How to Replace Front Upper Control Arm 2007-2014 Cadillac Escalade
Buy Now!
New Control Arm with Ball Joint from 1AAuto.com 1aau.to/ib/1ASF...
Control arms are a crucial part of the suspension system of your vehicle. They not only carry the load of the vehicle to the wheel, but they typically also maintain its alignment. Control arms are typically large and strong, so you may be surprised it needs replacing. They contain rubber bushings for smoother rides at the cost of eventual wear, or integrated ball joints that require replacing the entire arm when they wear. This video shows you how to install a new quality TRQ lower control arm with ball joint in your 2007-2014 Cadillac Escalade.
• Check here for more videos on the 2007-14 Cadillac Escalade: • Cadillac Escalade 2007...
This process should be similar on the following vehicles:
2007 Cadillac Escalade
2008 Cadillac Escalade
2009 Cadillac Escalade
2010 Cadillac Escalade
2011 Cadillac Escalade
2012 Cadillac Escalade
2013 Cadillac Escalade
2014 Cadillac Escalade
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXA...
• Pocket Screwdriver
• Pry Bar 1aau.to/oa/1AXA...
• 21mm wrench
• 10mm Socket 1aau.to/ob/1AXA...
• 21mm Socket 1aau.to/oa/1AXA...
• 22mm Socket 1aau.to/oa/1AXA...
• Pickle Fork
• 1/2 Inch Air Impact Gun 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oa/1AXA...
• Socket Driver
• Socket Extensions 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Bungee Cord
• Copper Anti-Seize
• Floor Jack 1aau.to/oa/1AXA...
• Hammer 1aau.to/oa/1AXA...
• Jack Stands 1aau.to/oa/1AXA...
• Rubber Mallet 1aau.to/oa/1AXA...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Cadillac Escalade 2007-14 3rd Gen: • Cadillac Escalade 2007...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Пікірлер: 17
√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*
Thanks for the tip on leaving the plastic piece in. Other videos just say to pop it out and then go an alignment process with the car loaded measuring where the arm height was and all sorts of gyrations. I haven't done this yet but wondering if that's what they use at the factory, why not use it.
When replacing the whole control arm with the ball joint. Does it matter if you have aluminum or steel steering knuckle????
Why the axel nut need to be torque
Why did you have to tighten the hub nut?
Awesome , clean and well done
Thanks a million for giving me the idea to use a impact to get my bolts out there rusty as f.
@TralfazConstruction
Жыл бұрын
What did you end up doing? I had a problem with rusty bolts fused to the steel bushing sleeves three and a half years ago. Had to cut them all off. It was tedious to say the least.
Is that the same guy that’s on the A1 auto videos? I think it is lol
Fantastic video!
Is it really 140 foot pounds for the upper control arm bolts??? I read it's 66 foot pounds. I set mine at 140... Or tryed to and it twisted the bolt head off... What is the correct torque spec?
lol i wish it was that easy on all of them I live in Massachusetts and my bolts were rusty as hell one bolt broke and the other one was ceased on the rubber bushing. I had to use my 4 1/2 inch cutoff wheel to cut the bolt off.I had to remove the strut to cut the bolt off.Great times...lol
@TRQ
3 жыл бұрын
+Eladio Rosa Thanks for watching our video! 1aau.to/m/Shop-TRQ
Tell the bolt sizes next time
Verkle
That's not how to use cotter pins
He don't know wtF he doN.. don't remove any steering parts for 1.. and definitely don't remove the cvaxle nut.. and yes 140lbs.. too much. Engine heads get torqued at 90lbs..