Sir thank u sa video mo natuto ako pano mg replace Ng drill chuck more bless sa channel mo sir..now I know...yes!!

Nice dahil sayo madamikang natutulongan mga carpenter

Very helpful boss galing napalitan ko na chuck ko nabasag kasi ang bit kala ko may naiwan pang turnilyo big help talaga

I used kzread.infoUgkx4ynqaujg7rZKFapA8s29kTpRszJGa3-K this for the first time today to replace the front wheel bearing on my rwd 98 dodge dakota. This had absolutely no issue removing or reinstalling the lug nuts and it took off the axle nut without any struggle. Sounds like it's got some muscle to it. Time will tell

Let me give you some words of advise. Get some sheet lead and line those jaws with the lead. Clamping down on those gears with steel jaws will ruin some gears. The lead will cushion the gear while holding it stable.

@MarioAPN

Жыл бұрын

Wood is also an option. Wooden plank.

Open the chuck jaws. Remove the screw located in the centre. Fit a 3/8" (10mm) Allen key into the chuck and tighten with the chuck key. Smack the end of the Allen key with a hammer in an anti-clockwise direction and it will unscrew from the machine. Refitting is a reversal of this procedure. You do not have the split the drill body.

@kenpoman1

3 жыл бұрын

that method doesnt work with this particular model makita 6404 the shaft still spins in both directions when you put the allen key in it and there is no flat on the shaft for a spanner to hold it to smack it with a hammer. That model is about 40 years old.

@tony5006

3 жыл бұрын

@@kenpoman1 You do not need to lock the spindle. The inertia will free the chuck eventually.

@davidwillard7334

2 жыл бұрын

The END !! of the Allen ! Key ! ?? You Either ! Bend ! Or ; Break ! Or DAMAGE ! the Drill !.Doing that !!

@hsbrooks

2 жыл бұрын

@@davidwillard7334 - Ah, No.You've apparently changed a drill chuck or used a hex key.

@tamazkapanadze3383

Жыл бұрын

21 21 56

Desde colombia. Gracias por el video. Solo es que el tornillo que sujeta al mandril es rosca izqierda para que tomen nota y miren como gira el destornillador. Gracias vale.

nice bro maraming matulongan

Great Video! This is the only way to change the chuck if your drill spins too loosely to untighten the chuck the other way. The other way is tightening the chuck on a hex wrench and hitting it with a snap. My chuck was actually stuck in the open position so I couldn't tighten it on a hex wrench....this video saved my drill! Thanks.

@clarkstarks6767

2 жыл бұрын

What if it frozen to tighten position? I cannot loose it..

@welostourdemocracy

2 жыл бұрын

@@clarkstarks6767 ....have you tried PB Blaster and a pipe wrench to loosen it? that should loosen it to allow access to the center screw.

@davidwillard7334

2 жыл бұрын

Sounds like ! YOU ! STUFFED !.! IT ! UP !! EVEN !! MORE !! NOW !!

Thank you po Sayo sir.maaayos Kona itong sira na electric drill na SI na Ang drill shop.

Thanks for the video. If the video had been available many years ago I would have replaced the chuck on my old B&D. Replacement parts were more readily available and cheaper. These days the replacement chuck costs as much as a new drill so I would just toss the worn-out B&D and buy a new one.

@davidwillard7334

2 жыл бұрын

And Still ! Have ! PROBLEMS ? With that ! Too !!

Canal show de bóla dicas top mesmo parabéns amigo 💯👍👍🇧🇷

ကျေးဇူးတင်ပါတယ်ဆရာ.....နည်းလမ်းလေးဝေမျှပေးတာ

Thank you very much, now I can easily replace mine🇿🇦

Thank you, that helps me.

Good nagkaroon ako ng idea thanks

Thank you so much for sharing this video idol keep safe and stay healthy idol Godbless you always 🙏😍❣️

lol.that was easy.glad the gear didnt break when you lock on the vice.😅

Very good information, thank you bro

Maraming salamat sa kaalaman bro stay safe god bless.

