on the yolk while holding the Vice-Grips. 2. I found this bearing was very, very hard to remove. My Prius grew up in Upstate NY State where there are awful road conditions for a few months a year. Salt, sand, snow, cold temperatures, etc. This puppy was STUCK, and hammering on it was pretty useless. Ultimately, I took the entire yoke/knuckle off & was able to put the assembly in my vice, pointing down. Being careful, the jaws of my vice would fit just between the bearing assembly and the knuckle. I didn't clamp down with the vice, just used it to hold the yolk, while beating on the bearing. I put the four bolts in most of the way then, using an impact socket to buffer the hammer blows, I whacked the heck out of the socket, one at a time on each bolt. This ultimately did the trick. This bearing was far and away, the most stuck thing I have ever liberated. It was glued (corroded) in the yolk like nothing I have encountered. I practically soaked the thing in penetrating oil ahead of time and, after I got it apart, I could tell that the penetrating oil didn't touch the corrosion. It was super-stuck. I tried heat and pressure, using a propane torch and fitting a small hydraulic jack between the hub bolts and the frame. These may have loosened the bearing assembly, but I'm not sure. 3. One thing I learned from this was to use some non-hardening sealant, and anti-seize compound to reassemble this puppy. I think that this was the fifth front-end wheel bearing I have replaced on my '09 Prius (220K miles) and I hope the next time is easier.

Thank you gothard Schiller for this video it will help me to do my own car when future wheel bearings needs replacement.most appreciated.

Thank you for uploading the video. This will help me out when I need to replace mine.

Thanks a lot! It made me decide to do this myself in stead of taking it to a shop.

Great video! Thanks for sharing!

For anyone doing this be sure to check for sticky front brake pads and assure your tires aren’t contributing to noise. I did mine recently and it helped but the other influencing factor was cupped tires due to worn struts.

Decent job! Very inspiring. However, everyone ! Please be sure to torque the bolts on the new hub and use jack stands so you dont have a nasty accident while beating on things.

@gerhard5911

5 жыл бұрын

Thanks for pointing out the jack stands and the torque. Both are very important details.

Punch out the wheel studs, you can use a longer bolt with a nut to pry out the bearing, On my case it split the bearing in 2 which allowed me to lay it on top of a couple of 4x4 boards and hammer out the bearing. It would be more stable than holding onto the assembly and beating on it, In my case the bearing was really seized and it took a considerable amount of beating to remove, Good video,

Good job. A suggestion next time, instead of whacking the wheel bearing with a sledge hammer, why not leave the cap bolts loosely in (unthreaded say about 1/4 inch) and then strike at the bolt heads with a drift punch. By alternating from one side to the other, you can then "walk" the bearing assembly out of the spindle hub assembly. You might also be able to do this while the spindle is still attached to the strut. This way you don't have to do an wheel alignment at the end. Cheers!

@gerhard5911

5 жыл бұрын

That's is a great suggestions. Thanks. I should finally get myself a press. Would make it much easier.

@TDCornwell

5 жыл бұрын

This method (sort of) worked for me. Nothing else did. I took the entire yoke /"knuckle" off & was able to put the assembly in my vice, pointing down. Being careful, the jaws of my vice would fit just between the bearing assembly and the knuckle. I didn't clamp down with the vice, just used it to hold the yolk, while beating on the bearing. I put the four bolts in most of the way then, using an impact socket to buffer the hammer blows, I whacked the heck out of the socket, one at a time on each bolt. This ultimately did the trick. This bearing was far and away, the most stuck thing I have ever liberated. It was glued (corroded) in the yolk like nothing I have encountered. I practically soaked the thing in penetrating oil ahead of time and, after I got it apart, I could tell that the penetrating oil didn't touch the corrosion. It was super-stuck. I tried heat and pressure, using a propane torch and fitting a small hydraulic jack between the hub bolts and the frame. These may have loosened the bearing assembly, but I'm not sure. One thing I learned from this was to use some non-hardening sealant, and anti-seize compound to reassemble this puppy. I think that this was the fifth front-end wheel bearing I have replaced on my '09 Prius (220K miles) and I hope the next time is easier.

@2:29 "wow thats very loose, just how like it!" lmao

Very thorough, thank you, gotta do my gals "pretty lil" Prius. Keep her happy, and my wallet not so slim. Times is a gitting 'ruff out there..... Thanx guy..... You from up Jersey way?

Just did mine, I had to resort to a 6 ton press, but it is all corroded like that because that's what aluminum does when it contacts steel.

At 38:30 you showed the ring. What is that ring for?

Getting that bearing out is a SOB isn't it? Good work sticking with it. Thanks for sharing your experience.

@nordicpride9708

4 жыл бұрын

Usually only if the car spent any time in the rust belt. You do get some corrosion being that they are two dissimilar metals (aluminum knuckle/steel hub). But nothing a mini sledge can’t persuade.

@gerhard5911

4 жыл бұрын

@@nordicpride9708 Chicago area car...that definitely qualifies for rust with all the salt on the roads.

wheel bearing ez, dont take the hub off like he did, take the 2 thick bolts out and hammer out the axle then unbolt and hammer the bearing out, its E Z, dont take off the bottom castle nut or steering thing

Good job in diagnosing & tackling problems with front wheels; some observations: - you are a MONSTER & a force to recon with the mini sledge hammer!!! whack... whack... ; ) - dust shields mangled and all - i normally liberally spray brake clean lubricant also helps in cleaning metal parts. - normally liberally Spray lubricant to help loosen metal parts to unscrew - are you ready to upgrade to a work bench & vice assembly? - I noticed that you didn't use a jack stand to suspend your car; its only a problem when there IS a problem. - Loose front wheel causes can be of various causes: - BEARING HUB. this is definitely the MAIN cause of your road noise, speed, pull. - LOOSE AXLE NUT, you noticed that loose nut immediately off the bat when you unscrewed it off the axle. It normally is ~170lbs torque, you took it off with about 30lbs of effort. I assess that you did some work on that axle as of recent that caused it to relax its tension. Probably need lock tight the nut back to seat in. - BALL JOINT. this also may cause your wheel to click - nice looking Prius - thanks for sharing your project

@gerhard5911

6 жыл бұрын

Yes, you are correct. Just know, I did spray the day before. And no, didn't want to come out. I have a press at my shop which I normally would have used. But the monster in me just wanted to get the job done. The axle nut did come off at less the 170. Great observation. If I remember right I may have loosened them before filming. Ball joints checked out. If you would have heard the extremely loud grinding noise you would have been shocked. I even thought there was something wrong with the drive train after replacing the loose left side and the noise was still present. After the repair was done I knew for certain in THIS case it had been the wheel bearings. But when I started I was about only 80% sure. Thanks for the comments. I am aware that there are some more refined and elegant ways to do this job, no doubt. And thanks for reminding me for not becoming sloppy on the blocks. After all I had the jackstands right there.

Machine that hub assembly seat face 3 thousandths over!

Does it matter which brand bearing you buy

@gerhard5911

5 жыл бұрын

depends on how long you want to keep the car running well. If its an older car. no

@DrEarbuds

5 жыл бұрын

@@gerhard5911 my Chinese mechanic use a jackhammer to loosen it up

Smash that cast aluminum!

I don’t think it should’ve been that easy to get the axle nut off

Did you ever get a metallic taste in your mouth after doing this job? Because I did. I used a simple dust mask. Should of used a better mask for the job.

@LostinCynicism

6 жыл бұрын

Stroke probably

@gerhard5911

5 жыл бұрын

no, I didnt

You remind me of Donald Trump working on his constituents viewpoint. Great job