How to Replace CV Axle Assembly 2011-2016 Hyundai Elantra
Автокөліктер мен көлік құралдары
Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ia/1AACV00404
This video shows you how to install a new CV axle assembly in your 2011-2016 Hyundai Elantra. A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications.
This process should be similar on the following vehicles:
2011 Hyundai Elantra
2012 Hyundai Elantra
2013 Hyundai Elantra
2014 Hyundai Elantra
2015 Hyundai Elantra
2016 Hyundai Elantra
Tools you will need:
• Pry Bar 1aau.to/oHI/1AXAA00020
• 19mm Wrench 1aau.to/oKB/1AXAA00010
• 14mm Socket 1aau.to/oaZZ/1AXAA00015
• 17mm Socket 1aau.to/oaZZ/1AXAA00015
• 19mm Socket 1aau.to/oZu/1AXAA00043
• 21mm Socket 1aau.to/oZu/1AXAA00043
• 32mm Socket 1aau.to/obM/1AAST00003
• Ball Joint Press
• CV Axle Shaft Popper Tool 1aau.to/od/1AXAA00127
• Pliers
• Torque Wrench 1aau.to/oajM/1AXAA00044
• Copper Anti-Seize
• Cotter Pin
• Rust Penetrant
• Drain Pan 1aau.to/os2/1AXAA00320
• Floor Jack 1aau.to/oPc/1AXAA00068
• Hammer 1aau.to/oKE/1AXAA00091
• Jack Stands 1aau.to/oKM/1AXAA00065
• Large Hammer 1aau.to/oKE/1AXAA00091
• Pole Jack
• Punch
• Sledge Hammer 1aau.to/oKE/1AXAA00091
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Пікірлер: 51
√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money
This girl genuinely knows the little tricks associated with individual tasks demonstrating years of experience. Well done! Respect.
I’ve seen tons of mechanic videos, this one is definitely one of the best ones.
Your method of disassembly and installation is perfect, and you have high experience and confidence. Greetings to you
@TRQ
Жыл бұрын
+Mohammed Suboh Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ
This is exactly what I needed!! I cant wait for more elantra part installation videos!
Great video! I used this for the most part, but since I was also changing the struts I was able to not have to deal with the ball joint. I’ve seen other videos saying to place the gap in the washer at the 12:00 or use grease to keep it centered. I tried the 12:00 advice and it didn’t work, then spun it like she says and it popped in nice and easy. Also, was able to get the passenger side out without removing the trans mount. Now, time for an alignment.
@TRQ
6 күн бұрын
+@TF5598 Thanks for watching our video! 1aau.to/m/Shop-TRQ
Thank you. I wasn't doing this project on my car but you show me something to check out while under car. Engine and transmission mounts.
Outstanding. Thank-you.
Outstanding video!
Excellent video
Thank you 🎩
Great job
Why take off the ball joint instead of just the strut bolts? Ball joints typically the hardest to remove and usually damage them. Another video says the opposite on the split on the ring, they say have the gap on top to stop the ends of it from binding:)
Outstanding !!!
Crow foot or dogbone will torque that. Great work by the way👍
Wow, no bs like a lot of boys, clean, thorough, and professional presentation! Great work, lady! I'll trust my car with you anytime.
Thank you!!!
You're the best
Thanks!
Thank You.
Good job’s
Great video! Thanks! Now, if I were only thirty years younger. 😬
Is it possible to provide us about a reason to change it, are the axle make noise or some problem with gear! because I have same model of car that’s give me opportunity to maintain the axle before I lose it. Thank you for your video it is have a lot of benefit❤.
Mükemmel 🎉
Well done. I would suggest maybe 5 seconds to emphasize safely raising or jacking the car up. Also, a list of the tools used would be EXTREMELY helpful.
does this also include a 2010 hyundai elantra as well?
The hyundai elantra 2016 need it 217 ft-lb for the axle nut ?
tq-wrench with a 19" crows foot if itll fit for that ball joint.
Would this be pretty similar to a 2020 Elantra?
I have removed the inside axle cv seek in the chamber when I was trueing to removed the seal of my 2012 Elantra . How do I get that inner chamber seal now one back in . Or is this transmission inner problem I started
I have 2011 Elantra. Your doing a 217 torque set for cv axle nut . What yr car this vid she does here .
swivel is priceless.
Is this the same way for a 17 Hyundai Elantra?
How do I get bolt out that spins with the bolt here
ممتاز
I need the axel popper for a 2017 Hyundai Accent. It needs to be 2.5" or 63 mm. Do you sell that? Does anyone sell that?!? Thanks.
Is this similar to a 2010 Hyundai Elantra too?
Ken you trying Orisontal with the tool to remove and not need remove extra parts
@TRQ
8 ай бұрын
Thanks for watching our video! 1aau.to/m/Shop-TRQ
How much is that job?
it is easier to remove the strut bols
Is the 2014 Hyundai Accent same design?
@TRQ
8 ай бұрын
+William van Gils This procedure might be different for your application. We do not currently carry the part you need or have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ
1:27 Hard to take this video seriously after watching this person mangle the once perfectly straight brake rotor backing plate like a boss. I wonder now how often things like this actually happen behind the scenes.
I think your rotors are on reversed
That lock clip at 7:41 should be at 12 o'clock position no at six.
Esta señora no sabe nada de los cuidados de las piezas, hiso muchas cosas inecesarias para sacar el eje de la transmicion. Alguien enseñele primero.
why she so rough tho
Thanks!!!