Thanks it is good video but it can be replaced without opening the cover..

@mysarababekir569

3 жыл бұрын

How to fix a rod will turn with key

Very good idea thanks

kafi bidwan ho bhaisab aap..gear ko vice me tight kardiye bina packing k... naman aapko

DE VALT ,10mm ഡ്രിൽ മെഷീൻ റെ ബോൾ ബെറിങ് കിട്ടുമോ നമ്പർ അറിയില്ല

Good idea dear

Great job and good video if u move the music🙏👍🤣🇩🇰

Amigo creo que debiste colocar algo,entre las quijadas o mordazas de la prensa, algo así como unas tiras de madera, para no dañar el engrane.

@luisfernandez-np3yh

Жыл бұрын

Muy buena su observación yo también me di cuenta.👍

Hvala na savjetu

never seen it done like this before. There is a much easier way

Exelente video

Thanks for video now I can replace my drill chuck

@davidwillard7334

2 жыл бұрын

And Damage !. The! Gear ! Too !

Bos sy butuh buat merk bor maktek ...

Thanks for showing the long way to do this

Very nice 👍👍

Awesome instruction video 😎

Very good thanks you

Usta o MANDRENI böylemi değiştiriyor aslında çok basittir

Solo tienes que meter algo en el aspa para que no ae mueva y girar el trompo del lado contrarip de comongira y ae suelta y metes el.otro listo

maraming salamat boss godbless

The 'smack with a hammer' technique probably applies to older drills. I have a drill dating from about 2015 and wanted to remove the chuck. Unbeknown to me, there is a screw, left-hand threaded accessible with an Allen key placed into the fully open chuck. Old man with 'weak' hands that I am, trying to undo this screw as though it were normal RH, snapped said screw in two. Drill and driller are both fine but replacement LH screws are not that cheap or readily obtainable!

Sir sira po angle grinder brand makita naupod po ung carbon nasagad q po nung palitan q ng carbon brush parang sinusunog nalang nia ano po dpat gawin dito tnx..po..

Very nice video thank you sir very much.

You don't clamp gear on a vice Steel to steel .you can use Taflon or copper in between To avoid damage the gear. To replace chunk today is not Profitable as too many cheap Chinese drilling machine on the market

Vejam meu vídeo como tirar o mandril sem desmontar a máquina

i am learning thanks.

@quyennguyenang1061

3 жыл бұрын

Yyyyyty

@davidwillard7334

2 жыл бұрын

Sounds ! More ! Like !! STEALING !! THAN ! ! ANYTHING !! ELSE !!

unbelievable, unscrew the whole Drill to change the chuck; he did not need my friend

My B/D drill with attachments to fix I just have to put bit tighten key & give it slight blow from a hammer to remove the chuck to fit attachments, eg. saw, orbital sander etc. No need to remove any screws or open the body cover.

You use vise to hold the thread?. It can damage the teeth

Kesuen langsung copot baute didrip kendoni

ILike 😻😻

@kannaapple432

3 жыл бұрын

💞💞💞

Merci pour l’astuce . J’ai un problème pour changer le mandrin je ne sais pas comment m’y prendre.

good video

It can be done unscrewing the machine.

You replace the chuck but you damage the gear.

@githenyaJoseph-kn2vr

11 ай бұрын

😂

@user-pd7xo3qj6s

9 ай бұрын

Tama😂

@Chalc2

5 ай бұрын

Senseless way

San Kya nkbibili ng pmalit

What make is this drill anyone any ideas I've got one the same nut the lable is missing

THANK YOU FOR YOUR CLEAR VIDEO

When do you chage a drill chuck ? Blund ?

Para que sirve los controles

👌👌👌

thanks bro

Music ke bina drill khulta nahi shayad

Thank you for your post. I like this vd.

Good 👍

Sir kapariho din ba ng black&decker yang nasa video nyo

I would bet Noah was the previous owner of the vice.

First and foremost, you don't really need to pull out the gears in order to change the chuck. Looking at the damage on the collet gears, it seems that you are a rough user. This is further demonstrated by the way you clamped the gears directly to the vise. I am not surprised that you will soon be changing another chuck in a very near future.

@sathishsukumaran9977

3 жыл бұрын

True 😂😂

@mytrickshots6105

2 жыл бұрын

I think putvthe gear below so that it does not demage

For a 9 mins video he has taken 4 mins to adjust camera.

I have a 10 mm chuck fitted in my drill which I want to change to hold 13 mm Chuck which can be used for 13 mm bits. What I had to do for this conversion.?

@san.jsan.j3238

3 жыл бұрын

Oooo yes

@AnkitKumar-rb5uh

2 жыл бұрын

Add drill sleeve in it and then fit the drill

@davidwillard7334

2 жыл бұрын

Buy ! a New Drill !

Anung brand po nun drill?

👍

great.

It looks like you cheeched the teeth on that gear by clamping it unprotected in your vice. I could see the damage when you removed it. You need to put some wood, leather, or something else between the vise jaws and your workpiece to prevent marring.

Vice the gear to open the chuck ??

@RickaramaTrama-lc1ys

4 жыл бұрын

Yes I was cringing to see the gear vised against steel jaws. He installed failure into the gearing of the drill motor~!

Salamat po info sir

you have seen the hard way now i will tell you the easy way place drill in vise open chuck insert screw driver turn clockwise to remove the screw insert the key in chuck give it a good (WACK) counter clockwise now unscrew old chuck add new chuck install scew counter clockwise you are thru a 5 min job..

@hunchojack1858

3 жыл бұрын

My drill dosent have a screw in the middle what do I do

@davidwillard7334

2 жыл бұрын

Another STOPWATCH !! IDIOT !! HERE !!

@drpayne1519

7 ай бұрын

NO SCREW INSIDE THESE CHUCKS

nice

Thanks for your time, but I don't disassemble the drill to disassemble the chuck, I have a used key that enters and blocks the axis and then I unscrew the chuck

Wrong method... Between the steel wise plates, Gear will get damaged

@carlbruschnigjr1757

3 жыл бұрын

He should have clamped it between two pieces of hardwood.

@sathishsukumaran9977

3 жыл бұрын

No need to takeout output spindle and gear assembly to remove the chuck. Allen key and a strike with a hammer would have done the work 🙁. I replaced the chuck of my skil 13mm drill by the above method.

@maccnews5852

2 жыл бұрын

Yes, you'r right to say.

Thanks you sir

HAI GOOD AFTERNOON SUPER idea SUPER WORKING SUPER Replace Another THANKS 👍👍👍👌👌👌🌹🌹🌹

Mas maganda cguro kong samahan mo ng instruction o magsalita ka para mas lalong maintindihan ng nanood

Brilhante a essa eu vou aprender 😃👍

@trishatogonon6685

Жыл бұрын

puoding maka ordir ng barina yan malaking bilog na gir

R u not damaging the teeth of the cog, by clamping it directly on a vic?

@cdltek

4 жыл бұрын

yes not damage teeth of gear

@Terrestrial..1

2 жыл бұрын

That's what I thaught too. Personally I would have used a woodworkers vice or one that has wooden grips on it.

Where can i buy this chuck drill.

Grari khrab kia ap nay

Meatterial shop addresh telme

That is completely correct. When I change a tyre, I also drain the coolant first.

@davidwillard7334

2 жыл бұрын

And Lost ! The Air ! Too !!

Thanks I didn't know that

i believe you can do it without overhauling the device

👍👍👍

👍👍

TQ

Paano po ibabalik ang hammer ng drill kasi ayaw ng gumana eh

how to install of carbon to drill

use 12 mm wrench and vice grip

Looks like the vice (correct spelling!) is next in line for a makeover!

@davidwillard7334

2 жыл бұрын

Like THE ! METAL ! SHREADDER !! AWAITS ! IT !!

dapat may tela o basahan yung gear para hindi masira pre..

Can a Chuck drill be fitted on a hand grinder

@davidwillard7334

2 жыл бұрын

You can Fit a Chuck on a Hand Drill !

굿